/* $XFree86: xc/programs/Xserver/hw/xfree86/drivers/i810/i810_reg.h,v 1.13 2003/02/06 04:18:04 dawes Exp $ */ /************************************************************************** Copyright 1998-1999 Precision Insight, Inc., Cedar Park, Texas. All Rights Reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sub license, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice (including the next paragraph) shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL PRECISION INSIGHT AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. **************************************************************************/ /** @file * Register names and fields for Intel graphics. */ /* * Authors: * Keith Whitwell * Eric Anholt * * based on the i740 driver by * Kevin E. Martin * * */ #ifndef _I810_REG_H #define _I810_REG_H /* I/O register offsets */ #define SRX 0x3C4 /* p208 */ #define GRX 0x3CE /* p213 */ #define ARX 0x3C0 /* p224 */ /* VGA Color Palette Registers */ #define DACMASK 0x3C6 /* p232 */ #define DACSTATE 0x3C7 /* p232 */ #define DACRX 0x3C7 /* p233 */ #define DACWX 0x3C8 /* p233 */ #define DACDATA 0x3C9 /* p233 */ /* CRT Controller Registers (CRX) */ #define START_ADDR_HI 0x0C /* p246 */ #define START_ADDR_LO 0x0D /* p247 */ #define VERT_SYNC_END 0x11 /* p249 */ #define EXT_VERT_TOTAL 0x30 /* p257 */ #define EXT_VERT_DISPLAY 0x31 /* p258 */ #define EXT_VERT_SYNC_START 0x32 /* p259 */ #define EXT_VERT_BLANK_START 0x33 /* p260 */ #define EXT_HORIZ_TOTAL 0x35 /* p261 */ #define EXT_HORIZ_BLANK 0x39 /* p261 */ #define EXT_START_ADDR 0x40 /* p262 */ #define EXT_START_ADDR_ENABLE 0x80 #define EXT_OFFSET 0x41 /* p263 */ #define EXT_START_ADDR_HI 0x42 /* p263 */ #define INTERLACE_CNTL 0x70 /* p264 */ #define INTERLACE_ENABLE 0x80 #define INTERLACE_DISABLE 0x00 /* Miscellaneous Output Register */ #define MSR_R 0x3CC /* p207 */ #define MSR_W 0x3C2 /* p207 */ #define IO_ADDR_SELECT 0x01 #define MDA_BASE 0x3B0 /* p207 */ #define CGA_BASE 0x3D0 /* p207 */ /* CR80 - IO Control, p264 */ #define IO_CTNL 0x80 #define EXTENDED_ATTR_CNTL 0x02 #define EXTENDED_CRTC_CNTL 0x01 /* GR10 - Address mapping, p221 */ #define ADDRESS_MAPPING 0x10 #define PAGE_TO_LOCAL_MEM_ENABLE 0x10 #define GTT_MEM_MAP_ENABLE 0x08 #define PACKED_MODE_ENABLE 0x04 #define LINEAR_MODE_ENABLE 0x02 #define PAGE_MAPPING_ENABLE 0x01 #define HOTKEY_VBIOS_SWITCH_BLOCK 0x80 #define HOTKEY_SWITCH 0x20 #define HOTKEY_TOGGLE 0x10 /* Blitter control, p378 */ #define BITBLT_CNTL 0x7000c #define COLEXP_MODE 0x30 #define COLEXP_8BPP 0x00 #define COLEXP_16BPP 0x10 #define COLEXP_24BPP 0x20 #define COLEXP_RESERVED 0x30 #define BITBLT_STATUS 0x01 /* p375. */ #define DISPLAY_CNTL 0x70008 #define VGA_WRAP_MODE 0x02 #define VGA_WRAP_AT_256KB 0x00 #define VGA_NO_WRAP 0x02 #define GUI_MODE 0x01 #define STANDARD_VGA_MODE 0x00 #define HIRES_MODE 0x01 /* p375 */ #define PIXPIPE_CONFIG_0 0x70009 #define DAC_8_BIT 0x80 #define DAC_6_BIT 0x00 #define HW_CURSOR_ENABLE 0x10 #define EXTENDED_PALETTE 0x01 /* p375 */ #define PIXPIPE_CONFIG_1 0x7000a #define DISPLAY_COLOR_MODE 0x0F #define DISPLAY_VGA_MODE 0x00 #define DISPLAY_8BPP_MODE 0x02 #define DISPLAY_15BPP_MODE 0x04 #define DISPLAY_16BPP_MODE 0x05 #define DISPLAY_24BPP_MODE 0x06 #define DISPLAY_32BPP_MODE 0x07 /* p375 */ #define PIXPIPE_CONFIG_2 0x7000b #define DISPLAY_GAMMA_ENABLE 0x08 #define DISPLAY_GAMMA_DISABLE 0x00 #define OVERLAY_GAMMA_ENABLE 0x04 #define OVERLAY_GAMMA_DISABLE 0x00 /* p380 */ #define DISPLAY_BASE 0x70020 #define DISPLAY_BASE_MASK 0x03fffffc /* Cursor control registers, pp383-384 */ /* Desktop (845G, 865G) */ #define CURSOR_CONTROL 0x70080 #define CURSOR_ENABLE 0x80000000 #define CURSOR_GAMMA_ENABLE 0x40000000 #define CURSOR_STRIDE_MASK 0x30000000 #define CURSOR_FORMAT_SHIFT 24 #define CURSOR_FORMAT_MASK (0x07 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_2C (0x00 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_3C (0x01 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_4C (0x02 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_ARGB (0x04 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_XRGB (0x05 << CURSOR_FORMAT_SHIFT) /* Mobile and i810 */ #define CURSOR_A_CONTROL CURSOR_CONTROL #define CURSOR_ORIGIN_SCREEN 0x00 /* i810 only */ #define CURSOR_ORIGIN_DISPLAY 0x1 /* i810 only */ #define CURSOR_MODE 0x27 #define CURSOR_MODE_DISABLE 0x00 #define CURSOR_MODE_32_4C_AX 0x01 /* i810 only */ #define CURSOR_MODE_64_3C 0x04 #define CURSOR_MODE_64_4C_AX 0x05 #define CURSOR_MODE_64_4C 0x06 #define CURSOR_MODE_64_32B_AX 0x07 #define CURSOR_MODE_64_ARGB_AX (0x20 | CURSOR_MODE_64_32B_AX) #define MCURSOR_PIPE_SELECT (1 << 28) #define MCURSOR_PIPE_A 0x00 #define MCURSOR_PIPE_B (1 << 28) #define MCURSOR_GAMMA_ENABLE (1 << 26) #define MCURSOR_MEM_TYPE_LOCAL (1 << 25) #define CURSOR_BASEADDR 0x70084 #define CURSOR_A_BASE CURSOR_BASEADDR #define CURSOR_BASEADDR_MASK 0x1FFFFF00 #define CURSOR_A_POSITION 0x70088 #define CURSOR_POS_SIGN 0x8000 #define CURSOR_POS_MASK 0x007FF #define CURSOR_X_SHIFT 0 #define CURSOR_Y_SHIFT 16 #define CURSOR_X_LO 0x70088 #define CURSOR_X_HI 0x70089 #define CURSOR_X_POS 0x00 #define CURSOR_X_NEG 0x80 #define CURSOR_Y_LO 0x7008A #define CURSOR_Y_HI 0x7008B #define CURSOR_Y_POS 0x00 #define CURSOR_Y_NEG 0x80 #define CURSOR_A_PALETTE0 0x70090 #define CURSOR_A_PALETTE1 0x70094 #define CURSOR_A_PALETTE2 0x70098 #define CURSOR_A_PALETTE3 0x7009C #define CURSOR_SIZE 0x700A0 #define CURSOR_SIZE_MASK 0x3FF #define CURSOR_SIZE_HSHIFT 0 #define CURSOR_SIZE_VSHIFT 12 #define CURSOR_B_CONTROL 0x700C0 #define CURSOR_B_BASE 0x700C4 #define CURSOR_B_POSITION 0x700C8 #define CURSOR_B_PALETTE0 0x700D0 #define CURSOR_B_PALETTE1 0x700D4 #define CURSOR_B_PALETTE2 0x700D8 #define CURSOR_B_PALETTE3 0x700DC /* Similar registers exist in Device 0 on the i810 (pp55-65), but I'm * not sure they refer to local (graphics) memory. * * These details are for the local memory control registers, * (pp301-310). The test machines are not equiped with local memory, * so nothing is tested. Only a single row seems to be supported. */ #define DRAM_ROW_TYPE 0x3000 #define DRAM_ROW_0 0x01 #define DRAM_ROW_0_SDRAM 0x01 #define DRAM_ROW_0_EMPTY 0x00 #define DRAM_ROW_CNTL_LO 0x3001 #define DRAM_PAGE_MODE_CTRL 0x10 #define DRAM_RAS_TO_CAS_OVRIDE 0x08 #define DRAM_CAS_LATENCY 0x04 #define DRAM_RAS_TIMING 0x02 #define DRAM_RAS_PRECHARGE 0x01 #define DRAM_ROW_CNTL_HI 0x3002 #define DRAM_REFRESH_RATE 0x18 #define DRAM_REFRESH_DISABLE 0x00 #define DRAM_REFRESH_60HZ 0x08 #define DRAM_REFRESH_FAST_TEST 0x10 #define DRAM_REFRESH_RESERVED 0x18 #define DRAM_SMS 0x07 #define DRAM_SMS_NORMAL 0x00 #define DRAM_SMS_NOP_ENABLE 0x01 #define DRAM_SMS_ABPCE 0x02 #define DRAM_SMS_MRCE 0x03 #define DRAM_SMS_CBRCE 0x04 /* p307 */ #define DPMS_SYNC_SELECT 0x5002 #define VSYNC_CNTL 0x08 #define VSYNC_ON 0x00 #define VSYNC_OFF 0x08 #define HSYNC_CNTL 0x02 #define HSYNC_ON 0x00 #define HSYNC_OFF 0x02 #define GPIOA 0x5010 #define GPIOB 0x5014 #define GPIOC 0x5018 #define GPIOD 0x501c #define GPIOE 0x5020 #define GPIOF 0x5024 #define GPIOG 0x5028 #define GPIOH 0x502c # define GPIO_CLOCK_DIR_MASK (1 << 0) # define GPIO_CLOCK_DIR_IN (0 << 1) # define GPIO_CLOCK_DIR_OUT (1 << 1) # define GPIO_CLOCK_VAL_MASK (1 << 2) # define GPIO_CLOCK_VAL_OUT (1 << 3) # define GPIO_CLOCK_VAL_IN (1 << 4) # define GPIO_CLOCK_PULLUP_DISABLE (1 << 5) # define GPIO_DATA_DIR_MASK (1 << 8) # define GPIO_DATA_DIR_IN (0 << 9) # define GPIO_DATA_DIR_OUT (1 << 9) # define GPIO_DATA_VAL_MASK (1 << 10) # define GPIO_DATA_VAL_OUT (1 << 11) # define GPIO_DATA_VAL_IN (1 << 12) # define GPIO_DATA_PULLUP_DISABLE (1 << 13) /* GMBus registers for hardware-assisted (non-bitbanging) I2C access */ #define GMBUS0 0x5100 #define GMBUS1 0x5104 #define GMBUS2 0x5108 #define GMBUS3 0x510c #define GMBUS4 0x5110 #define GMBUS5 0x5120 /* p317, 319 */ #define VCLK2_VCO_M 0x6008 /* treat as 16 bit? (includes msbs) */ #define VCLK2_VCO_N 0x600a #define VCLK2_VCO_DIV_SEL 0x6012 #define VCLK_DIVISOR_VGA0 0x6000 #define VCLK_DIVISOR_VGA1 0x6004 #define VCLK_POST_DIV 0x6010 /** Selects a post divisor of 4 instead of 2. */ # define VGA1_PD_P2_DIV_4 (1 << 15) /** Overrides the p2 post divisor field */ # define VGA1_PD_P1_DIV_2 (1 << 13) # define VGA1_PD_P1_SHIFT 8 /** P1 value is 2 greater than this field */ # define VGA1_PD_P1_MASK (0x1f << 8) /** Selects a post divisor of 4 instead of 2. */ # define VGA0_PD_P2_DIV_4 (1 << 7) /** Overrides the p2 post divisor field */ # define VGA0_PD_P1_DIV_2 (1 << 5) # define VGA0_PD_P1_SHIFT 0 /** P1 value is 2 greater than this field */ # define VGA0_PD_P1_MASK (0x1f << 0) #define POST_DIV_SELECT 0x70 #define POST_DIV_1 0x00 #define POST_DIV_2 0x10 #define POST_DIV_4 0x20 #define POST_DIV_8 0x30 #define POST_DIV_16 0x40 #define POST_DIV_32 0x50 #define VCO_LOOP_DIV_BY_4M 0x00 #define VCO_LOOP_DIV_BY_16M 0x04 /* Instruction Parser Mode Register * - p281 * - 2 new bits. */ #define INST_PM 0x20c0 #define AGP_SYNC_PACKET_FLUSH_ENABLE 0x20 /* reserved */ #define SYNC_PACKET_FLUSH_ENABLE 0x10 #define TWO_D_INST_DISABLE 0x08 #define THREE_D_INST_DISABLE 0x04 #define STATE_VAR_UPDATE_DISABLE 0x02 #define PAL_STIP_DISABLE 0x01 #define MEMMODE 0x20dc /* Instruction parser error register. p279 */ #define IPEIR 0x2088 #define IPEHR 0x208C #define INST_DONE 0x2090 #define SCPD0 0x209c /* debug */ #define INST_PS 0x20c4 #define IPEIR_I965 0x2064 /* i965 */ #define IPEHR_I965 0x2068 /* i965 */ #define INST_DONE_I965 0x206c # define I965_SF_DONE (1 << 23) # define I965_SE_DONE (1 << 22) # define I965_WM_DONE (1 << 21) # define I965_TEXTURE_FETCH_DONE (1 << 14) # define I965_SAMPLER_CACHE_DONE (1 << 12) # define I965_FILTER_DONE (1 << 11) # define I965_PS_DONE (1 << 9) # define I965_CC_DONE (1 << 8) # define I965_MAP_FILTER_DONE (1 << 7) # define I965_MAP_L2_IDLE (1 << 6) # define I965_CP_DONE (1 << 1) # define I965_RING_0_ENABLE (1 << 0) #define INST_PS_I965 0x2070 /* Current active ring head address: */ #define ACTHD 0x2074 /* Current primary/secondary DMA fetch addresses: */ #define DMA_FADD_P 0x2078 #define DMA_FADD_S 0x20d4 #define INST_DONE_1 0x207c #define CACHE_MODE_0 0x2120 #define CACHE_MODE_1 0x2124 #define MI_MODE 0x209c #define MI_DISPLAY_POWER_DOWN 0x20e0 #define MI_ARB_STATE 0x20e4 #define MI_RDRET_STATE 0x20fc /* Start addresses for each of the primary rings: */ #define PR0_STR 0x20f0 #define PR1_STR 0x20f4 #define PR2_STR 0x20f8 #define WIZ_CTL 0x7c00 #define WIZ_CTL_SINGLE_SUBSPAN (1<<6) #define WIZ_CTL_IGNORE_STALLS (1<<5) #define SVG_WORK_CTL 0x7408 #define TS_CTL 0x7e00 #define TS_MUX_ERR_CODE (0<<8) #define TS_MUX_URB_0 (1<<8) #define TS_MUX_DISPATCH_ID_0 (10<<8) #define TS_MUX_ERR_CODE_VALID (15<<8) #define TS_MUX_TID_0 (16<<8) #define TS_MUX_EUID_0 (18<<8) #define TS_MUX_FFID_0 (22<<8) #define TS_MUX_EOT (26<<8) #define TS_MUX_SIDEBAND_0 (27<<8) #define TS_SNAP_ALL_CHILD (1<<2) #define TS_SNAP_ALL_ROOT (1<<1) #define TS_SNAP_ENABLE (1<<0) #define TS_DEBUG_DATA 0x7e0c #define TD_CTL 0x8000 #define TD_CTL2 0x8004 #define ECOSKPD 0x21d0 #define EXCC 0x2028 /* I965 debug regs: */ #define IA_VERTICES_COUNT_QW 0x2310 #define IA_PRIMITIVES_COUNT_QW 0x2318 #define VS_INVOCATION_COUNT_QW 0x2320 #define GS_INVOCATION_COUNT_QW 0x2328 #define GS_PRIMITIVES_COUNT_QW 0x2330 #define CL_INVOCATION_COUNT_QW 0x2338 #define CL_PRIMITIVES_COUNT_QW 0x2340 #define PS_INVOCATION_COUNT_QW 0x2348 #define PS_DEPTH_COUNT_QW 0x2350 #define TIMESTAMP_QW 0x2358 #define CLKCMP_QW 0x2360 /* General error reporting regs, p296 */ #define EIR 0x20B0 #define EMR 0x20B4 #define ESR 0x20B8 # define ERR_VERTEX_MAX (1 << 5) /* lpt/cst */ # define ERR_PGTBL_ERROR (1 << 4) # define ERR_DISPLAY_OVERLAY_UNDERRUN (1 << 3) # define ERR_MAIN_MEMORY_REFRESH (1 << 1) # define ERR_INSTRUCTION_ERROR (1 << 0) /* Interrupt Control Registers * - new bits for i810 * - new register hwstam (mask) */ #define HWSTAM 0x2098 /* p290 */ #define IER 0x20a0 /* p291 */ #define IIR 0x20a4 /* p292 */ #define IMR 0x20a8 /* p293 */ #define ISR 0x20ac /* p294 */ #define HW_ERROR 0x8000 #define SYNC_STATUS_TOGGLE 0x1000 #define DPY_0_FLIP_PENDING 0x0800 #define DPY_1_FLIP_PENDING 0x0400 /* not implemented on i810 */ #define OVL_0_FLIP_PENDING 0x0200 #define OVL_1_FLIP_PENDING 0x0100 /* not implemented on i810 */ #define DPY_0_VBLANK 0x0080 #define DPY_0_EVENT 0x0040 #define DPY_1_VBLANK 0x0020 /* not implemented on i810 */ #define DPY_1_EVENT 0x0010 /* not implemented on i810 */ #define HOST_PORT_EVENT 0x0008 /* */ #define CAPTURE_EVENT 0x0004 /* */ #define USER_DEFINED 0x0002 #define BREAKPOINT 0x0001 #define INTR_RESERVED (0x6000 | \ DPY_1_FLIP_PENDING | \ OVL_1_FLIP_PENDING | \ DPY_1_VBLANK | \ DPY_1_EVENT | \ HOST_PORT_EVENT | \ CAPTURE_EVENT ) /* FIFO Watermark and Burst Length Control Register * * - different offset and contents on i810 (p299) (fewer bits per field) * - some overlay fields added * - what does it all mean? */ #define FWATER_BLC 0x20d8 #define FWATER_BLC2 0x20dc #define MM_BURST_LENGTH 0x00700000 #define MM_FIFO_WATERMARK 0x0001F000 #define LM_BURST_LENGTH 0x00000700 #define LM_FIFO_WATERMARK 0x0000001F /* Fence/Tiling ranges [0..7] */ #define FENCE 0x2000 #define FENCE_NR 8 #define FENCE_NEW 0x3000 #define FENCE_NEW_NR 16 #define FENCE_LINEAR 0 #define FENCE_XMAJOR 1 #define FENCE_YMAJOR 2 #define I915G_FENCE_START_MASK 0x0ff00000 #define I830_FENCE_START_MASK 0x07f80000 #define FENCE_START_MASK 0x03F80000 #define FENCE_X_MAJOR 0x00000000 #define FENCE_Y_MAJOR 0x00001000 #define FENCE_SIZE_MASK 0x00000700 #define FENCE_SIZE_512K 0x00000000 #define FENCE_SIZE_1M 0x00000100 #define FENCE_SIZE_2M 0x00000200 #define FENCE_SIZE_4M 0x00000300 #define FENCE_SIZE_8M 0x00000400 #define FENCE_SIZE_16M 0x00000500 #define FENCE_SIZE_32M 0x00000600 #define FENCE_SIZE_64M 0x00000700 #define I915G_FENCE_SIZE_1M 0x00000000 #define I915G_FENCE_SIZE_2M 0x00000100 #define I915G_FENCE_SIZE_4M 0x00000200 #define I915G_FENCE_SIZE_8M 0x00000300 #define I915G_FENCE_SIZE_16M 0x00000400 #define I915G_FENCE_SIZE_32M 0x00000500 #define I915G_FENCE_SIZE_64M 0x00000600 #define I915G_FENCE_SIZE_128M 0x00000700 #define I965_FENCE_X_MAJOR 0x00000000 #define I965_FENCE_Y_MAJOR 0x00000002 #define FENCE_PITCH_1 0x00000000 #define FENCE_PITCH_2 0x00000010 #define FENCE_PITCH_4 0x00000020 #define FENCE_PITCH_8 0x00000030 #define FENCE_PITCH_16 0x00000040 #define FENCE_PITCH_32 0x00000050 #define FENCE_PITCH_64 0x00000060 #define FENCE_VALID 0x00000001 /* Registers to control page table, p274 */ #define PGETBL_CTL 0x2020 #define PGETBL_ADDR_MASK 0xFFFFF000 #define PGETBL_ENABLE_MASK 0x00000001 #define PGETBL_ENABLED 0x00000001 /** Added in 965G, this field has the actual size of the global GTT */ #define PGETBL_SIZE_MASK 0x0000000e #define PGETBL_SIZE_512KB (0 << 1) #define PGETBL_SIZE_256KB (1 << 1) #define PGETBL_SIZE_128KB (2 << 1) #define PGETBL_SIZE_1MB (3 << 1) #define PGETBL_SIZE_2MB (4 << 1) #define PGETBL_SIZE_1_5MB (5 << 1) #define G33_PGETBL_SIZE_MASK (3 << 8) #define G33_PGETBL_SIZE_1M (1 << 8) #define G33_PGETBL_SIZE_2M (2 << 8) #define I830_PTE_BASE 0x10000 #define PTE_ADDRESS_MASK 0xfffff000 #define PTE_ADDRESS_MASK_HIGH 0x000000f0 /* i915+ */ #define PTE_MAPPING_TYPE_UNCACHED (0 << 1) #define PTE_MAPPING_TYPE_DCACHE (1 << 1) /* i830 only */ #define PTE_MAPPING_TYPE_CACHED (3 << 1) #define PTE_MAPPING_TYPE_MASK (3 << 1) #define PTE_VALID (1 << 0) /** @defgroup PGE_ERR * @{ */ /** Page table debug register for i845 */ #define PGE_ERR 0x2024 #define PGE_ERR_ADDR_MASK 0xFFFFF000 #define PGE_ERR_ID_MASK 0x00000038 #define PGE_ERR_CAPTURE 0x00000000 #define PGE_ERR_OVERLAY 0x00000008 #define PGE_ERR_DISPLAY 0x00000010 #define PGE_ERR_HOST 0x00000018 #define PGE_ERR_RENDER 0x00000020 #define PGE_ERR_BLITTER 0x00000028 #define PGE_ERR_MAPPING 0x00000030 #define PGE_ERR_CMD_PARSER 0x00000038 #define PGE_ERR_TYPE_MASK 0x00000007 #define PGE_ERR_INV_TABLE 0x00000000 #define PGE_ERR_INV_PTE 0x00000001 #define PGE_ERR_MIXED_TYPES 0x00000002 #define PGE_ERR_PAGE_MISS 0x00000003 #define PGE_ERR_ILLEGAL_TRX 0x00000004 #define PGE_ERR_LOCAL_MEM 0x00000005 #define PGE_ERR_TILED 0x00000006 /** @} */ /** @defgroup PGTBL_ER * @{ */ /** Page table debug register for i945 */ # define PGTBL_ER 0x2024 # define PGTBL_ERR_MT_TILING (1 << 27) # define PGTBL_ERR_MT_GTT_PTE (1 << 26) # define PGTBL_ERR_LC_TILING (1 << 25) # define PGTBL_ERR_LC_GTT_PTE (1 << 24) # define PGTBL_ERR_BIN_VERTEXDATA_GTT_PTE (1 << 23) # define PGTBL_ERR_BIN_INSTRUCTION_GTT_PTE (1 << 22) # define PGTBL_ERR_CS_VERTEXDATA_GTT_PTE (1 << 21) # define PGTBL_ERR_CS_INSTRUCTION_GTT_PTE (1 << 20) # define PGTBL_ERR_CS_GTT (1 << 19) # define PGTBL_ERR_OVERLAY_TILING (1 << 18) # define PGTBL_ERR_OVERLAY_GTT_PTE (1 << 16) # define PGTBL_ERR_DISPC_TILING (1 << 14) # define PGTBL_ERR_DISPC_GTT_PTE (1 << 12) # define PGTBL_ERR_DISPB_TILING (1 << 10) # define PGTBL_ERR_DISPB_GTT_PTE (1 << 8) # define PGTBL_ERR_DISPA_TILING (1 << 6) # define PGTBL_ERR_DISPA_GTT_PTE (1 << 4) # define PGTBL_ERR_HOST_PTE_DATA (1 << 1) # define PGTBL_ERR_HOST_GTT_PTE (1 << 0) /** @} */ /* Ring buffer registers, p277, overview p19 */ #define LP_RING 0x2030 #define HP_RING 0x2040 #define RING_TAIL 0x00 #define TAIL_ADDR 0x000FFFF8 #define I830_TAIL_MASK 0x001FFFF8 #define RING_HEAD 0x04 #define HEAD_WRAP_COUNT 0xFFE00000 #define HEAD_WRAP_ONE 0x00200000 #define HEAD_ADDR 0x001FFFFC #define I830_HEAD_MASK 0x001FFFFC #define RING_START 0x08 #define START_ADDR 0x03FFFFF8 #define I830_RING_START_MASK 0xFFFFF000 #define RING_LEN 0x0C #define RING_NR_PAGES 0x001FF000 #define I830_RING_NR_PAGES 0x001FF000 #define RING_REPORT_MASK 0x00000006 #define RING_REPORT_64K 0x00000002 #define RING_REPORT_128K 0x00000004 #define RING_NO_REPORT 0x00000000 #define RING_VALID_MASK 0x00000001 #define RING_VALID 0x00000001 #define RING_INVALID 0x00000000 /* BitBlt Instructions * * There are many more masks & ranges yet to add. */ #define BR00_BITBLT_CLIENT 0x40000000 #define BR00_OP_COLOR_BLT 0x10000000 #define BR00_OP_SRC_COPY_BLT 0x10C00000 #define BR00_OP_FULL_BLT 0x11400000 #define BR00_OP_MONO_SRC_BLT 0x11800000 #define BR00_OP_MONO_SRC_COPY_BLT 0x11000000 #define BR00_OP_MONO_PAT_BLT 0x11C00000 #define BR00_OP_MONO_SRC_COPY_IMMEDIATE_BLT (0x61 << 22) #define BR00_OP_TEXT_IMMEDIATE_BLT 0xc000000 #define BR00_TPCY_DISABLE 0x00000000 #define BR00_TPCY_ENABLE 0x00000010 #define BR00_TPCY_ROP 0x00000000 #define BR00_TPCY_NO_ROP 0x00000020 #define BR00_TPCY_EQ 0x00000000 #define BR00_TPCY_NOT_EQ 0x00000040 #define BR00_PAT_MSB_FIRST 0x00000000 /* ? */ #define BR00_PAT_VERT_ALIGN 0x000000e0 #define BR00_LENGTH 0x0000000F #define BR09_DEST_ADDR 0x03FFFFFF #define BR11_SOURCE_PITCH 0x00003FFF #define BR12_SOURCE_ADDR 0x03FFFFFF #define BR13_SOLID_PATTERN 0x80000000 #define BR13_RIGHT_TO_LEFT 0x40000000 #define BR13_LEFT_TO_RIGHT 0x00000000 #define BR13_MONO_TRANSPCY 0x20000000 #define BR13_MONO_PATN_TRANS 0x10000000 #define BR13_USE_DYN_DEPTH 0x04000000 #define BR13_DYN_8BPP 0x00000000 #define BR13_DYN_16BPP 0x01000000 #define BR13_DYN_24BPP 0x02000000 #define BR13_ROP_MASK 0x00FF0000 #define BR13_DEST_PITCH 0x0000FFFF #define BR13_PITCH_SIGN_BIT 0x00008000 #define BR14_DEST_HEIGHT 0xFFFF0000 #define BR14_DEST_WIDTH 0x0000FFFF #define BR15_PATTERN_ADDR 0x03FFFFFF #define BR16_SOLID_PAT_COLOR 0x00FFFFFF #define BR16_BACKGND_PAT_CLR 0x00FFFFFF #define BR17_FGND_PAT_CLR 0x00FFFFFF #define BR18_SRC_BGND_CLR 0x00FFFFFF #define BR19_SRC_FGND_CLR 0x00FFFFFF /* Instruction parser instructions */ #define INST_PARSER_CLIENT 0x00000000 #define INST_OP_FLUSH 0x02000000 #define INST_FLUSH_MAP_CACHE 0x00000001 #define GFX_OP_USER_INTERRUPT ((0<<29)|(2<<23)) /* Registers in the i810 host-pci bridge pci config space which affect * the i810 graphics operations. */ #define SMRAM_MISCC 0x70 #define GMS 0x000000c0 #define GMS_DISABLE 0x00000000 #define GMS_ENABLE_BARE 0x00000040 #define GMS_ENABLE_512K 0x00000080 #define GMS_ENABLE_1M 0x000000c0 #define USMM 0x00000030 #define USMM_DISABLE 0x00000000 #define USMM_TSEG_ZERO 0x00000010 #define USMM_TSEG_512K 0x00000020 #define USMM_TSEG_1M 0x00000030 #define GFX_MEM_WIN_SIZE 0x00010000 #define GFX_MEM_WIN_32M 0x00010000 #define GFX_MEM_WIN_64M 0x00000000 /* Overkill? I don't know. Need to figure out top of mem to make the * SMRAM calculations come out. Linux seems to have problems * detecting it all on its own, so this seems a reasonable double * check to any user supplied 'mem=...' boot param. * * ... unfortunately this reg doesn't work according to spec on the * test hardware. */ #define WHTCFG_PAMR_DRP 0x50 #define SYS_DRAM_ROW_0_SHIFT 16 #define SYS_DRAM_ROW_1_SHIFT 20 #define DRAM_MASK 0x0f #define DRAM_VALUE_0 0 #define DRAM_VALUE_1 8 /* No 2 value defined */ #define DRAM_VALUE_3 16 #define DRAM_VALUE_4 16 #define DRAM_VALUE_5 24 #define DRAM_VALUE_6 32 #define DRAM_VALUE_7 32 #define DRAM_VALUE_8 48 #define DRAM_VALUE_9 64 #define DRAM_VALUE_A 64 #define DRAM_VALUE_B 96 #define DRAM_VALUE_C 128 #define DRAM_VALUE_D 128 #define DRAM_VALUE_E 192 #define DRAM_VALUE_F 256 /* nice one, geezer */ #define LM_FREQ_MASK 0x10 #define LM_FREQ_133 0x10 #define LM_FREQ_100 0x00 /* These are 3d state registers, but the state is invarient, so we let * the X server handle it: */ /* GFXRENDERSTATE_COLOR_CHROMA_KEY, p135 */ #define GFX_OP_COLOR_CHROMA_KEY ((0x3<<29)|(0x1d<<24)|(0x2<<16)|0x1) #define CC1_UPDATE_KILL_WRITE (1<<28) #define CC1_ENABLE_KILL_WRITE (1<<27) #define CC1_DISABLE_KILL_WRITE 0 #define CC1_UPDATE_COLOR_IDX (1<<26) #define CC1_UPDATE_CHROMA_LOW (1<<25) #define CC1_UPDATE_CHROMA_HI (1<<24) #define CC1_CHROMA_LOW_MASK ((1<<24)-1) #define CC2_COLOR_IDX_SHIFT 24 #define CC2_COLOR_IDX_MASK (0xff<<24) #define CC2_CHROMA_HI_MASK ((1<<24)-1) #define GFX_CMD_CONTEXT_SEL ((0<<29)|(0x5<<23)) #define CS_UPDATE_LOAD (1<<17) #define CS_UPDATE_USE (1<<16) #define CS_UPDATE_LOAD (1<<17) #define CS_LOAD_CTX0 0 #define CS_LOAD_CTX1 (1<<8) #define CS_USE_CTX0 0 #define CS_USE_CTX1 (1<<0) /* I810 LCD/TV registers */ #define LCD_TV_HTOTAL 0x60000 #define LCD_TV_C 0x60018 #define LCD_TV_OVRACT 0x6001C #define LCD_TV_ENABLE (1 << 31) #define LCD_TV_VGAMOD (1 << 28) /* I830 CRTC registers */ #define HTOTAL_A 0x60000 #define HBLANK_A 0x60004 #define HSYNC_A 0x60008 #define VTOTAL_A 0x6000c #define VBLANK_A 0x60010 #define VSYNC_A 0x60014 #define PIPEASRC 0x6001c #define BCLRPAT_A 0x60020 #define VSYNCSHIFT_A 0x60028 #define HTOTAL_B 0x61000 #define HBLANK_B 0x61004 #define HSYNC_B 0x61008 #define VTOTAL_B 0x6100c #define VBLANK_B 0x61010 #define VSYNC_B 0x61014 #define PIPEBSRC 0x6101c #define BCLRPAT_B 0x61020 #define VSYNCSHIFT_B 0x61028 #define PP_STATUS 0x61200 # define PP_ON (1 << 31) /** * Indicates that all dependencies of the panel are on: * * - PLL enabled * - pipe enabled * - LVDS/DVOB/DVOC on */ # define PP_READY (1 << 30) # define PP_SEQUENCE_NONE (0 << 28) # define PP_SEQUENCE_ON (1 << 28) # define PP_SEQUENCE_OFF (2 << 28) # define PP_SEQUENCE_MASK 0x30000000 #define PP_CONTROL 0x61204 # define POWER_DOWN_ON_RESET (1 << 1) # define POWER_TARGET_ON (1 << 0) #define LVDSPP_ON 0x61208 #define LVDSPP_OFF 0x6120c #define PP_CYCLE 0x61210 #define PFIT_CONTROL 0x61230 # define PFIT_ENABLE (1 << 31) # define PFIT_PIPE_MASK (3 << 29) # define PFIT_PIPE_SHIFT 29 # define VERT_INTERP_DISABLE (0 << 10) # define VERT_INTERP_BILINEAR (1 << 10) # define VERT_INTERP_MASK (3 << 10) # define VERT_AUTO_SCALE (1 << 9) # define HORIZ_INTERP_DISABLE (0 << 6) # define HORIZ_INTERP_BILINEAR (1 << 6) # define HORIZ_INTERP_MASK (3 << 6) # define HORIZ_AUTO_SCALE (1 << 5) # define PANEL_8TO6_DITHER_ENABLE (1 << 3) #define PFIT_PGM_RATIOS 0x61234 # define PFIT_VERT_SCALE_MASK 0xfff00000 # define PFIT_HORIZ_SCALE_MASK 0x0000fff0 #define PFIT_AUTO_RATIOS 0x61238 #define DPLL_A 0x06014 #define DPLL_B 0x06018 # define DPLL_VCO_ENABLE (1 << 31) # define DPLL_DVO_HIGH_SPEED (1 << 30) # define DPLL_SYNCLOCK_ENABLE (1 << 29) # define DPLL_VGA_MODE_DIS (1 << 28) # define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */ # define DPLLB_MODE_LVDS (2 << 26) /* i915 */ # define DPLL_MODE_MASK (3 << 26) # define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */ # define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */ # define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */ # define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */ # define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */ # define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */ /** * The i830 generation, in DAC/serial mode, defines p1 as two plus this * bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set. */ # define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000 /** * The i830 generation, in LVDS mode, defines P1 as the bit number set within * this field (only one bit may be set). */ # define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000 # define DPLL_FPA01_P1_POST_DIV_SHIFT 16 # define PLL_P2_DIVIDE_BY_4 (1 << 23) /* i830, required in DVO non-gang */ # define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */ # define PLL_REF_INPUT_DREFCLK (0 << 13) # define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */ # define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO TVCLKIN */ # define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13) # define PLL_REF_INPUT_MASK (3 << 13) # define PLL_LOAD_PULSE_PHASE_SHIFT 9 /* * Parallel to Serial Load Pulse phase selection. * Selects the phase for the 10X DPLL clock for the PCIe * digital display port. The range is 4 to 13; 10 or more * is just a flip delay. The default is 6 */ # define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT) # define DISPLAY_RATE_SELECT_FPA1 (1 << 8) /** * SDVO multiplier for 945G/GM. Not used on 965. * * \sa DPLL_MD_UDI_MULTIPLIER_MASK */ # define SDVO_MULTIPLIER_MASK 0x000000ff # define SDVO_MULTIPLIER_SHIFT_HIRES 4 # define SDVO_MULTIPLIER_SHIFT_VGA 0 /** @defgroup DPLL_MD * @{ */ /** Pipe A SDVO/UDI clock multiplier/divider register for G965. */ #define DPLL_A_MD 0x0601c /** Pipe B SDVO/UDI clock multiplier/divider register for G965. */ #define DPLL_B_MD 0x06020 /** * UDI pixel divider, controlling how many pixels are stuffed into a packet. * * Value is pixels minus 1. Must be set to 1 pixel for SDVO. */ # define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000 # define DPLL_MD_UDI_DIVIDER_SHIFT 24 /** UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */ # define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000 # define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16 /** * SDVO/UDI pixel multiplier. * * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus * clock rate is 10 times the DPLL clock. At low resolution/refresh rate * modes, the bus rate would be below the limits, so SDVO allows for stuffing * dummy bytes in the datastream at an increased clock rate, with both sides of * the link knowing how many bytes are fill. * * So, for a mode with a dotclock of 65Mhz, we would want to double the clock * rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be * set to 130Mhz, and the SDVO multiplier set to 2x in this register and * through an SDVO command. * * This register field has values of multiplication factor minus 1, with * a maximum multiplier of 5 for SDVO. */ # define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00 # define DPLL_MD_UDI_MULTIPLIER_SHIFT 8 /** SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK. * This best be set to the default value (3) or the CRT won't work. No, * I don't entirely understand what this does... */ # define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f # define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0 /** @} */ #define DPLL_TEST 0x606c # define DPLLB_TEST_SDVO_DIV_1 (0 << 22) # define DPLLB_TEST_SDVO_DIV_2 (1 << 22) # define DPLLB_TEST_SDVO_DIV_4 (2 << 22) # define DPLLB_TEST_SDVO_DIV_MASK (3 << 22) # define DPLLB_TEST_N_BYPASS (1 << 19) # define DPLLB_TEST_M_BYPASS (1 << 18) # define DPLLB_INPUT_BUFFER_ENABLE (1 << 16) # define DPLLA_TEST_N_BYPASS (1 << 3) # define DPLLA_TEST_M_BYPASS (1 << 2) # define DPLLA_INPUT_BUFFER_ENABLE (1 << 0) #define D_STATE 0x6104 #define DSPCLK_GATE_D 0x6200 # define DPUNIT_B_CLOCK_GATE_DISABLE (1 << 30) /* 965 */ # define VSUNIT_CLOCK_GATE_DISABLE (1 << 29) /* 965 */ # define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* 965 */ # define VRDUNIT_CLOCK_GATE_DISABLE (1 << 27) /* 965 */ # define AUDUNIT_CLOCK_GATE_DISABLE (1 << 26) /* 965 */ # define DPUNIT_A_CLOCK_GATE_DISABLE (1 << 25) /* 965 */ # define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24) /* 965 */ # define TVRUNIT_CLOCK_GATE_DISABLE (1 << 23) /* 915-945 */ # define TVCUNIT_CLOCK_GATE_DISABLE (1 << 22) /* 915-945 */ # define TVFUNIT_CLOCK_GATE_DISABLE (1 << 21) /* 915-945 */ # define TVEUNIT_CLOCK_GATE_DISABLE (1 << 20) /* 915-945 */ # define DVSUNIT_CLOCK_GATE_DISABLE (1 << 19) /* 915-945 */ # define DSSUNIT_CLOCK_GATE_DISABLE (1 << 18) /* 915-945 */ # define DDBUNIT_CLOCK_GATE_DISABLE (1 << 17) /* 915-945 */ # define DPRUNIT_CLOCK_GATE_DISABLE (1 << 16) /* 915-945 */ # define DPFUNIT_CLOCK_GATE_DISABLE (1 << 15) /* 915-945 */ # define DPBMUNIT_CLOCK_GATE_DISABLE (1 << 14) /* 915-945 */ # define DPLSUNIT_CLOCK_GATE_DISABLE (1 << 13) /* 915-945 */ # define DPLUNIT_CLOCK_GATE_DISABLE (1 << 12) /* 915-945 */ # define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11) # define DPBUNIT_CLOCK_GATE_DISABLE (1 << 10) # define DCUNIT_CLOCK_GATE_DISABLE (1 << 9) # define DPUNIT_CLOCK_GATE_DISABLE (1 << 8) # define VRUNIT_CLOCK_GATE_DISABLE (1 << 7) /* 915+: reserved */ # define OVHUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 830-865 */ # define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 915-945 */ # define OVFUNIT_CLOCK_GATE_DISABLE (1 << 5) # define OVBUNIT_CLOCK_GATE_DISABLE (1 << 4) /** * This bit must be set on the 830 to prevent hangs when turning off the * overlay scaler. */ # define OVRUNIT_CLOCK_GATE_DISABLE (1 << 3) # define OVCUNIT_CLOCK_GATE_DISABLE (1 << 2) # define OVUUNIT_CLOCK_GATE_DISABLE (1 << 1) # define ZVUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 830 */ # define OVLUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 845,865 */ #define RENCLK_GATE_D1 0x6204 # define BLITTER_CLOCK_GATE_DISABLE (1 << 13) /* 945GM only */ # define MPEG_CLOCK_GATE_DISABLE (1 << 12) /* 945GM only */ # define PC_FE_CLOCK_GATE_DISABLE (1 << 11) # define PC_BE_CLOCK_GATE_DISABLE (1 << 10) # define WINDOWER_CLOCK_GATE_DISABLE (1 << 9) # define INTERPOLATOR_CLOCK_GATE_DISABLE (1 << 8) # define COLOR_CALCULATOR_CLOCK_GATE_DISABLE (1 << 7) # define MOTION_COMP_CLOCK_GATE_DISABLE (1 << 6) # define MAG_CLOCK_GATE_DISABLE (1 << 5) /** This bit must be unset on 855,865 */ # define MECI_CLOCK_GATE_DISABLE (1 << 4) # define DCMP_CLOCK_GATE_DISABLE (1 << 3) # define MEC_CLOCK_GATE_DISABLE (1 << 2) # define MECO_CLOCK_GATE_DISABLE (1 << 1) /** This bit must be set on 855,865. */ # define SV_CLOCK_GATE_DISABLE (1 << 0) # define I915_MPEG_CLOCK_GATE_DISABLE (1 << 16) # define I915_VLD_IP_PR_CLOCK_GATE_DISABLE (1 << 15) # define I915_MOTION_COMP_CLOCK_GATE_DISABLE (1 << 14) # define I915_BD_BF_CLOCK_GATE_DISABLE (1 << 13) # define I915_SF_SE_CLOCK_GATE_DISABLE (1 << 12) # define I915_WM_CLOCK_GATE_DISABLE (1 << 11) # define I915_IZ_CLOCK_GATE_DISABLE (1 << 10) # define I915_PI_CLOCK_GATE_DISABLE (1 << 9) # define I915_DI_CLOCK_GATE_DISABLE (1 << 8) # define I915_SH_SV_CLOCK_GATE_DISABLE (1 << 7) # define I915_PL_DG_QC_FT_CLOCK_GATE_DISABLE (1 << 6) # define I915_SC_CLOCK_GATE_DISABLE (1 << 5) # define I915_FL_CLOCK_GATE_DISABLE (1 << 4) # define I915_DM_CLOCK_GATE_DISABLE (1 << 3) # define I915_PS_CLOCK_GATE_DISABLE (1 << 2) # define I915_CC_CLOCK_GATE_DISABLE (1 << 1) # define I915_BY_CLOCK_GATE_DISABLE (1 << 0) # define I965_RCZ_CLOCK_GATE_DISABLE (1 << 30) /** This bit must always be set on 965G/965GM */ # define I965_RCC_CLOCK_GATE_DISABLE (1 << 29) # define I965_RCPB_CLOCK_GATE_DISABLE (1 << 28) # define I965_DAP_CLOCK_GATE_DISABLE (1 << 27) # define I965_ROC_CLOCK_GATE_DISABLE (1 << 26) # define I965_GW_CLOCK_GATE_DISABLE (1 << 25) # define I965_TD_CLOCK_GATE_DISABLE (1 << 24) /** This bit must always be set on 965G */ # define I965_ISC_CLOCK_GATE_DISABLE (1 << 23) # define I965_IC_CLOCK_GATE_DISABLE (1 << 22) # define I965_EU_CLOCK_GATE_DISABLE (1 << 21) # define I965_IF_CLOCK_GATE_DISABLE (1 << 20) # define I965_TC_CLOCK_GATE_DISABLE (1 << 19) # define I965_SO_CLOCK_GATE_DISABLE (1 << 17) # define I965_FBC_CLOCK_GATE_DISABLE (1 << 16) # define I965_MARI_CLOCK_GATE_DISABLE (1 << 15) # define I965_MASF_CLOCK_GATE_DISABLE (1 << 14) # define I965_MAWB_CLOCK_GATE_DISABLE (1 << 13) # define I965_EM_CLOCK_GATE_DISABLE (1 << 12) # define I965_UC_CLOCK_GATE_DISABLE (1 << 11) # define I965_SI_CLOCK_GATE_DISABLE (1 << 6) # define I965_MT_CLOCK_GATE_DISABLE (1 << 5) # define I965_PL_CLOCK_GATE_DISABLE (1 << 4) # define I965_DG_CLOCK_GATE_DISABLE (1 << 3) # define I965_QC_CLOCK_GATE_DISABLE (1 << 2) # define I965_FT_CLOCK_GATE_DISABLE (1 << 1) # define I965_DM_CLOCK_GATE_DISABLE (1 << 0) #define RENCLK_GATE_D2 0x6208 #define RAMCLK_GATE_D 0x6210 /* CRL only */ /* * This is a PCI config space register to manipulate backlight brightness * It is used when the BLM_LEGACY_MODE is turned on. When enabled, the first * byte of this config register sets brightness within the range from * 0 to 0xff */ #define LEGACY_BACKLIGHT_BRIGHTNESS 0xf4 #define BLC_PWM_CTL 0x61254 #define BACKLIGHT_MODULATION_FREQ_SHIFT (17) #define BACKLIGHT_MODULATION_FREQ_SHIFT2 (16) /** * This is the most significant 15 bits of the number of backlight cycles in a * complete cycle of the modulated backlight control. * * The actual value is this field multiplied by two. */ #define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17) #define BACKLIGHT_MODULATION_FREQ_MASK2 (0xffff << 16) #define BLM_LEGACY_MODE (1 << 16) /** * This is the number of cycles out of the backlight modulation cycle for which * the backlight is on. * * This field must be no greater than the number of cycles in the complete * backlight modulation cycle. */ #define BACKLIGHT_DUTY_CYCLE_SHIFT (0) #define BACKLIGHT_DUTY_CYCLE_MASK (0xffff) /* On 965+ backlight control is in another register */ #define BLC_PWM_CTL2 0x61250 #define BLM_LEGACY_MODE2 (1 << 30) #define BLM_CTL 0x61260 #define BLM_THRESHOLD_0 0x61270 #define BLM_THRESHOLD_1 0x61274 #define BLM_THRESHOLD_2 0x61278 #define BLM_THRESHOLD_3 0x6127c #define BLM_THRESHOLD_4 0x61280 #define BLM_THRESHOLD_5 0x61284 #define BLM_ACCUMULATOR_0 0x61290 #define BLM_ACCUMULATOR_1 0x61294 #define BLM_ACCUMULATOR_2 0x61298 #define BLM_ACCUMULATOR_3 0x6129c #define BLM_ACCUMULATOR_4 0x612a0 #define BLM_ACCUMULATOR_5 0x612a4 #define FPA0 0x06040 #define FPA1 0x06044 #define FPB0 0x06048 #define FPB1 0x0604c # define FP_N_DIV_MASK 0x003f0000 # define FP_N_DIV_SHIFT 16 # define FP_M1_DIV_MASK 0x00003f00 # define FP_M1_DIV_SHIFT 8 # define FP_M2_DIV_MASK 0x0000003f # define FP_M2_DIV_SHIFT 0 #define PORT_HOTPLUG_EN 0x61110 # define SDVOB_HOTPLUG_INT_EN (1 << 26) # define SDVOC_HOTPLUG_INT_EN (1 << 25) # define TV_HOTPLUG_INT_EN (1 << 18) # define CRT_HOTPLUG_INT_EN (1 << 9) # define CRT_HOTPLUG_FORCE_DETECT (1 << 3) #define PORT_HOTPLUG_STAT 0x61114 # define CRT_HOTPLUG_INT_STATUS (1 << 11) # define TV_HOTPLUG_INT_STATUS (1 << 10) # define CRT_HOTPLUG_MONITOR_MASK (3 << 8) # define CRT_HOTPLUG_MONITOR_COLOR (3 << 8) # define CRT_HOTPLUG_MONITOR_MONO (2 << 8) # define CRT_HOTPLUG_MONITOR_NONE (0 << 8) # define SDVOC_HOTPLUG_INT_STATUS (1 << 7) # define SDVOB_HOTPLUG_INT_STATUS (1 << 6) #define SDVOB 0x61140 #define SDVOC 0x61160 #define SDVO_ENABLE (1 << 31) #define SDVO_PIPE_B_SELECT (1 << 30) #define SDVO_STALL_SELECT (1 << 29) #define SDVO_INTERRUPT_ENABLE (1 << 26) /** * 915G/GM SDVO pixel multiplier. * * Programmed value is multiplier - 1, up to 5x. * * \sa DPLL_MD_UDI_MULTIPLIER_MASK */ #define SDVO_PORT_MULTIPLY_MASK (7 << 23) #define SDVO_PORT_MULTIPLY_SHIFT 23 #define SDVO_PHASE_SELECT_MASK (15 << 19) #define SDVO_PHASE_SELECT_DEFAULT (6 << 19) #define SDVO_CLOCK_OUTPUT_INVERT (1 << 18) #define SDVOC_GANG_MODE (1 << 16) #define SDVO_BORDER_ENABLE (1 << 7) #define SDVOB_PCIE_CONCURRENCY (1 << 3) #define SDVO_DETECTED (1 << 2) /* Bits to be preserved when writing */ #define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14)) #define SDVOC_PRESERVE_MASK (1 << 17) #define UDIB_SVB_SHB_CODES 0x61144 #define UDIB_SHA_BLANK_CODES 0x61148 #define UDIB_START_END_FILL_CODES 0x6114c #define SDVOUDI 0x61150 #define I830_HTOTAL_MASK 0xfff0000 #define I830_HACTIVE_MASK 0x7ff #define I830_HBLANKEND_MASK 0xfff0000 #define I830_HBLANKSTART_MASK 0xfff #define I830_HSYNCEND_MASK 0xfff0000 #define I830_HSYNCSTART_MASK 0xfff #define I830_VTOTAL_MASK 0xfff0000 #define I830_VACTIVE_MASK 0x7ff #define I830_VBLANKEND_MASK 0xfff0000 #define I830_VBLANKSTART_MASK 0xfff #define I830_VSYNCEND_MASK 0xfff0000 #define I830_VSYNCSTART_MASK 0xfff #define I830_PIPEA_HORZ_MASK 0x7ff0000 #define I830_PIPEA_VERT_MASK 0x7ff #define ADPA 0x61100 #define ADPA_DAC_ENABLE (1<<31) #define ADPA_DAC_DISABLE 0 #define ADPA_PIPE_SELECT_MASK (1<<30) #define ADPA_PIPE_A_SELECT 0 #define ADPA_PIPE_B_SELECT (1<<30) #define ADPA_USE_VGA_HVPOLARITY (1<<15) #define ADPA_SETS_HVPOLARITY 0 #define ADPA_VSYNC_CNTL_DISABLE (1<<11) #define ADPA_VSYNC_CNTL_ENABLE 0 #define ADPA_HSYNC_CNTL_DISABLE (1<<10) #define ADPA_HSYNC_CNTL_ENABLE 0 #define ADPA_VSYNC_ACTIVE_HIGH (1<<4) #define ADPA_VSYNC_ACTIVE_LOW 0 #define ADPA_HSYNC_ACTIVE_HIGH (1<<3) #define ADPA_HSYNC_ACTIVE_LOW 0 #define DVOA 0x61120 #define DVOB 0x61140 #define DVOC 0x61160 #define DVO_ENABLE (1 << 31) #define DVO_PIPE_B_SELECT (1 << 30) #define DVO_PIPE_STALL_UNUSED (0 << 28) #define DVO_PIPE_STALL (1 << 28) #define DVO_PIPE_STALL_TV (2 << 28) #define DVO_PIPE_STALL_MASK (3 << 28) #define DVO_USE_VGA_SYNC (1 << 15) #define DVO_DATA_ORDER_I740 (0 << 14) #define DVO_DATA_ORDER_FP (1 << 14) #define DVO_VSYNC_DISABLE (1 << 11) #define DVO_HSYNC_DISABLE (1 << 10) #define DVO_VSYNC_TRISTATE (1 << 9) #define DVO_HSYNC_TRISTATE (1 << 8) #define DVO_BORDER_ENABLE (1 << 7) #define DVO_DATA_ORDER_GBRG (1 << 6) #define DVO_DATA_ORDER_RGGB (0 << 6) #define DVO_DATA_ORDER_GBRG_ERRATA (0 << 6) #define DVO_DATA_ORDER_RGGB_ERRATA (1 << 6) #define DVO_VSYNC_ACTIVE_HIGH (1 << 4) #define DVO_HSYNC_ACTIVE_HIGH (1 << 3) #define DVO_BLANK_ACTIVE_HIGH (1 << 2) #define DVO_OUTPUT_CSTATE_PIXELS (1 << 1) /* SDG only */ #define DVO_OUTPUT_SOURCE_SIZE_PIXELS (1 << 0) /* SDG only */ #define DVO_PRESERVE_MASK (0x7<<24) #define DVOA_SRCDIM 0x61124 #define DVOB_SRCDIM 0x61144 #define DVOC_SRCDIM 0x61164 #define DVO_SRCDIM_HORIZONTAL_SHIFT 12 #define DVO_SRCDIM_VERTICAL_SHIFT 0 /** @defgroup LVDS * @{ */ /** * This register controls the LVDS output enable, pipe selection, and data * format selection. * * All of the clock/data pairs are force powered down by power sequencing. */ #define LVDS 0x61180 /** * Enables the LVDS port. This bit must be set before DPLLs are enabled, as * the DPLL semantics change when the LVDS is assigned to that pipe. */ # define LVDS_PORT_EN (1 << 31) /** Selects pipe B for LVDS data. Must be set on pre-965. */ # define LVDS_PIPEB_SELECT (1 << 30) /* on 965, dithering is enabled in this register, not PFIT_CONTROL */ # define LVDS_DITHER_ENABLE (1 << 25) /* * Selects between .0 and .1 formats: * * 0 = 1x18.0, 2x18.0, 1x24.0 or 2x24.0 * 1 = 1x24.1 or 2x24.1 */ # define LVDS_DATA_FORMAT_DOT_ONE (1 << 24) /* Using LE instead of HS on second channel control signal */ # define LVDS_LE_CONTROL_ENABLE (1 << 23) /* Using LF instead of VS on second channel control signal */ # define LVDS_LF_CONTROL_ENABLE (1 << 22) /* invert vsync signal polarity */ # define LVDS_VSYNC_POLARITY_INVERT (1 << 21) /* invert hsync signal polarity */ # define LVDS_HSYNC_POLARITY_INVERT (1 << 20) /* invert display enable signal polarity */ # define LVDS_DE_POLARITY_INVERT (1 << 19) /* * Control signals for second channel, ignored in single channel modes */ /* send DE, HS, VS on second channel */ # define LVDS_SECOND_CHANNEL_DE_HS_VS (0 << 17) # define LVDS_SECOND_CHANNEL_RESERVED (1 << 17) /* Send zeros instead of DE, HS, VS on second channel */ # define LVDS_SECOND_CHANNEL_ZEROS (2 << 17) /* Set DE=0, HS=LE, VS=LF on second channel */ # define LVDS_SECOND_CHANNEL_HS_VS (3 << 17) /* * Send duplicate data for channel reserved bits, otherwise send zeros */ # define LVDS_CHANNEL_DUP_RESERVED (1 << 16) /* * Enable border for unscaled (or aspect-scaled) display */ # define LVDS_BORDER_ENABLE (1 << 15) /* * Tri-state the LVDS buffers when powered down, otherwise * they are set to 0V */ # define LVDS_POWER_DOWN_TRI_STATE (1 << 10) /** * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per * pixel. */ # define LVDS_A0A2_CLKA_POWER_MASK (3 << 8) # define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8) # define LVDS_A0A2_CLKA_POWER_UP (3 << 8) /** * Controls the A3 data pair, which contains the additional LSBs for 24 bit * mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be * on. */ # define LVDS_A3_POWER_MASK (3 << 6) # define LVDS_A3_POWER_DOWN (0 << 6) # define LVDS_A3_POWER_UP (3 << 6) /** * Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP * is set. */ # define LVDS_CLKB_POWER_MASK (3 << 4) # define LVDS_CLKB_POWER_DOWN (0 << 4) # define LVDS_CLKB_POWER_UP (3 << 4) /** * Controls the B0-B3 data pairs. This must be set to match the DPLL p2 * setting for whether we are in dual-channel mode. The B3 pair will * additionally only be powered up when LVDS_A3_POWER_UP is set. */ # define LVDS_B0B3_POWER_MASK (3 << 2) # define LVDS_B0B3_POWER_DOWN (0 << 2) # define LVDS_B0B3_POWER_UP (3 << 2) /** @} */ /* * Two channel clock control. Turn this on if you need clkb for two channel mode * Overridden by global LVDS power sequencing */ /* clkb off */ # define LVDS_CLKB_POWER_DOWN (0 << 4) /* powered up, but clkb forced to 0 */ # define LVDS_CLKB_POWER_PARTIAL (1 << 4) /* clock B running */ # define LVDS_CLKB_POWER_UP (3 << 4) /* * Two channel mode B0-B2 control. Sets state when power is on. * Set to POWER_DOWN in single channel mode, other settings enable * two channel mode. The CLKB power control controls whether that clock * is enabled during two channel mode. * */ /* Everything is off, including B3 and CLKB */ # define LVDS_B_POWER_DOWN (0 << 2) /* B0, B1, B2 and data lines forced to 0. timing is active */ # define LVDS_B_POWER_PARTIAL (1 << 2) /* data lines active (both timing and colour) */ # define LVDS_B_POWER_UP (3 << 2) /** @defgroup TV_CTL * @{ */ #define TV_CTL 0x68000 /** Enables the TV encoder */ # define TV_ENC_ENABLE (1 << 31) /** Sources the TV encoder input from pipe B instead of A. */ # define TV_ENC_PIPEB_SELECT (1 << 30) /** Outputs composite video (DAC A only) */ # define TV_ENC_OUTPUT_COMPOSITE (0 << 28) /** Outputs SVideo video (DAC B/C) */ # define TV_ENC_OUTPUT_SVIDEO (1 << 28) /** Outputs Component video (DAC A/B/C) */ # define TV_ENC_OUTPUT_COMPONENT (2 << 28) /** Outputs Composite and SVideo (DAC A/B/C) */ # define TV_ENC_OUTPUT_SVIDEO_COMPOSITE (3 << 28) # define TV_TRILEVEL_SYNC (1 << 21) /** Enables slow sync generation (945GM only) */ # define TV_SLOW_SYNC (1 << 20) /** Selects 4x oversampling for 480i and 576p */ # define TV_OVERSAMPLE_4X (0 << 18) /** Selects 2x oversampling for 720p and 1080i */ # define TV_OVERSAMPLE_2X (1 << 18) /** Selects no oversampling for 1080p */ # define TV_OVERSAMPLE_NONE (2 << 18) /** Selects 8x oversampling */ # define TV_OVERSAMPLE_8X (3 << 18) /** Selects progressive mode rather than interlaced */ # define TV_PROGRESSIVE (1 << 17) /** Sets the colorburst to PAL mode. Required for non-M PAL modes. */ # define TV_PAL_BURST (1 << 16) /** Field for setting delay of Y compared to C */ # define TV_YC_SKEW_MASK (7 << 12) /** Enables a fix for 480p/576p standard definition modes on the 915GM only */ # define TV_ENC_SDP_FIX (1 << 11) /** * Enables a fix for the 915GM only. * * Not sure what it does. */ # define TV_ENC_C0_FIX (1 << 10) /** Bits that must be preserved by software */ # define TV_CTL_SAVE ((3 << 8) | (3 << 6)) # define TV_FUSE_STATE_MASK (3 << 4) /** Read-only state that reports all features enabled */ # define TV_FUSE_STATE_ENABLED (0 << 4) /** Read-only state that reports that Macrovision is disabled in hardware*/ # define TV_FUSE_STATE_NO_MACROVISION (1 << 4) /** Read-only state that reports that TV-out is disabled in hardware. */ # define TV_FUSE_STATE_DISABLED (2 << 4) /** Normal operation */ # define TV_TEST_MODE_NORMAL (0 << 0) /** Encoder test pattern 1 - combo pattern */ # define TV_TEST_MODE_PATTERN_1 (1 << 0) /** Encoder test pattern 2 - full screen vertical 75% color bars */ # define TV_TEST_MODE_PATTERN_2 (2 << 0) /** Encoder test pattern 3 - full screen horizontal 75% color bars */ # define TV_TEST_MODE_PATTERN_3 (3 << 0) /** Encoder test pattern 4 - random noise */ # define TV_TEST_MODE_PATTERN_4 (4 << 0) /** Encoder test pattern 5 - linear color ramps */ # define TV_TEST_MODE_PATTERN_5 (5 << 0) /** * This test mode forces the DACs to 50% of full output. * * This is used for load detection in combination with TVDAC_SENSE_MASK */ # define TV_TEST_MODE_MONITOR_DETECT (7 << 0) # define TV_TEST_MODE_MASK (7 << 0) /** @} */ /** @defgroup TV_DAC * @{ */ #define TV_DAC 0x68004 /** * Reports that DAC state change logic has reported change (RO). * * This gets cleared when TV_DAC_STATE_EN is cleared */ # define TVDAC_STATE_CHG (1 << 31) # define TVDAC_SENSE_MASK (7 << 28) /** Reports that DAC A voltage is above the detect threshold */ # define TVDAC_A_SENSE (1 << 30) /** Reports that DAC B voltage is above the detect threshold */ # define TVDAC_B_SENSE (1 << 29) /** Reports that DAC C voltage is above the detect threshold */ # define TVDAC_C_SENSE (1 << 28) /** * Enables DAC state detection logic, for load-based TV detection. * * The PLL of the chosen pipe (in TV_CTL) must be running, and the encoder set * to off, for load detection to work. */ # define TVDAC_STATE_CHG_EN (1 << 27) /** Sets the DAC A sense value to high */ # define TVDAC_A_SENSE_CTL (1 << 26) /** Sets the DAC B sense value to high */ # define TVDAC_B_SENSE_CTL (1 << 25) /** Sets the DAC C sense value to high */ # define TVDAC_C_SENSE_CTL (1 << 24) /** Overrides the ENC_ENABLE and DAC voltage levels */ # define DAC_CTL_OVERRIDE (1 << 7) /** Sets the slew rate. Must be preserved in software */ # define ENC_TVDAC_SLEW_FAST (1 << 6) # define DAC_A_1_3_V (0 << 4) # define DAC_A_1_1_V (1 << 4) # define DAC_A_0_7_V (2 << 4) # define DAC_A_OFF (3 << 4) # define DAC_B_1_3_V (0 << 2) # define DAC_B_1_1_V (1 << 2) # define DAC_B_0_7_V (2 << 2) # define DAC_B_OFF (3 << 2) # define DAC_C_1_3_V (0 << 0) # define DAC_C_1_1_V (1 << 0) # define DAC_C_0_7_V (2 << 0) # define DAC_C_OFF (3 << 0) /** @} */ /** * CSC coefficients are stored in a floating point format with 9 bits of * mantissa and 2 or 3 bits of exponent. The exponent is represented as 2**-n, * where 2-bit exponents are unsigned n, and 3-bit exponents are signed n with * -1 (0x3) being the only legal negative value. */ #define TV_CSC_Y 0x68010 # define TV_RY_MASK 0x07ff0000 # define TV_RY_SHIFT 16 # define TV_GY_MASK 0x00000fff # define TV_GY_SHIFT 0 #define TV_CSC_Y2 0x68014 # define TV_BY_MASK 0x07ff0000 # define TV_BY_SHIFT 16 /** * Y attenuation for component video. * * Stored in 1.9 fixed point. */ # define TV_AY_MASK 0x000003ff # define TV_AY_SHIFT 0 #define TV_CSC_U 0x68018 # define TV_RU_MASK 0x07ff0000 # define TV_RU_SHIFT 16 # define TV_GU_MASK 0x000007ff # define TV_GU_SHIFT 0 #define TV_CSC_U2 0x6801c # define TV_BU_MASK 0x07ff0000 # define TV_BU_SHIFT 16 /** * U attenuation for component video. * * Stored in 1.9 fixed point. */ # define TV_AU_MASK 0x000003ff # define TV_AU_SHIFT 0 #define TV_CSC_V 0x68020 # define TV_RV_MASK 0x0fff0000 # define TV_RV_SHIFT 16 # define TV_GV_MASK 0x000007ff # define TV_GV_SHIFT 0 #define TV_CSC_V2 0x68024 # define TV_BV_MASK 0x07ff0000 # define TV_BV_SHIFT 16 /** * V attenuation for component video. * * Stored in 1.9 fixed point. */ # define TV_AV_MASK 0x000007ff # define TV_AV_SHIFT 0 /** @defgroup TV_CSC_KNOBS * @{ */ #define TV_CLR_KNOBS 0x68028 /** 2s-complement brightness adjustment */ # define TV_BRIGHTNESS_MASK 0xff000000 # define TV_BRIGHTNESS_SHIFT 24 /** Contrast adjustment, as a 2.6 unsigned floating point number */ # define TV_CONTRAST_MASK 0x00ff0000 # define TV_CONTRAST_SHIFT 16 /** Saturation adjustment, as a 2.6 unsigned floating point number */ # define TV_SATURATION_MASK 0x0000ff00 # define TV_SATURATION_SHIFT 8 /** Hue adjustment, as an integer phase angle in degrees */ # define TV_HUE_MASK 0x000000ff # define TV_HUE_SHIFT 0 /** @} */ /** @defgroup TV_CLR_LEVEL * @{ */ #define TV_CLR_LEVEL 0x6802c /** Controls the DAC level for black */ # define TV_BLACK_LEVEL_MASK 0x01ff0000 # define TV_BLACK_LEVEL_SHIFT 16 /** Controls the DAC level for blanking */ # define TV_BLANK_LEVEL_MASK 0x000001ff # define TV_BLANK_LEVEL_SHIFT 0 /* @} */ /** @defgroup TV_H_CTL_1 * @{ */ #define TV_H_CTL_1 0x68030 /** Number of pixels in the hsync. */ # define TV_HSYNC_END_MASK 0x1fff0000 # define TV_HSYNC_END_SHIFT 16 /** Total number of pixels minus one in the line (display and blanking). */ # define TV_HTOTAL_MASK 0x00001fff # define TV_HTOTAL_SHIFT 0 /** @} */ /** @defgroup TV_H_CTL_2 * @{ */ #define TV_H_CTL_2 0x68034 /** Enables the colorburst (needed for non-component color) */ # define TV_BURST_ENA (1 << 31) /** Offset of the colorburst from the start of hsync, in pixels minus one. */ # define TV_HBURST_START_SHIFT 16 # define TV_HBURST_START_MASK 0x1fff0000 /** Length of the colorburst */ # define TV_HBURST_LEN_SHIFT 0 # define TV_HBURST_LEN_MASK 0x0001fff /** @} */ /** @defgroup TV_H_CTL_3 * @{ */ #define TV_H_CTL_3 0x68038 /** End of hblank, measured in pixels minus one from start of hsync */ # define TV_HBLANK_END_SHIFT 16 # define TV_HBLANK_END_MASK 0x1fff0000 /** Start of hblank, measured in pixels minus one from start of hsync */ # define TV_HBLANK_START_SHIFT 0 # define TV_HBLANK_START_MASK 0x0001fff /** @} */ /** @defgroup TV_V_CTL_1 * @{ */ #define TV_V_CTL_1 0x6803c /** XXX */ # define TV_NBR_END_SHIFT 16 # define TV_NBR_END_MASK 0x07ff0000 /** XXX */ # define TV_VI_END_F1_SHIFT 8 # define TV_VI_END_F1_MASK 0x00003f00 /** XXX */ # define TV_VI_END_F2_SHIFT 0 # define TV_VI_END_F2_MASK 0x0000003f /** @} */ /** @defgroup TV_V_CTL_2 * @{ */ #define TV_V_CTL_2 0x68040 /** Length of vsync, in half lines */ # define TV_VSYNC_LEN_MASK 0x07ff0000 # define TV_VSYNC_LEN_SHIFT 16 /** Offset of the start of vsync in field 1, measured in one less than the * number of half lines. */ # define TV_VSYNC_START_F1_MASK 0x00007f00 # define TV_VSYNC_START_F1_SHIFT 8 /** * Offset of the start of vsync in field 2, measured in one less than the * number of half lines. */ # define TV_VSYNC_START_F2_MASK 0x0000007f # define TV_VSYNC_START_F2_SHIFT 0 /** @} */ /** @defgroup TV_V_CTL_3 * @{ */ #define TV_V_CTL_3 0x68044 /** Enables generation of the equalization signal */ # define TV_EQUAL_ENA (1 << 31) /** Length of vsync, in half lines */ # define TV_VEQ_LEN_MASK 0x007f0000 # define TV_VEQ_LEN_SHIFT 16 /** Offset of the start of equalization in field 1, measured in one less than * the number of half lines. */ # define TV_VEQ_START_F1_MASK 0x0007f00 # define TV_VEQ_START_F1_SHIFT 8 /** * Offset of the start of equalization in field 2, measured in one less than * the number of half lines. */ # define TV_VEQ_START_F2_MASK 0x000007f # define TV_VEQ_START_F2_SHIFT 0 /** @} */ /** @defgroup TV_V_CTL_4 * @{ */ #define TV_V_CTL_4 0x68048 /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F1_MASK 0x003f0000 # define TV_VBURST_START_F1_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F1_MASK 0x000000ff # define TV_VBURST_END_F1_SHIFT 0 /** @} */ /** @defgroup TV_V_CTL_5 * @{ */ #define TV_V_CTL_5 0x6804c /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F2_MASK 0x003f0000 # define TV_VBURST_START_F2_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F2_MASK 0x000000ff # define TV_VBURST_END_F2_SHIFT 0 /** @} */ /** @defgroup TV_V_CTL_6 * @{ */ #define TV_V_CTL_6 0x68050 /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F3_MASK 0x003f0000 # define TV_VBURST_START_F3_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F3_MASK 0x000000ff # define TV_VBURST_END_F3_SHIFT 0 /** @} */ /** @defgroup TV_V_CTL_7 * @{ */ #define TV_V_CTL_7 0x68054 /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F4_MASK 0x003f0000 # define TV_VBURST_START_F4_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F4_MASK 0x000000ff # define TV_VBURST_END_F4_SHIFT 0 /** @} */ /** @defgroup TV_SC_CTL_1 * @{ */ #define TV_SC_CTL_1 0x68060 /** Turns on the first subcarrier phase generation DDA */ # define TV_SC_DDA1_EN (1 << 31) /** Turns on the first subcarrier phase generation DDA */ # define TV_SC_DDA2_EN (1 << 30) /** Turns on the first subcarrier phase generation DDA */ # define TV_SC_DDA3_EN (1 << 29) /** Sets the subcarrier DDA to reset frequency every other field */ # define TV_SC_RESET_EVERY_2 (0 << 24) /** Sets the subcarrier DDA to reset frequency every fourth field */ # define TV_SC_RESET_EVERY_4 (1 << 24) /** Sets the subcarrier DDA to reset frequency every eighth field */ # define TV_SC_RESET_EVERY_8 (2 << 24) /** Sets the subcarrier DDA to never reset the frequency */ # define TV_SC_RESET_NEVER (3 << 24) /** Sets the peak amplitude of the colorburst.*/ # define TV_BURST_LEVEL_MASK 0x00ff0000 # define TV_BURST_LEVEL_SHIFT 16 /** Sets the increment of the first subcarrier phase generation DDA */ # define TV_SCDDA1_INC_MASK 0x00000fff # define TV_SCDDA1_INC_SHIFT 0 /** @} */ /** @defgroup TV_SC_CTL_2 * @{ */ #define TV_SC_CTL_2 0x68064 /** Sets the rollover for the second subcarrier phase generation DDA */ # define TV_SCDDA2_SIZE_MASK 0x7fff0000 # define TV_SCDDA2_SIZE_SHIFT 16 /** Sets the increent of the second subcarrier phase generation DDA */ # define TV_SCDDA2_INC_MASK 0x00007fff # define TV_SCDDA2_INC_SHIFT 0 /** @} */ /** @defgroup TV_SC_CTL_3 * @{ */ #define TV_SC_CTL_3 0x68068 /** Sets the rollover for the third subcarrier phase generation DDA */ # define TV_SCDDA3_SIZE_MASK 0x7fff0000 # define TV_SCDDA3_SIZE_SHIFT 16 /** Sets the increent of the third subcarrier phase generation DDA */ # define TV_SCDDA3_INC_MASK 0x00007fff # define TV_SCDDA3_INC_SHIFT 0 /** @} */ /** @defgroup TV_WIN_POS * @{ */ #define TV_WIN_POS 0x68070 /** X coordinate of the display from the start of horizontal active */ # define TV_XPOS_MASK 0x1fff0000 # define TV_XPOS_SHIFT 16 /** Y coordinate of the display from the start of vertical active (NBR) */ # define TV_YPOS_MASK 0x00000fff # define TV_YPOS_SHIFT 0 /** @} */ /** @defgroup TV_WIN_SIZE * @{ */ #define TV_WIN_SIZE 0x68074 /** Horizontal size of the display window, measured in pixels*/ # define TV_XSIZE_MASK 0x1fff0000 # define TV_XSIZE_SHIFT 16 /** * Vertical size of the display window, measured in pixels. * * Must be even for interlaced modes. */ # define TV_YSIZE_MASK 0x00000fff # define TV_YSIZE_SHIFT 0 /** @} */ /** @defgroup TV_FILTER_CTL_1 * @{ */ #define TV_FILTER_CTL_1 0x68080 /** * Enables automatic scaling calculation. * * If set, the rest of the registers are ignored, and the calculated values can * be read back from the register. */ # define TV_AUTO_SCALE (1 << 31) /** * Disables the vertical filter. * * This is required on modes more than 1024 pixels wide */ # define TV_V_FILTER_BYPASS (1 << 29) /** Enables adaptive vertical filtering */ # define TV_VADAPT (1 << 28) # define TV_VADAPT_MODE_MASK (3 << 26) /** Selects the least adaptive vertical filtering mode */ # define TV_VADAPT_MODE_LEAST (0 << 26) /** Selects the moderately adaptive vertical filtering mode */ # define TV_VADAPT_MODE_MODERATE (1 << 26) /** Selects the most adaptive vertical filtering mode */ # define TV_VADAPT_MODE_MOST (3 << 26) /** * Sets the horizontal scaling factor. * * This should be the fractional part of the horizontal scaling factor divided * by the oversampling rate. TV_HSCALE should be less than 1, and set to: * * (src width - 1) / ((oversample * dest width) - 1) */ # define TV_HSCALE_FRAC_MASK 0x00003fff # define TV_HSCALE_FRAC_SHIFT 0 /** @} */ /** @defgroup TV_FILTER_CTL_2 * @{ */ #define TV_FILTER_CTL_2 0x68084 /** * Sets the integer part of the 3.15 fixed-point vertical scaling factor. * * TV_VSCALE should be (src height - 1) / ((interlace * dest height) - 1) */ # define TV_VSCALE_INT_MASK 0x00038000 # define TV_VSCALE_INT_SHIFT 15 /** * Sets the fractional part of the 3.15 fixed-point vertical scaling factor. * * \sa TV_VSCALE_INT_MASK */ # define TV_VSCALE_FRAC_MASK 0x00007fff # define TV_VSCALE_FRAC_SHIFT 0 /** @} */ /** @defgroup TV_FILTER_CTL_3 * @{ */ #define TV_FILTER_CTL_3 0x68088 /** * Sets the integer part of the 3.15 fixed-point vertical scaling factor. * * TV_VSCALE should be (src height - 1) / (1/4 * (dest height - 1)) * * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes. */ # define TV_VSCALE_IP_INT_MASK 0x00038000 # define TV_VSCALE_IP_INT_SHIFT 15 /** * Sets the fractional part of the 3.15 fixed-point vertical scaling factor. * * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes. * * \sa TV_VSCALE_IP_INT_MASK */ # define TV_VSCALE_IP_FRAC_MASK 0x00007fff # define TV_VSCALE_IP_FRAC_SHIFT 0 /** @} */ /** @defgroup TV_CC_CONTROL * @{ */ #define TV_CC_CONTROL 0x68090 # define TV_CC_ENABLE (1 << 31) /** * Specifies which field to send the CC data in. * * CC data is usually sent in field 0. */ # define TV_CC_FID_MASK (1 << 27) # define TV_CC_FID_SHIFT 27 /** Sets the horizontal position of the CC data. Usually 135. */ # define TV_CC_HOFF_MASK 0x03ff0000 # define TV_CC_HOFF_SHIFT 16 /** Sets the vertical position of the CC data. Usually 21 */ # define TV_CC_LINE_MASK 0x0000003f # define TV_CC_LINE_SHIFT 0 /** @} */ /** @defgroup TV_CC_DATA * @{ */ #define TV_CC_DATA 0x68094 # define TV_CC_RDY (1 << 31) /** Second word of CC data to be transmitted. */ # define TV_CC_DATA_2_MASK 0x007f0000 # define TV_CC_DATA_2_SHIFT 16 /** First word of CC data to be transmitted. */ # define TV_CC_DATA_1_MASK 0x0000007f # define TV_CC_DATA_1_SHIFT 0 /** @} */ /** @{ */ #define TV_H_LUMA_0 0x68100 #define TV_H_LUMA_59 0x681ec #define TV_H_CHROMA_0 0x68200 #define TV_H_CHROMA_59 0x682ec #define TV_V_LUMA_0 0x68300 #define TV_V_LUMA_42 0x683a8 #define TV_V_CHROMA_0 0x68400 #define TV_V_CHROMA_42 0x684a8 /** @} */ #define PIPEA_DSL 0x70000 #define PIPEACONF 0x70008 #define PIPEACONF_ENABLE (1<<31) #define PIPEACONF_DISABLE 0 #define PIPEACONF_DOUBLE_WIDE (1<<30) #define I965_PIPECONF_ACTIVE (1<<30) #define PIPEACONF_SINGLE_WIDE 0 #define PIPEACONF_PIPE_UNLOCKED 0 #define PIPEACONF_PIPE_LOCKED (1<<25) #define PIPEACONF_PALETTE 0 #define PIPEACONF_GAMMA (1<<24) #define PIPECONF_FORCE_BORDER (1<<25) #define PIPECONF_PROGRESSIVE (0 << 21) #define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21) #define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21) #define PIPEAGCMAXRED 0x70010 #define PIPEAGCMAXGREEN 0x70014 #define PIPEAGCMAXBLUE 0x70018 #define PIPEASTAT 0x70024 # define FIFO_UNDERRUN (1 << 31) # define CRC_ERROR_ENABLE (1 << 29) # define CRC_DONE_ENABLE (1 << 28) # define GMBUS_EVENT_ENABLE (1 << 27) # define VSYNC_INT_ENABLE (1 << 25) # define DLINE_COMPARE_ENABLE (1 << 24) # define DPST_EVENT_ENABLE (1 << 23) # define LBLC_EVENT_ENABLE (1 << 22) # define OFIELD_INT_ENABLE (1 << 21) # define EFIELD_INT_ENABLE (1 << 20) # define SVBLANK_INT_ENABLE (1 << 18) # define VBLANK_INT_ENABLE (1 << 17) # define OREG_UPDATE_ENABLE (1 << 16) # define CRC_ERROR_INT_STATUS (1 << 13) # define CRC_DONE_INT_STATUS (1 << 12) # define GMBUS_INT_STATUS (1 << 11) # define VSYNC_INT_STATUS (1 << 9) # define DLINE_COMPARE_STATUS (1 << 8) # define DPST_EVENT_STATUS (1 << 7) # define LBLC_EVENT_STATUS (1 << 6) # define OFIELD_INT_STATUS (1 << 5) # define EFIELD_INT_STATUS (1 << 4) # define SVBLANK_INT_STATUS (1 << 2) # define VBLANK_INT_STATUS (1 << 1) # define OREG_UPDATE_STATUS (1 << 0) #define DSPARB 0x70030 #define DSPFW1 0x70034 #define DSPFW2 0x70038 #define DSPFW3 0x7003c /* * The two pipe frame counter registers are not synchronized, so * reading a stable value is somewhat tricky. The following code * should work: * * do { * high1 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >> PIPE_FRAME_HIGH_SHIFT; * low1 = ((INREG(PIPEAFRAMEPIXEL) & PIPE_FRAME_LOW_MASK) >> PIPE_FRAME_LOW_SHIFT); * high2 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >> PIPE_FRAME_HIGH_SHIFT); * } while (high1 != high2); * frame = (high1 << 8) | low1; */ #define PIPEAFRAMEHIGH 0x70040 #define PIPE_FRAME_HIGH_MASK 0x0000ffff #define PIPE_FRAME_HIGH_SHIFT 0 #define PIPEAFRAMEPIXEL 0x70044 #define PIPE_FRAME_LOW_MASK 0xff000000 #define PIPE_FRAME_LOW_SHIFT 24 /* * Pixel within the current frame is counted in the PIPEAFRAMEPIXEL register * and is 24 bits wide. */ #define PIPE_PIXEL_MASK 0x00ffffff #define PIPE_PIXEL_SHIFT 0 #define PIPEB_DSL 0x71000 #define PIPEBCONF 0x71008 #define PIPEBCONF_ENABLE (1<<31) #define PIPEBCONF_DISABLE 0 #define PIPEBCONF_DOUBLE_WIDE (1<<30) #define PIPEBCONF_DISABLE 0 #define PIPEBCONF_GAMMA (1<<24) #define PIPEBCONF_PALETTE 0 #define PIPEBGCMAXRED 0x71010 #define PIPEBGCMAXGREEN 0x71014 #define PIPEBGCMAXBLUE 0x71018 #define PIPEBSTAT 0x71024 #define PIPEBFRAMEHIGH 0x71040 #define PIPEBFRAMEPIXEL 0x71044 #define DSPACNTR 0x70180 #define DSPBCNTR 0x71180 #define DISPLAY_PLANE_ENABLE (1<<31) #define DISPLAY_PLANE_DISABLE 0 #define DISPLAY_PLANE_TILED (1<<10) #define DISPPLANE_GAMMA_ENABLE (1<<30) #define DISPPLANE_GAMMA_DISABLE 0 #define DISPPLANE_PIXFORMAT_MASK (0xf<<26) #define DISPPLANE_8BPP (0x2<<26) #define DISPPLANE_15_16BPP (0x4<<26) #define DISPPLANE_16BPP (0x5<<26) #define DISPPLANE_32BPP_NO_ALPHA (0x6<<26) #define DISPPLANE_32BPP (0x7<<26) #define DISPPLANE_STEREO_ENABLE (1<<25) #define DISPPLANE_STEREO_DISABLE 0 #define DISPPLANE_SEL_PIPE_MASK (1<<24) #define DISPPLANE_SEL_PIPE_A 0 #define DISPPLANE_SEL_PIPE_B (1<<24) #define DISPPLANE_SRC_KEY_ENABLE (1<<22) #define DISPPLANE_SRC_KEY_DISABLE 0 #define DISPPLANE_LINE_DOUBLE (1<<20) #define DISPPLANE_NO_LINE_DOUBLE 0 #define DISPPLANE_STEREO_POLARITY_FIRST 0 #define DISPPLANE_STEREO_POLARITY_SECOND (1<<18) /* plane B only */ #define DISPPLANE_ALPHA_TRANS_ENABLE (1<<15) #define DISPPLANE_ALPHA_TRANS_DISABLE 0 #define DISPPLANE_SPRITE_ABOVE_DISPLAYA 0 #define DISPPLANE_SPRITE_ABOVE_OVERLAY (1) #define DSPABASE 0x70184 #define DSPASTRIDE 0x70188 #define DSPBBASE 0x71184 #define DSPBADDR DSPBBASE #define DSPBSTRIDE 0x71188 #define DSPAKEYVAL 0x70194 #define DSPAKEYMASK 0x70198 #define DSPAPOS 0x7018C /* reserved */ #define DSPASIZE 0x70190 #define DSPBPOS 0x7118C #define DSPBSIZE 0x71190 #define DSPASURF 0x7019C #define DSPATILEOFF 0x701A4 #define DSPBSURF 0x7119C #define DSPBTILEOFF 0x711A4 #define VGACNTRL 0x71400 # define VGA_DISP_DISABLE (1 << 31) # define VGA_2X_MODE (1 << 30) # define VGA_PIPE_B_SELECT (1 << 29) /* Various masks for reserved bits, etc. */ #define I830_FWATER1_MASK (~((1<<11)|(1<<10)|(1<<9)| \ (1<<8)|(1<<26)|(1<<25)|(1<<24)|(1<<5)|(1<<4)|(1<<3)| \ (1<<2)|(1<<1)|1|(1<<20)|(1<<19)|(1<<18)|(1<<17)|(1<<16))) #define I830_FWATER2_MASK ~(0) #define DV0A_RESERVED ((1<<26)|(1<<25)|(1<<24)|(1<<23)|(1<<22)|(1<<21)|(1<<20)|(1<<19)|(1<<18)|(1<<16)|(1<<5)|(1<<1)|1) #define DV0B_RESERVED ((1<<27)|(1<<26)|(1<<25)|(1<<24)|(1<<23)|(1<<22)|(1<<21)|(1<<20)|(1<<19)|(1<<18)|(1<<16)|(1<<5)|(1<<1)|1) #define VGA0_N_DIVISOR_MASK ((1<<21)|(1<<20)|(1<<19)|(1<<18)|(1<<17)|(1<<16)) #define VGA0_M1_DIVISOR_MASK ((1<<13)|(1<<12)|(1<<11)|(1<<10)|(1<<9)|(1<<8)) #define VGA0_M2_DIVISOR_MASK ((1<<5)|(1<<4)|(1<<3)|(1<<2)|(1<<1)|1) #define VGA0_M1M2N_RESERVED ~(VGA0_N_DIVISOR_MASK|VGA0_M1_DIVISOR_MASK|VGA0_M2_DIVISOR_MASK) #define VGA0_POSTDIV_MASK ((1<<7)|(1<<5)|(1<<4)|(1<<3)|(1<<2)|(1<<1)|1) #define VGA1_POSTDIV_MASK ((1<<15)|(1<<13)|(1<<12)|(1<<11)|(1<<10)|(1<<9)|(1<<8)) #define VGA_POSTDIV_RESERVED ~(VGA0_POSTDIV_MASK|VGA1_POSTDIV_MASK|(1<<7)|(1<<15)) #define DPLLA_POSTDIV_MASK ((1<<23)|(1<<21)|(1<<20)|(1<<19)|(1<<18)|(1<<17)|(1<<16)) #define DPLLA_RESERVED ((1<<27)|(1<<26)|(1<<25)|(1<<24)|(1<<22)|(1<<15)|(1<<12)|(1<<11)|(1<<10)|(1<<9)|(1<<8)|(1<<7)|(1<<6)|(1<<5)|(1<<4)|(1<<3)|(1<<2)|(1<<1)|1) #define ADPA_RESERVED ((1<<2)|(1<<1)|1|(1<<9)|(1<<8)|(1<<7)|(1<<6)|(1<<5)|(1<<30)|(1<<29)|(1<<28)|(1<<27)|(1<<26)|(1<<25)|(1<<24)|(1<<23)|(1<<22)|(1<<21)|(1<<20)|(1<<19)|(1<<18)|(1<<17)|(1<<16)) #define SUPER_WORD 32 #define BURST_A_MASK ((1<<11)|(1<<10)|(1<<9)|(1<<8)) #define BURST_B_MASK ((1<<26)|(1<<25)|(1<<24)) #define WATER_A_MASK ((1<<5)|(1<<4)|(1<<3)|(1<<2)|(1<<1)|1) #define WATER_B_MASK ((1<<20)|(1<<19)|(1<<18)|(1<<17)|(1<<16)) #define WATER_RESERVED ((1<<31)|(1<<30)|(1<<29)|(1<<28)|(1<<27)|(1<<23)|(1<<22)|(1<<21)|(1<<15)|(1<<14)|(1<<13)|(1<<12)|(1<<7)|(1<<6)) #define PIPEACONF_RESERVED ((1<<29)|(1<<28)|(1<<27)|(1<<23)|(1<<22)|(1<<21)|(1<<20)|(1<<19)|(1<<18)|(1<<17)|(1<<16)|0xffff) #define PIPEBCONF_RESERVED ((1<<30)|(1<<29)|(1<<28)|(1<<27)|(1<<26)|(1<<25)|(1<<23)|(1<<22)|(1<<21)|(1<<20)|(1<<19)|(1<<18)|(1<<17)|(1<<16)|0xffff) #define DSPACNTR_RESERVED ((1<<23)|(1<<19)|(1<<17)|(1<<16)|0xffff) #define DSPBCNTR_RESERVED ((1<<23)|(1<<19)|(1<<17)|(1<<16)|0x7ffe) #define I830_GMCH_CTRL 0x52 #define I830_GMCH_ENABLED 0x4 #define I830_GMCH_MEM_MASK 0x1 #define I830_GMCH_MEM_64M 0x1 #define I830_GMCH_MEM_128M 0 #define I830_GMCH_GMS_MASK 0x70 #define I830_GMCH_GMS_DISABLED 0x00 #define I830_GMCH_GMS_LOCAL 0x10 #define I830_GMCH_GMS_STOLEN_512 0x20 #define I830_GMCH_GMS_STOLEN_1024 0x30 #define I830_GMCH_GMS_STOLEN_8192 0x40 #define I830_RDRAM_CHANNEL_TYPE 0x03010 #define I830_RDRAM_ND(x) (((x) & 0x20) >> 5) #define I830_RDRAM_DDT(x) (((x) & 0x18) >> 3) #define I855_GMCH_GMS_MASK (0xF << 4) #define I855_GMCH_GMS_DISABLED 0x00 #define I855_GMCH_GMS_STOLEN_1M (0x1 << 4) #define I855_GMCH_GMS_STOLEN_4M (0x2 << 4) #define I855_GMCH_GMS_STOLEN_8M (0x3 << 4) #define I855_GMCH_GMS_STOLEN_16M (0x4 << 4) #define I855_GMCH_GMS_STOLEN_32M (0x5 << 4) #define I915G_GMCH_GMS_STOLEN_48M (0x6 << 4) #define I915G_GMCH_GMS_STOLEN_64M (0x7 << 4) #define G33_GMCH_GMS_STOLEN_128M (0x8 << 4) #define G33_GMCH_GMS_STOLEN_256M (0x9 << 4) #define I85X_CAPID 0x44 #define I85X_VARIANT_MASK 0x7 #define I85X_VARIANT_SHIFT 5 #define I855_GME 0x0 #define I855_GM 0x4 #define I852_GME 0x2 #define I852_GM 0x5 #define I915_GCFGC 0xf0 #define I915_LOW_FREQUENCY_ENABLE (1 << 7) #define I915_DISPLAY_CLOCK_190_200_MHZ (0 << 4) #define I915_DISPLAY_CLOCK_333_MHZ (4 << 4) #define I915_DISPLAY_CLOCK_MASK (7 << 4) #define I855_HPLLCC 0xc0 #define I855_CLOCK_CONTROL_MASK (3 << 0) #define I855_CLOCK_133_200 (0 << 0) #define I855_CLOCK_100_200 (1 << 0) #define I855_CLOCK_100_133 (2 << 0) #define I855_CLOCK_166_250 (3 << 0) /* BLT commands */ #define COLOR_BLT_CMD ((2<<29)|(0x40<<22)|(0x3)) #define COLOR_BLT_WRITE_ALPHA (1<<21) #define COLOR_BLT_WRITE_RGB (1<<20) #define XY_COLOR_BLT_CMD ((2<<29)|(0x50<<22)|(0x4)) #define XY_COLOR_BLT_WRITE_ALPHA (1<<21) #define XY_COLOR_BLT_WRITE_RGB (1<<20) #define XY_COLOR_BLT_TILED (1<<11) #define XY_SETUP_CLIP_BLT_CMD ((2<<29)|(3<<22)|1) #define XY_SRC_COPY_BLT_CMD ((2<<29)|(0x53<<22)|6) #define XY_SRC_COPY_BLT_WRITE_ALPHA (1<<21) #define XY_SRC_COPY_BLT_WRITE_RGB (1<<20) #define XY_SRC_COPY_BLT_SRC_TILED (1<<15) #define XY_SRC_COPY_BLT_DST_TILED (1<<11) #define SRC_COPY_BLT_CMD ((2<<29)|(0x43<<22)|0x4) #define SRC_COPY_BLT_WRITE_ALPHA (1<<21) #define SRC_COPY_BLT_WRITE_RGB (1<<20) #define XY_PAT_BLT_IMMEDIATE ((2<<29)|(0x72<<22)) #define XY_MONO_PAT_BLT_CMD ((0x2<<29)|(0x52<<22)|0x7) #define XY_MONO_PAT_VERT_SEED ((1<<10)|(1<<9)|(1<<8)) #define XY_MONO_PAT_HORT_SEED ((1<<14)|(1<<13)|(1<<12)) #define XY_MONO_PAT_BLT_WRITE_ALPHA (1<<21) #define XY_MONO_PAT_BLT_WRITE_RGB (1<<20) #define XY_MONO_SRC_BLT_CMD ((0x2<<29)|(0x54<<22)|(0x6)) #define XY_MONO_SRC_BLT_WRITE_ALPHA (1<<21) #define XY_MONO_SRC_BLT_WRITE_RGB (1<<20) #define STATE3D_FOG_MODE ((3<<29)|(0x1d<<24)|(0x89<<16)|2) #define FOG_MODE_VERTEX (1<<31) #define DISABLE_TEX_TRANSFORM (1<<28) #define TEXTURE_SET(x) (x<<29) #define STATE3D_VERTEX_TRANSFORM ((3<<29)|(0x1d<<24)|(0x8b<<16)) #define DISABLE_VIEWPORT_TRANSFORM (1<<31) #define DISABLE_PERSPECTIVE_DIVIDE (1<<29) #define MI_SET_CONTEXT (0x18<<23) #define CTXT_NO_RESTORE (1) #define CTXT_PALETTE_SAVE_DISABLE (1<<3) #define CTXT_PALETTE_RESTORE_DISABLE (1<<2) /* Dword 0 */ #define MI_VERTEX_BUFFER (0x17<<23) #define MI_VERTEX_BUFFER_IDX(x) (x<<20) #define MI_VERTEX_BUFFER_PITCH(x) (x<<13) #define MI_VERTEX_BUFFER_WIDTH(x) (x<<6) /* Dword 1 */ #define MI_VERTEX_BUFFER_DISABLE (1) /* Overlay Flip */ #define MI_OVERLAY_FLIP (0x11<<23) #define MI_OVERLAY_FLIP_CONTINUE (0<<21) #define MI_OVERLAY_FLIP_ON (1<<21) #define MI_OVERLAY_FLIP_OFF (2<<21) /* Wait for Events */ #define MI_WAIT_FOR_EVENT (0x03<<23) #define MI_WAIT_FOR_OVERLAY_FLIP (1<<16) /* Flush */ #define MI_FLUSH (0x04<<23) #define MI_WRITE_DIRTY_STATE (1<<4) #define MI_END_SCENE (1<<3) #define MI_INHIBIT_RENDER_CACHE_FLUSH (1<<2) #define MI_STATE_INSTRUCTION_CACHE_FLUSH (1<<1) #define MI_INVALIDATE_MAP_CACHE (1<<0) /* broadwater flush bits */ #define BRW_MI_GLOBAL_SNAPSHOT_RESET (1 << 3) /* Noop */ #define MI_NOOP 0x00 #define MI_NOOP_WRITE_ID (1<<22) #define MI_NOOP_ID_MASK (1<<22 - 1) #define STATE3D_COLOR_FACTOR ((0x3<<29)|(0x1d<<24)|(0x01<<16)) /* STATE3D_FOG_MODE stuff */ #define ENABLE_FOG_SOURCE (1<<27) #define ENABLE_FOG_CONST (1<<24) #define ENABLE_FOG_DENSITY (1<<23) /* * New regs for broadwater -- we need to split this file up sensibly somehow. */ #define BRW_3D(Pipeline,Opcode,Subopcode) ((3 << 29) | \ ((Pipeline) << 27) | \ ((Opcode) << 24) | \ ((Subopcode) << 16)) #define BRW_URB_FENCE BRW_3D(0, 0, 0) #define BRW_CS_URB_STATE BRW_3D(0, 0, 1) #define BRW_CONSTANT_BUFFER BRW_3D(0, 0, 2) #define BRW_STATE_PREFETCH BRW_3D(0, 0, 3) #define BRW_STATE_BASE_ADDRESS BRW_3D(0, 1, 1) #define BRW_STATE_SIP BRW_3D(0, 1, 2) #define BRW_PIPELINE_SELECT BRW_3D(0, 1, 4) #define NEW_PIPELINE_SELECT BRW_3D(1, 1, 4) #define BRW_MEDIA_STATE_POINTERS BRW_3D(2, 0, 0) #define BRW_MEDIA_OBJECT BRW_3D(2, 1, 0) #define BRW_3DSTATE_PIPELINED_POINTERS BRW_3D(3, 0, 0) #define BRW_3DSTATE_BINDING_TABLE_POINTERS BRW_3D(3, 0, 1) #define BRW_3DSTATE_VERTEX_BUFFERS BRW_3D(3, 0, 8) #define BRW_3DSTATE_VERTEX_ELEMENTS BRW_3D(3, 0, 9) #define BRW_3DSTATE_INDEX_BUFFER BRW_3D(3, 0, 0xa) #define BRW_3DSTATE_VF_STATISTICS BRW_3D(3, 0, 0xb) #define BRW_3DSTATE_DRAWING_RECTANGLE BRW_3D(3, 1, 0) #define BRW_3DSTATE_CONSTANT_COLOR BRW_3D(3, 1, 1) #define BRW_3DSTATE_SAMPLER_PALETTE_LOAD BRW_3D(3, 1, 2) #define BRW_3DSTATE_CHROMA_KEY BRW_3D(3, 1, 4) #define BRW_3DSTATE_DEPTH_BUFFER BRW_3D(3, 1, 5) #define BRW_3DSTATE_POLY_STIPPLE_OFFSET BRW_3D(3, 1, 6) #define BRW_3DSTATE_POLY_STIPPLE_PATTERN BRW_3D(3, 1, 7) #define BRW_3DSTATE_LINE_STIPPLE BRW_3D(3, 1, 8) #define BRW_3DSTATE_GLOBAL_DEPTH_OFFSET_CLAMP BRW_3D(3, 1, 9) /* These two are BLC and CTG only, not BW or CL */ #define BRW_3DSTATE_AA_LINE_PARAMS BRW_3D(3, 1, 0xa) #define BRW_3DSTATE_GS_SVB_INDEX BRW_3D(3, 1, 0xb) #define BRW_PIPE_CONTROL BRW_3D(3, 2, 0) #define BRW_3DPRIMITIVE BRW_3D(3, 3, 0) #define PIPELINE_SELECT_3D 0 #define PIPELINE_SELECT_MEDIA 1 #define UF0_CS_REALLOC (1 << 13) #define UF0_VFE_REALLOC (1 << 12) #define UF0_SF_REALLOC (1 << 11) #define UF0_CLIP_REALLOC (1 << 10) #define UF0_GS_REALLOC (1 << 9) #define UF0_VS_REALLOC (1 << 8) #define UF1_CLIP_FENCE_SHIFT 20 #define UF1_GS_FENCE_SHIFT 10 #define UF1_VS_FENCE_SHIFT 0 #define UF2_CS_FENCE_SHIFT 20 #define UF2_VFE_FENCE_SHIFT 10 #define UF2_SF_FENCE_SHIFT 0 /* for BRW_STATE_BASE_ADDRESS */ #define BASE_ADDRESS_MODIFY (1 << 0) /* for BRW_3DSTATE_PIPELINED_POINTERS */ #define BRW_GS_DISABLE 0 #define BRW_GS_ENABLE 1 #define BRW_CLIP_DISABLE 0 #define BRW_CLIP_ENABLE 1 /* for BRW_PIPE_CONTROL */ #define BRW_PIPE_CONTROL_NOWRITE (0 << 14) #define BRW_PIPE_CONTROL_WRITE_QWORD (1 << 14) #define BRW_PIPE_CONTROL_WRITE_DEPTH (2 << 14) #define BRW_PIPE_CONTROL_WRITE_TIME (3 << 14) #define BRW_PIPE_CONTROL_DEPTH_STALL (1 << 13) #define BRW_PIPE_CONTROL_WC_FLUSH (1 << 12) #define BRW_PIPE_CONTROL_IS_FLUSH (1 << 11) #define BRW_PIPE_CONTROL_NOTIFY_ENABLE (1 << 8) #define BRW_PIPE_CONTROL_GLOBAL_GTT (1 << 2) #define BRW_PIPE_CONTROL_LOCAL_PGTT (0 << 2) /* VERTEX_BUFFER_STATE Structure */ #define VB0_BUFFER_INDEX_SHIFT 27 #define VB0_VERTEXDATA (0 << 26) #define VB0_INSTANCEDATA (1 << 26) #define VB0_BUFFER_PITCH_SHIFT 0 /* VERTEX_ELEMENT_STATE Structure */ #define VE0_VERTEX_BUFFER_INDEX_SHIFT 27 #define VE0_VALID (1 << 26) #define VE0_FORMAT_SHIFT 16 #define VE0_OFFSET_SHIFT 0 #define VE1_VFCOMPONENT_0_SHIFT 28 #define VE1_VFCOMPONENT_1_SHIFT 24 #define VE1_VFCOMPONENT_2_SHIFT 20 #define VE1_VFCOMPONENT_3_SHIFT 16 #define VE1_DESTINATION_ELEMENT_OFFSET_SHIFT 0 /* 3DPRIMITIVE bits */ #define BRW_3DPRIMITIVE_VERTEX_SEQUENTIAL (0 << 15) #define BRW_3DPRIMITIVE_VERTEX_RANDOM (1 << 15) /* Primitive types are in brw_defines.h */ #define BRW_3DPRIMITIVE_TOPOLOGY_SHIFT 10 #define BRW_SVG_CTL 0x7400 #define BRW_SVG_CTL_GS_BA (0 << 8) #define BRW_SVG_CTL_SS_BA (1 << 8) #define BRW_SVG_CTL_IO_BA (2 << 8) #define BRW_SVG_CTL_GS_AUB (3 << 8) #define BRW_SVG_CTL_IO_AUB (4 << 8) #define BRW_SVG_CTL_SIP (5 << 8) #define BRW_SVG_RDATA 0x7404 #define BRW_SVG_WORK_CTL 0x7408 #define BRW_VF_CTL 0x7500 #define BRW_VF_CTL_SNAPSHOT_COMPLETE (1 << 31) #define BRW_VF_CTL_SNAPSHOT_MUX_SELECT_THREADID (0 << 8) #define BRW_VF_CTL_SNAPSHOT_MUX_SELECT_VF_DEBUG (1 << 8) #define BRW_VF_CTL_SNAPSHOT_TYPE_VERTEX_SEQUENCE (0 << 4) #define BRW_VF_CTL_SNAPSHOT_TYPE_VERTEX_INDEX (1 << 4) #define BRW_VF_CTL_SKIP_INITIAL_PRIMITIVES (1 << 3) #define BRW_VF_CTL_MAX_PRIMITIVES_LIMIT_ENABLE (1 << 2) #define BRW_VF_CTL_VERTEX_RANGE_LIMIT_ENABLE (1 << 1) #define BRW_VF_CTL_SNAPSHOT_ENABLE (1 << 0) #define BRW_VF_STRG_VAL 0x7504 #define BRW_VF_STR_VL_OVR 0x7508 #define BRW_VF_VC_OVR 0x750c #define BRW_VF_STR_PSKIP 0x7510 #define BRW_VF_MAX_PRIM 0x7514 #define BRW_VF_RDATA 0x7518 #define BRW_VS_CTL 0x7600 #define BRW_VS_CTL_SNAPSHOT_COMPLETE (1 << 31) #define BRW_VS_CTL_SNAPSHOT_MUX_VERTEX_0 (0 << 8) #define BRW_VS_CTL_SNAPSHOT_MUX_VERTEX_1 (1 << 8) #define BRW_VS_CTL_SNAPSHOT_MUX_VALID_COUNT (2 << 8) #define BRW_VS_CTL_SNAPSHOT_MUX_VS_KERNEL_POINTER (3 << 8) #define BRW_VS_CTL_SNAPSHOT_ALL_THREADS (1 << 2) #define BRW_VS_CTL_THREAD_SNAPSHOT_ENABLE (1 << 1) #define BRW_VS_CTL_SNAPSHOT_ENABLE (1 << 0) #define BRW_VS_STRG_VAL 0x7604 #define BRW_VS_RDATA 0x7608 #define BRW_SF_CTL 0x7b00 #define BRW_SF_CTL_SNAPSHOT_COMPLETE (1 << 31) #define BRW_SF_CTL_SNAPSHOT_MUX_VERTEX_0_FF_ID (0 << 8) #define BRW_SF_CTL_SNAPSHOT_MUX_VERTEX_0_REL_COUNT (1 << 8) #define BRW_SF_CTL_SNAPSHOT_MUX_VERTEX_1_FF_ID (2 << 8) #define BRW_SF_CTL_SNAPSHOT_MUX_VERTEX_1_REL_COUNT (3 << 8) #define BRW_SF_CTL_SNAPSHOT_MUX_VERTEX_2_FF_ID (4 << 8) #define BRW_SF_CTL_SNAPSHOT_MUX_VERTEX_2_REL_COUNT (5 << 8) #define BRW_SF_CTL_SNAPSHOT_MUX_VERTEX_COUNT (6 << 8) #define BRW_SF_CTL_SNAPSHOT_MUX_SF_KERNEL_POINTER (7 << 8) #define BRW_SF_CTL_MIN_MAX_PRIMITIVE_RANGE_ENABLE (1 << 4) #define BRW_SF_CTL_DEBUG_CLIP_RECTANGLE_ENABLE (1 << 3) #define BRW_SF_CTL_SNAPSHOT_ALL_THREADS (1 << 2) #define BRW_SF_CTL_THREAD_SNAPSHOT_ENABLE (1 << 1) #define BRW_SF_CTL_SNAPSHOT_ENABLE (1 << 0) #define BRW_SF_STRG_VAL 0x7b04 #define BRW_SF_RDATA 0x7b18 #define BRW_WIZ_CTL 0x7c00 #define BRW_WIZ_CTL_SNAPSHOT_COMPLETE (1 << 31) #define BRW_WIZ_CTL_SUBSPAN_INSTANCE_SHIFT 16 #define BRW_WIZ_CTL_SNAPSHOT_MUX_WIZ_KERNEL_POINTER (0 << 8) #define BRW_WIZ_CTL_SNAPSHOT_MUX_SUBSPAN_INSTANCE (1 << 8) #define BRW_WIZ_CTL_SNAPSHOT_MUX_PRIMITIVE_SEQUENCE (2 << 8) #define BRW_WIZ_CTL_SINGLE_SUBSPAN_DISPATCH (1 << 6) #define BRW_WIZ_CTL_IGNORE_COLOR_SCOREBOARD_STALLS (1 << 5) #define BRW_WIZ_CTL_ENABLE_SUBSPAN_INSTANCE_COMPARE (1 << 4) #define BRW_WIZ_CTL_USE_UPSTREAM_SNAPSHOT_FLAG (1 << 3) #define BRW_WIZ_CTL_SNAPSHOT_ALL_THREADS (1 << 2) #define BRW_WIZ_CTL_THREAD_SNAPSHOT_ENABLE (1 << 1) #define BRW_WIZ_CTL_SNAPSHOT_ENABLE (1 << 0) #define BRW_WIZ_STRG_VAL 0x7c04 #define BRW_WIZ_RDATA 0x7c18 #define BRW_TS_CTL 0x7e00 #define BRW_TS_CTL_SNAPSHOT_COMPLETE (1 << 31) #define BRW_TS_CTL_SNAPSHOT_MESSAGE_ERROR (0 << 8) #define BRW_TS_CTL_SNAPSHOT_INTERFACE_DESCRIPTOR (3 << 8) #define BRW_TS_CTL_SNAPSHOT_ALL_CHILD_THREADS (1 << 2) #define BRW_TS_CTL_SNAPSHOT_ALL_ROOT_THREADS (1 << 1) #define BRW_TS_CTL_SNAPSHOT_ENABLE (1 << 0) #define BRW_TS_STRG_VAL 0x7e04 #define BRW_TS_RDATA 0x7e08 #define BRW_TD_CTL 0x8000 #define BRW_TD_CTL_MUX_SHIFT 8 #define BRW_TD_CTL_EXTERNAL_HALT_R0_DEBUG_MATCH (1 << 7) #define BRW_TD_CTL_FORCE_EXTERNAL_HALT (1 << 6) #define BRW_TD_CTL_EXCEPTION_MASK_OVERRIDE (1 << 5) #define BRW_TD_CTL_FORCE_THREAD_BREAKPOINT_ENABLE (1 << 4) #define BRW_TD_CTL_BREAKPOINT_ENABLE (1 << 2) #define BRW_TD_CTL2 0x8004 #define BRW_TD_CTL2_ILLEGAL_OPCODE_EXCEPTION_OVERRIDE (1 << 28) #define BRW_TD_CTL2_MASKSTACK_EXCEPTION_OVERRIDE (1 << 26) #define BRW_TD_CTL2_SOFTWARE_EXCEPTION_OVERRIDE (1 << 25) #define BRW_TD_CTL2_ACTIVE_THREAD_LIMIT_SHIFT 16 #define BRW_TD_CTL2_ACTIVE_THREAD_LIMIT_ENABLE (1 << 8) #define BRW_TD_CTL2_THREAD_SPAWNER_EXECUTION_MASK_ENABLE (1 << 7) #define BRW_TD_CTL2_WIZ_EXECUTION_MASK_ENABLE (1 << 6) #define BRW_TD_CTL2_SF_EXECUTION_MASK_ENABLE (1 << 5) #define BRW_TD_CTL2_CLIPPER_EXECUTION_MASK_ENABLE (1 << 4) #define BRW_TD_CTL2_GS_EXECUTION_MASK_ENABLE (1 << 3) #define BRW_TD_CTL2_VS_EXECUTION_MASK_ENABLE (1 << 0) #define BRW_TD_VF_VS_EMSK 0x8008 #define BRW_TD_GS_EMSK 0x800c #define BRW_TD_CLIP_EMSK 0x8010 #define BRW_TD_SF_EMSK 0x8014 #define BRW_TD_WIZ_EMSK 0x8018 #define BRW_TD_0_6_EHTRG_VAL 0x801c #define BRW_TD_0_7_EHTRG_VAL 0x8020 #define BRW_TD_0_6_EHTRG_MSK 0x8024 #define BRW_TD_0_7_EHTRG_MSK 0x8028 #define BRW_TD_RDATA 0x802c #define BRW_TD_TS_EMSK 0x8030 #define BRW_EU_CTL 0x8800 #define BRW_EU_CTL_SELECT_SHIFT 16 #define BRW_EU_CTL_DATA_MUX_SHIFT 8 #define BRW_EU_ATT_0 0x8810 #define BRW_EU_ATT_1 0x8814 #define BRW_EU_ATT_DATA_0 0x8820 #define BRW_EU_ATT_DATA_1 0x8824 #define BRW_EU_ATT_CLR_0 0x8830 #define BRW_EU_ATT_CLR_1 0x8834 #define BRW_EU_RDATA 0x8840 /* End regs for broadwater */ #define MAX_DISPLAY_PIPES 2 typedef enum { CrtIndex = 0, TvIndex, DfpIndex, LfpIndex, Crt2Index, Tv2Index, Dfp2Index, Lfp2Index, NumDisplayTypes } DisplayType; /* What's connected to the pipes (as reported by the BIOS) */ #define PIPE_ACTIVE_MASK 0xff #define PIPE_CRT_ACTIVE (1 << CrtIndex) #define PIPE_TV_ACTIVE (1 << TvIndex) #define PIPE_DFP_ACTIVE (1 << DfpIndex) #define PIPE_LCD_ACTIVE (1 << LfpIndex) #define PIPE_CRT2_ACTIVE (1 << Crt2Index) #define PIPE_TV2_ACTIVE (1 << Tv2Index) #define PIPE_DFP2_ACTIVE (1 << Dfp2Index) #define PIPE_LCD2_ACTIVE (1 << Lfp2Index) #define PIPE_SIZED_DISP_MASK (PIPE_DFP_ACTIVE | \ PIPE_LCD_ACTIVE | \ PIPE_DFP2_ACTIVE) #define PIPE_A_SHIFT 0 #define PIPE_B_SHIFT 8 #define PIPE_SHIFT(n) ((n) == 0 ? \ PIPE_A_SHIFT : PIPE_B_SHIFT) /* * Some BIOS scratch area registers. The 845 (and 830?) store the amount * of video memory available to the BIOS in SWF1. */ #define SWF0 0x71410 #define SWF1 0x71414 #define SWF2 0x71418 #define SWF3 0x7141c #define SWF4 0x71420 #define SWF5 0x71424 #define SWF6 0x71428 /* * 855 scratch registers. */ #define SWF00 0x70410 #define SWF01 0x70414 #define SWF02 0x70418 #define SWF03 0x7041c #define SWF04 0x70420 #define SWF05 0x70424 #define SWF06 0x70428 #define SWF10 SWF0 #define SWF11 SWF1 #define SWF12 SWF2 #define SWF13 SWF3 #define SWF14 SWF4 #define SWF15 SWF5 #define SWF16 SWF6 #define SWF30 0x72414 #define SWF31 0x72418 #define SWF32 0x7241c /* * Overlay registers. These are overlay registers accessed via MMIO. * Those loaded via the overlay register page are defined in i830_video.c. */ #define OVADD 0x30000 #define DOVSTA 0x30008 #define OC_BUF (0x3<<20) #define OGAMC5 0x30010 #define OGAMC4 0x30014 #define OGAMC3 0x30018 #define OGAMC2 0x3001c #define OGAMC1 0x30020 #define OGAMC0 0x30024 /* * Palette registers */ #define PALETTE_A 0x0a000 #define PALETTE_B 0x0a800 /* Framebuffer compression */ #define FBC_CFB_BASE 0x03200 /* 4k page aligned */ #define FBC_LL_BASE 0x03204 /* 4k page aligned */ #define FBC_CONTROL 0x03208 #define FBC_CTL_EN (1<<31) #define FBC_CTL_PERIODIC (1<<30) #define FBC_CTL_INTERVAL_SHIFT (16) #define FBC_CTL_UNCOMPRESSIBLE (1<<14) #define FBC_CTL_STRIDE_SHIFT (5) #define FBC_CTL_FENCENO (1<<0) #define FBC_COMMAND 0x0320c #define FBC_CMD_COMPRESS (1<<0) #define FBC_STATUS 0x03210 #define FBC_STAT_COMPRESSING (1<<31) #define FBC_STAT_COMPRESSED (1<<30) #define FBC_STAT_MODIFIED (1<<29) #define FBC_STAT_CURRENT_LINE (1<<0) #define FBC_CONTROL2 0x03214 #define FBC_CTL_FENCE_DBL (0<<4) #define FBC_CTL_IDLE_IMM (0<<2) #define FBC_CTL_IDLE_FULL (1<<2) #define FBC_CTL_IDLE_LINE (2<<2) #define FBC_CTL_IDLE_DEBUG (3<<2) #define FBC_CTL_CPU_FENCE (1<<1) #define FBC_CTL_PLANEA (0<<0) #define FBC_CTL_PLANEB (1<<0) #define FBC_FENCE_OFF 0x0321b #define FBC_MOD_NUM 0x03220 #define FBC_TAG_DEBUG 0x03300 #define FBC_LL_SIZE (1536) #define FBC_LL_PAD (32) /* Framebuffer compression version 2 */ #define DPFC_CB_BASE 0x3200 #define DPFC_CONTROL 0x3208 #define DPFC_CTL_EN (1<<31) #define DPFC_CTL_PLANEA (0<<30) #define DPFC_CTL_PLANEB (1<<30) #define DPFC_CTL_FENCE_EN (1<<29) #define DPFC_CTL_LIMIT_1X (0<<6) #define DPFC_CTL_LIMIT_2X (1<<6) #define DPFC_CTL_LIMIT_4X (2<<6) #define DPFC_RECOMP_CTL 0x320c #define DPFC_RECOMP_STALL_EN (1<<27) #define DPFC_RECOMP_STALL_WM_SHIFT (16) #define DPFC_RECOMP_STALL_WM_MASK (0x07ff0000) #define DPFC_RECOMP_TIMER_COUNT_SHIFT (0) #define DPFC_RECOMP_TIMER_COUNT_MASK (0x0000003f) #define DPFC_STATUS 0x3210 #define DPFC_INVAL_SEG_SHIFT (16) #define DPFC_INVAL_SEG_MASK (0x07ff0000) #define DPFC_COMP_SEG_SHIFT (0) #define DPFC_COMP_SEG_MASK (0x000003ff) #define DPFC_STATUS2 0x3214 #define DPFC_FENCE_YOFF 0x3218 #endif /* _I810_REG_H */