Synaptics TouchPad driver for XOrg/XFree86 ------------------------------------------ Introduction ------------ This is a driver for the Synaptics TouchPad for XOrg/XFree86 4.x. A Synaptics touchpad by default operates in compatibility mode by emulating a standard mouse. However, by using a dedicated driver, more advanced features of the touchpad becomes available, such as: - Movement with adjustable, non-linear acceleration and speed. - Button events through short touching of the touchpad. - Double-Button events through double short touching of the touchpad. - Dragging through short touching and holding down the finger on the touchpad. - Middle and right button events on the upper and lower corner of the touchpad. - Vertical scrolling (button four and five events) through moving the finger on the right side of the touchpad. - The up/down button sends button four/five events. - Horizontal scrolling (button six and seven events) through moving the finger on the lower side of the touchpad. - The multi-buttons send button four/five events, and six/seven events for horizontal scrolling. - Adjustable finger detection. - Multifinger taps: two finger for middle button and three finger for right button events. (Needs hardware support. Not all models implement this feature.) - Pressure dependent motion speed. - Run-time configuration using shared memory. This means you can change parameter settings without restarting the X server. Note that depending on the touchpad firmware, some of these features might be available even without using the synaptics driver. Note also that some functions are not available on all touchpad models, because they need support from the touchpad hardware/firmware. (Multifinger taps for example.) Installation ------------ See the INSTALL file for detailed installation instructions. Compatibility ------------- The driver has been reported to work on a number of different laptop computers. See the COMPATIBILITY file for the list. If your computer is not listed, please let me (petero2@telia.com) know if the driver works on your computer. Parameters ---------- See the synaptics(5) manual page for a description of the available driver parameters. FAQ --- * Is this free software? Yes, the source code is released under the GNU General Public License. * When will the driver be included in the XOrg distribution? This is unlikely to happen because of copyright issues. Although the GPL license is compatible with the license used by the XOrg X server, the XOrg project doesn't want to include GPL code in their source code, because it would effectively make the whole XOrg project GPL. The synaptics license can't be changed unless all copyright holders agree to change the license, but previous attempts to find all copyright holders for the synaptics source code have failed. So unfortunately, the best we can currently hope for is that the synaptics driver is included as a separate package by the major distributions. * How do I use this driver with Linux kernel 2.6.x? You need to have the "evdev" driver loaded or compiled into the kernel (CONFIG_INPUT_EVDEV). Set the "Protocol" parameter in the X configuration file to "auto-dev". Also, if you set the "Device" parameter to "/dev/psaux", the same X configuration file should work for a 2.4.x kernel. When configuring the kernel, enable PS/2 mouse support (CONFIG_MOUSE_PS2). * It still doesn't work with a 2.6 kernel. Some distributions come with an incomplete /dev directory. The driver needs the /dev/input/eventX device nodes. Try to create them manually if they don't exist already. (Look at /proc/bus/input/devices to figure out how many nodes you need.) # mknod /dev/input/event0 c 13 64 # mknod /dev/input/event1 c 13 65 # mknod /dev/input/event2 c 13 66 ... * How can I configure tap-to-click behavior? If you set MaxTapTime=0 in the X config file then the touchpad will not use tapping at all, i.e. touching/tapping will not be taken as a mouse click. If, instead, you set MaxTapMove=0 in the X config file, then the touchpad will not use tapping for a single finger tap (left mouse button click) but will for the two and three finger tap (middle and right button click). * Why did tap-to-click stop working after I upgraded from an old version? Time is now measured in milliseconds instead of "number of packets". In practice, this means that if you are upgrading from an old version, you need to change MaxTapTime and EmulateMidButtonTime to make "tap to click" work. Good values are 180 and 75 respectively. * Gnome scrollbars scroll too much when using tap-to-click. Why? The ClickTime parameter is probably too big. Try setting it to 100. Gnome scrollbars use auto repeat, ie if you press the left mouse button and keep it pressed, the scroll bar will move until you release the button. This will lead to problems if the tap time is longer than the delay before auto repeat starts. * Vertical and horizontal scrolling events are mixed up. How come? Probably because some X startup/login script uses xmodmap to remap the mouse buttons. Correct settings for the touchpad are: xmodmap -e 'pointer = 1 2 3 4 5 6 7' You can check the current settings by running: xmodmap -pp * Horizontal scrolling doesn't work in some programs. Is it a driver bug? No, probably not. Support for horizontal scroll events must be handled by the application programs. Not all programs do that yet. Ask the authors of the application in question to implement support for horizontal scroll events. You can use the "xev" program to check if the synaptics driver generates the horizontal scroll events. If you are having problems with Mozilla, try this link: http://lists.debian.org/debian-laptop/2004/08/msg00167.html * Can the driver be used together with gpm? No, not reliably, if you are using a 2.4.x kernel. The gpm driver and the X driver both try to read data from the touchpad, and if they try to read at the same time, both drivers see incomplete data and don't know how to interpret it. If you are running a 2.6.x kernel though, there should be no conflict, because the kernel driver will make sure both user space drivers receive all events from the touchpad. * How do I compile the driver? Beginning with version 0.11.8, it should be possible to compile the driver by simply running "make". This will compile a driver for XFree86 4.2.x, which will also work for 4.3.x versions of XFree86. If you have an older version of XFree86, you will need an installed X source tree. On an RPM based distribution, you can build a suitable source tree by installing the XFree86 source RPM and compile it. For example, in RedHat 9, use the following commands: # rpm -vU XFree86-4.3.0-2.src.rpm # cd /usr/src/redhat/SPECS # rpmbuild -bb XFree86.spec Then change the TOP variable in the Makefile to match the version of XFree86 you are using. In the example above, set TOP = /usr/src/redhat/BUILD/XFree86-4.3.0/xc * Can I use this driver with an ALPS Glidepoint device? Yes, see the README.alps file for more information. * The driver says "reset failed" and the touchpad doesn't work. What can I do? This problem has been reported for some Compaq models. It's currently not known why it happens, but removing the reset command from the driver appears to make it work. If you use a 2.4 linux kernel, replace the contents of the ps2_synaptics_reset() function in ps2comm.c with a "return TRUE;" statement. If you use a 2.6 linux kernel, remove the while loop in synaptics_query_hardware() in the file drivers/input/mouse/synaptics.c in the linux kernel source code. Authors ------- Many people have contributed to this driver. Look at the top of synaptics.c and ps2comm.c for details. The current maintainer is Peter Osterlund .