/************************************************************************** Copyright 2006 Dave Airlie Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation on the rights to use, copy, modify, merge, publish, distribute, sub license, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice (including the next paragraph) shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL THE COPYRIGHT HOLDERS AND/OR THEIR SUPPLIERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. **************************************************************************/ /** @file * SDVO support for i915 and newer chipsets. * * The SDVO outputs send digital display data out over the PCIE bus to display * cards implementing a defined interface. These cards may have DVI, TV, CRT, * or other outputs on them. * * The system has two SDVO channels, which may be used for SDVO chips on the * motherboard, or in the external cards. The two channels may also be used * in a ganged mode to provide higher bandwidth to a single output. Currently, * this code doesn't deal with either ganged mode or more than one SDVO output. */ #ifdef HAVE_CONFIG_H #include "config.h" #endif #include #include "xf86.h" #include "xf86_OSproc.h" #include "compiler.h" #include "i830.h" #include "i830_display.h" #include "i810_reg.h" #include "i830_sdvo_regs.h" /** SDVO driver private structure. */ struct i830_sdvo_priv { /** SDVO device on SDVO I2C bus. */ I2CDevRec d; /** Register for the SDVO device: SDVOB or SDVOC */ int output_device; /** Active outputs controlled by this SDVO output */ CARD16 active_outputs; /** * Capabilities of the SDVO device returned by i830_sdvo_get_capabilities() */ struct i830_sdvo_caps caps; /** Pixel clock limitations reported by the SDVO device, in kHz */ int pixel_clock_min, pixel_clock_max; /** State for save/restore */ /** @{ */ int save_sdvo_mult; CARD16 save_active_outputs; struct i830_sdvo_dtd save_input_dtd_1, save_input_dtd_2; struct i830_sdvo_dtd save_output_dtd[16]; CARD32 save_SDVOX; /** @} */ }; /** Read a single byte from the given address on the SDVO device. */ static Bool i830_sdvo_read_byte(xf86OutputPtr output, int addr, unsigned char *ch) { I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; if (!xf86I2CReadByte(&dev_priv->d, addr, ch)) { xf86DrvMsg(intel_output->pI2CBus->scrnIndex, X_ERROR, "Unable to read from %s slave 0x%02x.\n", intel_output->pI2CBus->BusName, dev_priv->d.SlaveAddr); return FALSE; } return TRUE; } /** Read a single byte from the given address on the SDVO device. */ static Bool i830_sdvo_read_byte_quiet(xf86OutputPtr output, int addr, unsigned char *ch) { I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; return xf86I2CReadByte(&dev_priv->d, addr, ch); } /** Write a single byte to the given address on the SDVO device. */ static Bool i830_sdvo_write_byte(xf86OutputPtr output, int addr, unsigned char ch) { I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; if (!xf86I2CWriteByte(&dev_priv->d, addr, ch)) { xf86DrvMsg(intel_output->pI2CBus->scrnIndex, X_ERROR, "Unable to write to %s Slave 0x%02x.\n", intel_output->pI2CBus->BusName, dev_priv->d.SlaveAddr); return FALSE; } return TRUE; } #define SDVO_CMD_NAME_ENTRY(cmd) {cmd, #cmd} /** Mapping of command numbers to names, for debug output */ const static struct _sdvo_cmd_name { CARD8 cmd; char *name; } sdvo_cmd_names[] = { SDVO_CMD_NAME_ENTRY(SDVO_CMD_RESET), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_DEVICE_CAPS), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_FIRMWARE_REV), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_TRAINED_INPUTS), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_ACTIVE_OUTPUTS), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_ACTIVE_OUTPUTS), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_IN_OUT_MAP), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_IN_OUT_MAP), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_ATTACHED_DISPLAYS), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_HOT_PLUG_SUPPORT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_ACTIVE_HOT_PLUG), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_ACTIVE_HOT_PLUG), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_INTERRUPT_EVENT_SOURCE), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_TARGET_INPUT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_TARGET_OUTPUT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_INPUT_TIMINGS_PART1), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_INPUT_TIMINGS_PART2), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_INPUT_TIMINGS_PART1), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_INPUT_TIMINGS_PART2), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_INPUT_TIMINGS_PART1), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_OUTPUT_TIMINGS_PART1), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_OUTPUT_TIMINGS_PART2), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_OUTPUT_TIMINGS_PART1), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_OUTPUT_TIMINGS_PART2), SDVO_CMD_NAME_ENTRY(SDVO_CMD_CREATE_PREFERRED_INPUT_TIMING), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART1), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART2), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_INPUT_PIXEL_CLOCK_RANGE), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_OUTPUT_PIXEL_CLOCK_RANGE), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_SUPPORTED_CLOCK_RATE_MULTS), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_CLOCK_RATE_MULT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_CLOCK_RATE_MULT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_SUPPORTED_TV_FORMATS), SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_TV_FORMAT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_TV_FORMAT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_TV_RESOLUTION_SUPPORT), SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_CONTROL_BUS_SWITCH), }; static I2CSlaveAddr slaveAddr; #define SDVO_NAME(dev_priv) ((dev_priv)->output_device == SDVOB ? "SDVO" : "SDVO") #define SDVO_PRIV(output) ((struct i830_sdvo_priv *) (output)->dev_priv) /** * Writes out the data given in args (up to 8 bytes), followed by the opcode. */ static void i830_sdvo_write_cmd(xf86OutputPtr output, CARD8 cmd, void *args, int args_len) { I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; int i; if (slaveAddr && slaveAddr != dev_priv->d.SlaveAddr) ErrorF ("Mismatch slave addr %x != %x\n", slaveAddr, dev_priv->d.SlaveAddr); /* Write the SDVO command logging */ xf86DrvMsg(intel_output->pI2CBus->scrnIndex, X_INFO, "%s: W: %02X ", SDVO_NAME(dev_priv), cmd); for (i = 0; i < args_len; i++) LogWrite(1, "%02X ", ((CARD8 *)args)[i]); for (; i < 8; i++) LogWrite(1, " "); for (i = 0; i < sizeof(sdvo_cmd_names) / sizeof(sdvo_cmd_names[0]); i++) { if (cmd == sdvo_cmd_names[i].cmd) { LogWrite(1, "(%s)", sdvo_cmd_names[i].name); break; } } if (i == sizeof(sdvo_cmd_names) / sizeof(sdvo_cmd_names[0])) LogWrite(1, "(%02X)", cmd); LogWrite(1, "\n"); /* send the output regs */ for (i = 0; i < args_len; i++) { i830_sdvo_write_byte(output, SDVO_I2C_ARG_0 - i, ((CARD8 *)args)[i]); } /* blast the command reg */ i830_sdvo_write_byte(output, SDVO_I2C_OPCODE, cmd); } static const char *cmd_status_names[] = { "Power on", "Success", "Not supported", "Invalid arg", "Pending", "Target not specified", "Scaling not supported" }; /** * Reads back response_len bytes from the SDVO device, and returns the status. */ static CARD8 i830_sdvo_read_response(xf86OutputPtr output, void *response, int response_len) { I830OutputPrivatePtr intel_output = output->driver_private; int i; CARD8 status; /* Read the command response */ for (i = 0; i < response_len; i++) { i830_sdvo_read_byte(output, SDVO_I2C_RETURN_0 + i, &((CARD8 *)response)[i]); } /* Read the return status */ i830_sdvo_read_byte(output, SDVO_I2C_CMD_STATUS, &status); /* Write the SDVO command logging */ xf86DrvMsg(intel_output->pI2CBus->scrnIndex, X_INFO, "%s: R: ", SDVO_NAME(SDVO_PRIV(intel_output))); for (i = 0; i < response_len; i++) LogWrite(1, "%02X ", ((CARD8 *)response)[i]); for (; i < 8; i++) LogWrite(1, " "); if (status <= SDVO_CMD_STATUS_SCALING_NOT_SUPP) { LogWrite(1, "(%s)", cmd_status_names[status]); } else { LogWrite(1, "(??? %d)", status); } LogWrite(1, "\n"); return status; } int i830_sdvo_get_pixel_multiplier(DisplayModePtr pMode) { if (pMode->Clock >= 100000) return 1; else if (pMode->Clock >= 50000) return 2; else return 4; } /* Sets the control bus switch to either point at one of the DDC buses or the * PROM. It resets from the DDC bus back to internal registers at the next I2C * STOP. PROM access is terminated by accessing an internal register. */ static void i830_sdvo_set_control_bus_switch(xf86OutputPtr output, CARD8 target) { i830_sdvo_write_cmd(output, SDVO_CMD_SET_CONTROL_BUS_SWITCH, &target, 1); } static Bool i830_sdvo_set_target_input(xf86OutputPtr output, Bool target_0, Bool target_1) { struct i830_sdvo_set_target_input_args targets = {0}; CARD8 status; if (target_0 && target_1) return SDVO_CMD_STATUS_NOTSUPP; if (target_1) targets.target_1 = 1; i830_sdvo_write_cmd(output, SDVO_CMD_SET_TARGET_INPUT, &targets, sizeof(targets)); status = i830_sdvo_read_response(output, NULL, 0); return (status == SDVO_CMD_STATUS_SUCCESS); } /** * Return whether each input is trained. * * This function is making an assumption about the layout of the response, * which should be checked against the docs. */ static Bool i830_sdvo_get_trained_inputs(xf86OutputPtr output, Bool *input_1, Bool *input_2) { struct i830_sdvo_get_trained_inputs_response response; CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_GET_TRAINED_INPUTS, NULL, 0); status = i830_sdvo_read_response(output, &response, sizeof(response)); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; *input_1 = response.input0_trained; *input_2 = response.input1_trained; return TRUE; } static Bool i830_sdvo_get_active_outputs(xf86OutputPtr output, CARD16 *outputs) { CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_GET_ACTIVE_OUTPUTS, NULL, 0); status = i830_sdvo_read_response(output, outputs, sizeof(*outputs)); return (status == SDVO_CMD_STATUS_SUCCESS); } static Bool i830_sdvo_set_active_outputs(xf86OutputPtr output, CARD16 outputs) { CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_SET_ACTIVE_OUTPUTS, &outputs, sizeof(outputs)); status = i830_sdvo_read_response(output, NULL, 0); return (status == SDVO_CMD_STATUS_SUCCESS); } /** * Returns the pixel clock range limits of the current target input in kHz. */ static Bool i830_sdvo_get_input_pixel_clock_range(xf86OutputPtr output, int *clock_min, int *clock_max) { struct i830_sdvo_pixel_clock_range clocks; CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_GET_INPUT_PIXEL_CLOCK_RANGE, NULL, 0); status = i830_sdvo_read_response(output, &clocks, sizeof(clocks)); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; /* Convert the values from units of 10 kHz to kHz. */ *clock_min = clocks.min * 10; *clock_max = clocks.max * 10; return TRUE; } static Bool i830_sdvo_set_target_output(xf86OutputPtr output, CARD16 outputs) { CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_SET_TARGET_OUTPUT, &outputs, sizeof(outputs)); status = i830_sdvo_read_response(output, NULL, 0); return (status == SDVO_CMD_STATUS_SUCCESS); } /** Fetches either input or output timings to *dtd, depending on cmd. */ static Bool i830_sdvo_get_timing(xf86OutputPtr output, CARD8 cmd, struct i830_sdvo_dtd *dtd) { CARD8 status; i830_sdvo_write_cmd(output, cmd, NULL, 0); status = i830_sdvo_read_response(output, &dtd->part1, sizeof(dtd->part1)); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; i830_sdvo_write_cmd(output, cmd + 1, NULL, 0); status = i830_sdvo_read_response(output, &dtd->part2, sizeof(dtd->part2)); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; return TRUE; } static Bool i830_sdvo_get_input_timing(xf86OutputPtr output, struct i830_sdvo_dtd *dtd) { return i830_sdvo_get_timing(output, SDVO_CMD_GET_INPUT_TIMINGS_PART1, dtd); } static Bool i830_sdvo_get_output_timing(xf86OutputPtr output, struct i830_sdvo_dtd *dtd) { return i830_sdvo_get_timing(output, SDVO_CMD_GET_OUTPUT_TIMINGS_PART1, dtd); } /** Sets either input or output timings from *dtd, depending on cmd. */ static Bool i830_sdvo_set_timing(xf86OutputPtr output, CARD8 cmd, struct i830_sdvo_dtd *dtd) { CARD8 status; i830_sdvo_write_cmd(output, cmd, &dtd->part1, sizeof(dtd->part1)); status = i830_sdvo_read_response(output, NULL, 0); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; i830_sdvo_write_cmd(output, cmd + 1, &dtd->part2, sizeof(dtd->part2)); status = i830_sdvo_read_response(output, NULL, 0); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; return TRUE; } static Bool i830_sdvo_set_input_timing(xf86OutputPtr output, struct i830_sdvo_dtd *dtd) { return i830_sdvo_set_timing(output, SDVO_CMD_SET_INPUT_TIMINGS_PART1, dtd); } static Bool i830_sdvo_set_output_timing(xf86OutputPtr output, struct i830_sdvo_dtd *dtd) { return i830_sdvo_set_timing(output, SDVO_CMD_SET_OUTPUT_TIMINGS_PART1, dtd); } #if 0 static Bool i830_sdvo_create_preferred_input_timing(xf86OutputPtr output, CARD16 clock, CARD16 width, CARD16 height) { struct i830_sdvo_priv *dev_priv = output->dev_priv; struct i830_sdvo_preferred_input_timing_args args; args.clock = clock; args.width = width; args.height = height; i830_sdvo_write_cmd(output, SDVO_CMD_CREATE_PREFERRED_INPUT_TIMING, &args, sizeof(args)); status = i830_sdvo_read_response(output, NULL, 0); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; return TRUE; } static Bool i830_sdvo_get_preferred_input_timing(I830OutputPtr output, struct i830_sdvo_dtd *dtd) { struct i830_sdvo_priv *dev_priv = output->dev_priv; i830_sdvo_write_cmd(output, SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART1, NULL, 0); status = i830_sdvo_read_response(output, &dtd->part1, sizeof(dtd->part1)); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; i830_sdvo_write_cmd(output, SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART2, NULL, 0); status = i830_sdvo_read_response(output, &dtd->part2, sizeof(dtd->part2)); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; return TRUE; } #endif /** Returns the SDVO_CLOCK_RATE_MULT_* for the current clock multiplier */ static int i830_sdvo_get_clock_rate_mult(xf86OutputPtr output) { I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; CARD8 response; CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_GET_CLOCK_RATE_MULT, NULL, 0); status = i830_sdvo_read_response(output, &response, 1); if (status != SDVO_CMD_STATUS_SUCCESS) { xf86DrvMsg(dev_priv->d.pI2CBus->scrnIndex, X_ERROR, "Couldn't get SDVO clock rate multiplier\n"); return SDVO_CLOCK_RATE_MULT_1X; } else { xf86DrvMsg(dev_priv->d.pI2CBus->scrnIndex, X_INFO, "Current clock rate multiplier: %d\n", response); } return response; } /** * Sets the current clock multiplier. * * This has to match with the settings in the DPLL/SDVO reg when the output * is actually turned on. */ static Bool i830_sdvo_set_clock_rate_mult(xf86OutputPtr output, CARD8 val) { CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_SET_CLOCK_RATE_MULT, &val, 1); status = i830_sdvo_read_response(output, NULL, 0); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; return TRUE; } static Bool i830_sdvo_mode_fixup(xf86OutputPtr output, DisplayModePtr mode, DisplayModePtr adjusted_mode) { /* Make the CRTC code factor in the SDVO pixel multiplier. The SDVO * device will be told of the multiplier during mode_set. */ adjusted_mode->Clock *= i830_sdvo_get_pixel_multiplier(mode); return TRUE; } static void i830_sdvo_mode_set(xf86OutputPtr output, DisplayModePtr mode, DisplayModePtr adjusted_mode) { ScrnInfoPtr pScrn = output->scrn; I830Ptr pI830 = I830PTR(pScrn); I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; xf86CrtcPtr crtc = output->crtc; I830CrtcPrivatePtr intel_crtc = crtc->driver_private; CARD32 sdvox; int sdvo_pixel_multiply; CARD16 width, height; CARD16 h_blank_len, h_sync_len, v_blank_len, v_sync_len; CARD16 h_sync_offset, v_sync_offset; struct i830_sdvo_dtd output_dtd; CARD16 no_outputs; no_outputs = 0; if (!mode) return; width = mode->CrtcHDisplay; height = mode->CrtcVDisplay; /* do some mode translations */ h_blank_len = mode->CrtcHBlankEnd - mode->CrtcHBlankStart; h_sync_len = mode->CrtcHSyncEnd - mode->CrtcHSyncStart; v_blank_len = mode->CrtcVBlankEnd - mode->CrtcVBlankStart; v_sync_len = mode->CrtcVSyncEnd - mode->CrtcVSyncStart; h_sync_offset = mode->CrtcHSyncStart - mode->CrtcHBlankStart; v_sync_offset = mode->CrtcVSyncStart - mode->CrtcVBlankStart; output_dtd.part1.clock = mode->Clock / 10; output_dtd.part1.h_active = width & 0xff; output_dtd.part1.h_blank = h_blank_len & 0xff; output_dtd.part1.h_high = (((width >> 8) & 0xf) << 4) | ((h_blank_len >> 8) & 0xf); output_dtd.part1.v_active = height & 0xff; output_dtd.part1.v_blank = v_blank_len & 0xff; output_dtd.part1.v_high = (((height >> 8) & 0xf) << 4) | ((v_blank_len >> 8) & 0xf); output_dtd.part2.h_sync_off = h_sync_offset; output_dtd.part2.h_sync_width = h_sync_len & 0xff; output_dtd.part2.v_sync_off_width = (v_sync_offset & 0xf) << 4 | (v_sync_len & 0xf); output_dtd.part2.sync_off_width_high = ((h_sync_offset & 0x300) >> 2) | ((h_sync_len & 0x300) >> 4) | ((v_sync_offset & 0x30) >> 2) | ((v_sync_len & 0x30) >> 4); output_dtd.part2.dtd_flags = 0x18; if (mode->Flags & V_PHSYNC) output_dtd.part2.dtd_flags |= 0x2; if (mode->Flags & V_PVSYNC) output_dtd.part2.dtd_flags |= 0x4; output_dtd.part2.sdvo_flags = 0; output_dtd.part2.v_sync_off_high = v_sync_offset & 0xc0; output_dtd.part2.reserved = 0; /* Set the output timing to the screen */ i830_sdvo_set_target_output(output, dev_priv->active_outputs); i830_sdvo_set_output_timing(output, &output_dtd); /* Set the input timing to the screen. Assume always input 0. */ i830_sdvo_set_target_input(output, TRUE, FALSE); /* We would like to use i830_sdvo_create_preferred_input_timing() to * provide the device with a timing it can support, if it supports that * feature. However, presumably we would need to adjust the CRTC to output * the preferred timing, and we don't support that currently. */ #if 0 success = i830_sdvo_create_preferred_input_timing(output, clock, width, height); if (success) { struct i830_sdvo_dtd *input_dtd; i830_sdvo_get_preferred_input_timing(output, &input_dtd); i830_sdvo_set_input_timing(output, &input_dtd); } #else i830_sdvo_set_input_timing(output, &output_dtd); #endif switch (i830_sdvo_get_pixel_multiplier(mode)) { case 1: i830_sdvo_set_clock_rate_mult(output, SDVO_CLOCK_RATE_MULT_1X); break; case 2: i830_sdvo_set_clock_rate_mult(output, SDVO_CLOCK_RATE_MULT_2X); break; case 4: i830_sdvo_set_clock_rate_mult(output, SDVO_CLOCK_RATE_MULT_4X); break; } /* Set the SDVO control regs. */ sdvox = INREG(dev_priv->output_device); switch (dev_priv->output_device) { case SDVOB: sdvox &= SDVOB_PRESERVE_MASK; break; case SDVOC: sdvox &= SDVOC_PRESERVE_MASK; break; } sdvox |= (9 << 19) | SDVO_BORDER_ENABLE; if (intel_crtc->pipe == 1) sdvox |= SDVO_PIPE_B_SELECT; sdvo_pixel_multiply = i830_sdvo_get_pixel_multiplier(mode); if (IS_I965G(pI830)) { /* done in crtc_mode_set as the dpll_md reg must be written early */ } else if (IS_I945G(pI830) || IS_I945GM(pI830)) { /* done in crtc_mode_set as it lives inside the dpll register */ } else { sdvox |= (sdvo_pixel_multiply - 1) << SDVO_PORT_MULTIPLY_SHIFT; } OUTREG(dev_priv->output_device, sdvox); } static void i830_sdvo_dpms(xf86OutputPtr output, int mode) { ScrnInfoPtr pScrn = output->scrn; I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; I830Ptr pI830 = I830PTR(pScrn); CARD32 temp; if (mode != DPMSModeOn) { i830_sdvo_set_active_outputs(output, 0); temp = INREG(dev_priv->output_device); if ((temp & SDVO_ENABLE) != 0) OUTREG(dev_priv->output_device, temp & ~SDVO_ENABLE); } else { Bool input1, input2; int i; CARD8 status; temp = INREG(dev_priv->output_device); if ((temp & SDVO_ENABLE) == 0) { OUTREG(dev_priv->output_device, temp | SDVO_ENABLE); #if 0 /* Do it again! If we remove this below register write, or the exact * same one 2 lines up, the mac mini SDVO output doesn't turn on. */ OUTREG(dev_priv->output_device, INREG(dev_priv->output_device) | SDVO_ENABLE); #endif } for (i = 0; i < 2; i++) i830WaitForVblank(pScrn); status = i830_sdvo_get_trained_inputs(output, &input1, &input2); /* Warn if the device reported failure to sync. */ if (status == SDVO_CMD_STATUS_SUCCESS && !input1) { xf86DrvMsg(pScrn->scrnIndex, X_ERROR, "First %s output reported failure to sync\n", SDVO_NAME(dev_priv)); } i830_sdvo_set_active_outputs(output, dev_priv->active_outputs); } } static void i830_sdvo_save(xf86OutputPtr output) { ScrnInfoPtr pScrn = output->scrn; I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; I830Ptr pI830 = I830PTR(pScrn); int o; /* XXX: We should save the in/out mapping. */ dev_priv->save_sdvo_mult = i830_sdvo_get_clock_rate_mult(output); i830_sdvo_get_active_outputs(output, &dev_priv->save_active_outputs); if (dev_priv->caps.sdvo_inputs_mask & 0x1) { i830_sdvo_set_target_input(output, TRUE, FALSE); i830_sdvo_get_input_timing(output, &dev_priv->save_input_dtd_1); } if (dev_priv->caps.sdvo_inputs_mask & 0x2) { i830_sdvo_set_target_input(output, FALSE, TRUE); i830_sdvo_get_input_timing(output, &dev_priv->save_input_dtd_2); } for (o = SDVO_OUTPUT_FIRST; o <= SDVO_OUTPUT_LAST; o++) { CARD16 this_output = (1 << o); if (dev_priv->caps.output_flags & this_output) { i830_sdvo_set_target_output(output, this_output); i830_sdvo_get_output_timing(output, &dev_priv->save_output_dtd[o]); } } dev_priv->save_SDVOX = INREG(dev_priv->output_device); } static void i830_sdvo_restore(xf86OutputPtr output) { ScrnInfoPtr pScrn = output->scrn; I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; I830Ptr pI830 = I830PTR(pScrn); int o; int i; Bool input1, input2; CARD8 status; i830_sdvo_set_active_outputs(output, 0); for (o = SDVO_OUTPUT_FIRST; o <= SDVO_OUTPUT_LAST; o++) { CARD16 this_output = (1 << o); if (dev_priv->caps.output_flags & this_output) { i830_sdvo_set_target_output(output, this_output); i830_sdvo_set_output_timing(output, &dev_priv->save_output_dtd[o]); } } if (dev_priv->caps.sdvo_inputs_mask & 0x1) { i830_sdvo_set_target_input(output, TRUE, FALSE); i830_sdvo_set_input_timing(output, &dev_priv->save_input_dtd_1); } if (dev_priv->caps.sdvo_inputs_mask & 0x2) { i830_sdvo_set_target_input(output, FALSE, TRUE); i830_sdvo_set_input_timing(output, &dev_priv->save_input_dtd_2); } i830_sdvo_set_clock_rate_mult(output, dev_priv->save_sdvo_mult); OUTREG(dev_priv->output_device, dev_priv->save_SDVOX); if (dev_priv->save_SDVOX & SDVO_ENABLE) { for (i = 0; i < 2; i++) i830WaitForVblank(pScrn); status = i830_sdvo_get_trained_inputs(output, &input1, &input2); if (status == SDVO_CMD_STATUS_SUCCESS && !input1) xf86DrvMsg(pScrn->scrnIndex, X_ERROR, "First %s output reported failure to sync\n", SDVO_NAME(dev_priv)); } i830_sdvo_set_active_outputs(output, dev_priv->save_active_outputs); } static int i830_sdvo_mode_valid(xf86OutputPtr output, DisplayModePtr pMode) { I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; if (pMode->Flags & V_DBLSCAN) return MODE_NO_DBLESCAN; if (dev_priv->pixel_clock_min > pMode->Clock) return MODE_CLOCK_HIGH; if (dev_priv->pixel_clock_max < pMode->Clock) return MODE_CLOCK_LOW; return MODE_OK; } static Bool i830_sdvo_get_capabilities(xf86OutputPtr output, struct i830_sdvo_caps *caps) { CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_GET_DEVICE_CAPS, NULL, 0); status = i830_sdvo_read_response(output, caps, sizeof(*caps)); if (status != SDVO_CMD_STATUS_SUCCESS) return FALSE; return TRUE; } /** Forces the device over to the real I2C bus and uses its GetByte */ static Bool i830_sdvo_ddc_i2c_get_byte(I2CDevPtr d, I2CByte *data, Bool last) { xf86OutputPtr output = d->pI2CBus->DriverPrivate.ptr; I830OutputPrivatePtr intel_output = output->driver_private; I2CBusPtr i2cbus = intel_output->pI2CBus, savebus; Bool ret; savebus = d->pI2CBus; d->pI2CBus = i2cbus; ret = i2cbus->I2CGetByte(d, data, last); d->pI2CBus = savebus; return ret; } /** Forces the device over to the real I2C bus and uses its PutByte */ static Bool i830_sdvo_ddc_i2c_put_byte(I2CDevPtr d, I2CByte c) { xf86OutputPtr output = d->pI2CBus->DriverPrivate.ptr; I830OutputPrivatePtr intel_output = output->driver_private; I2CBusPtr i2cbus = intel_output->pI2CBus, savebus; Bool ret; savebus = d->pI2CBus; d->pI2CBus = i2cbus; ret = i2cbus->I2CPutByte(d, c); d->pI2CBus = savebus; return ret; } /** * Sets the control bus over to DDC before sending the start on the real I2C * bus. * * The control bus will flip back at the stop following the start executed * here. */ static Bool i830_sdvo_ddc_i2c_start(I2CBusPtr b, int timeout) { xf86OutputPtr output = b->DriverPrivate.ptr; I830OutputPrivatePtr intel_output = output->driver_private; I2CBusPtr i2cbus = intel_output->pI2CBus; i830_sdvo_set_control_bus_switch(output, SDVO_CONTROL_BUS_DDC2); return i2cbus->I2CStart(i2cbus, timeout); } /** Forces the device over to the real SDVO bus and sends a stop to it. */ static void i830_sdvo_ddc_i2c_stop(I2CDevPtr d) { xf86OutputPtr output = d->pI2CBus->DriverPrivate.ptr; I830OutputPrivatePtr intel_output = output->driver_private; I2CBusPtr i2cbus = intel_output->pI2CBus, savebus; savebus = d->pI2CBus; d->pI2CBus = i2cbus; i2cbus->I2CStop(d); d->pI2CBus = savebus; } /** * Mirrors xf86i2c I2CAddress, using the bus's (wrapped) methods rather than * the default methods. * * This ensures that our start commands always get wrapped with control bus * switches. xf86i2c should probably be fixed to do this. */ static Bool i830_sdvo_ddc_i2c_address(I2CDevPtr d, I2CSlaveAddr addr) { if (d->pI2CBus->I2CStart(d->pI2CBus, d->StartTimeout)) { if (d->pI2CBus->I2CPutByte(d, addr & 0xFF)) { if ((addr & 0xF8) != 0xF0 && (addr & 0xFE) != 0x00) return TRUE; if (d->pI2CBus->I2CPutByte(d, (addr >> 8) & 0xFF)) return TRUE; } d->pI2CBus->I2CStop(d); } return FALSE; } static void i830_sdvo_dump_cmd(xf86OutputPtr output, int opcode) { CARD8 response[8]; i830_sdvo_write_cmd(output, opcode, NULL, 0); i830_sdvo_read_response(output, response, 8); } static void i830_sdvo_dump_device(xf86OutputPtr output) { I830OutputPrivatePtr intel_output = output->driver_private; struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; ErrorF("Dump %s\n", dev_priv->d.DevName); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_DEVICE_CAPS); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_FIRMWARE_REV); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_TRAINED_INPUTS); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_ACTIVE_OUTPUTS); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_IN_OUT_MAP); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_ATTACHED_DISPLAYS); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_HOT_PLUG_SUPPORT); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_ACTIVE_HOT_PLUG); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_INTERRUPT_EVENT_SOURCE); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_INPUT_TIMINGS_PART1); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_INPUT_TIMINGS_PART2); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_OUTPUT_TIMINGS_PART1); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_OUTPUT_TIMINGS_PART2); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART1); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART2); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_INPUT_PIXEL_CLOCK_RANGE); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_OUTPUT_PIXEL_CLOCK_RANGE); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_SUPPORTED_CLOCK_RATE_MULTS); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_CLOCK_RATE_MULT); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_SUPPORTED_TV_FORMATS); i830_sdvo_dump_cmd(output, SDVO_CMD_GET_TV_FORMAT); } void i830_sdvo_dump(ScrnInfoPtr pScrn) { xf86CrtcConfigPtr xf86_config = XF86_CRTC_CONFIG_PTR(pScrn); int i; for (i = 0; i < xf86_config->num_output; i++) { xf86OutputPtr output = xf86_config->output[i]; I830OutputPrivatePtr intel_output = output->driver_private; if (intel_output->type == I830_OUTPUT_SDVO) i830_sdvo_dump_device(output); } } /** * Asks the SDVO device if any displays are currently connected. * * This interface will need to be augmented, since we could potentially have * multiple displays connected, and the caller will also probably want to know * what type of display is connected. But this is enough for the moment. * * Takes 14ms on average on my i945G. */ static xf86OutputStatus i830_sdvo_detect(xf86OutputPtr output) { CARD8 response[2]; CARD8 status; i830_sdvo_write_cmd(output, SDVO_CMD_GET_ATTACHED_DISPLAYS, NULL, 0); status = i830_sdvo_read_response(output, &response, 2); if (status != SDVO_CMD_STATUS_SUCCESS) return XF86OutputStatusUnknown; if (response[0] != 0 || response[1] != 0) return XF86OutputStatusConnected; else return XF86OutputStatusDisconnected; } static DisplayModePtr i830_sdvo_get_modes(xf86OutputPtr output) { ScrnInfoPtr pScrn = output->scrn; xf86CrtcConfigPtr xf86_config = XF86_CRTC_CONFIG_PTR(pScrn); DisplayModePtr modes; xf86OutputPtr crt; modes = i830_ddc_get_modes(output); if (modes != NULL) return modes; /* Mac mini hack. On this device, I get DDC through the analog, which * load-detects as disconnected. I fail to DDC through the SDVO DDC, * but it does load-detect as connected. So, just steal the DDC bits from * analog when we fail at finding it the right way. */ crt = xf86_config->output[0]; if (crt->funcs->detect(crt) == XF86OutputStatusDisconnected) { return crt->funcs->get_modes(crt); } return NULL; } static void i830_sdvo_destroy (xf86OutputPtr output) { I830OutputPrivatePtr intel_output = output->driver_private; if (intel_output) { struct i830_sdvo_priv *dev_priv = intel_output->dev_priv; xf86DestroyI2CBusRec (intel_output->pDDCBus, FALSE, FALSE); xf86DestroyI2CDevRec (&dev_priv->d, FALSE); xf86DestroyI2CBusRec (dev_priv->d.pI2CBus, TRUE, TRUE); xfree (intel_output); } } static const xf86OutputFuncsRec i830_sdvo_output_funcs = { .dpms = i830_sdvo_dpms, .save = i830_sdvo_save, .restore = i830_sdvo_restore, .mode_valid = i830_sdvo_mode_valid, .mode_fixup = i830_sdvo_mode_fixup, .mode_set = i830_sdvo_mode_set, .detect = i830_sdvo_detect, .get_modes = i830_sdvo_get_modes, .destroy = i830_sdvo_destroy }; void i830_sdvo_init(ScrnInfoPtr pScrn, int output_device) { xf86OutputPtr output; I830OutputPrivatePtr intel_output; struct i830_sdvo_priv *dev_priv; int i; unsigned char ch[0x40]; I2CBusPtr i2cbus = NULL, ddcbus; char name[60]; char *name_prefix; char *name_suffix; output = xf86OutputCreate (pScrn, &i830_sdvo_output_funcs,NULL); if (!output) return; intel_output = xnfcalloc (sizeof (I830OutputPrivateRec) + sizeof (struct i830_sdvo_priv), 1); if (!intel_output) { xf86OutputDestroy (output); return; } output->driver_private = intel_output; output->interlaceAllowed = FALSE; output->doubleScanAllowed = FALSE; dev_priv = (struct i830_sdvo_priv *) (intel_output + 1); intel_output->type = I830_OUTPUT_SDVO; /* While it's the same bus, we just initialize a new copy to avoid trouble * with tracking refcounting ourselves, since the XFree86 DDX bits don't. */ if (output_device == SDVOB) I830I2CInit(pScrn, &i2cbus, GPIOE, "SDVOCTRL_E for SDVOB"); else I830I2CInit(pScrn, &i2cbus, GPIOE, "SDVOCTRL_E for SDVOC"); if (i2cbus == NULL) { xf86OutputDestroy (output); return; } if (output_device == SDVOB) { dev_priv->d.DevName = "SDVO Controller B"; dev_priv->d.SlaveAddr = 0x70; name_suffix="-1"; } else { dev_priv->d.DevName = "SDVO Controller C"; dev_priv->d.SlaveAddr = 0x72; name_suffix="-2"; } dev_priv->d.pI2CBus = i2cbus; dev_priv->d.DriverPrivate.ptr = output; dev_priv->output_device = output_device; if (!xf86I2CDevInit(&dev_priv->d)) { xf86DrvMsg(pScrn->scrnIndex, X_ERROR, "Failed to initialize %s I2C device\n", SDVO_NAME(dev_priv)); xf86OutputDestroy (output); return; } intel_output->pI2CBus = i2cbus; intel_output->dev_priv = dev_priv; /* Read the regs to test if we can talk to the device */ for (i = 0; i < 0x40; i++) { if (!i830_sdvo_read_byte_quiet(output, i, &ch[i])) { xf86DrvMsg(pScrn->scrnIndex, X_INFO, "No SDVO device found on SDVO%c\n", output_device == SDVOB ? 'B' : 'C'); xf86OutputDestroy (output); return; } } /* Set up our wrapper I2C bus for DDC. It acts just like the regular I2C * bus, except that it does the control bus switch to DDC mode before every * Start. While we only need to do it at Start after every Stop after a * Start, extra attempts should be harmless. */ ddcbus = xf86CreateI2CBusRec(); if (ddcbus == NULL) { xf86OutputDestroy (output); return; } if (output_device == SDVOB) ddcbus->BusName = "SDVOB DDC Bus"; else ddcbus->BusName = "SDVOC DDC Bus"; ddcbus->scrnIndex = i2cbus->scrnIndex; ddcbus->I2CGetByte = i830_sdvo_ddc_i2c_get_byte; ddcbus->I2CPutByte = i830_sdvo_ddc_i2c_put_byte; ddcbus->I2CStart = i830_sdvo_ddc_i2c_start; ddcbus->I2CStop = i830_sdvo_ddc_i2c_stop; ddcbus->I2CAddress = i830_sdvo_ddc_i2c_address; ddcbus->DriverPrivate.ptr = output; if (!xf86I2CBusInit(ddcbus)) { xf86OutputDestroy (output); return; } intel_output->pI2CBus = i2cbus; intel_output->pDDCBus = ddcbus; intel_output->dev_priv = dev_priv; i830_sdvo_get_capabilities(output, &dev_priv->caps); memset(&dev_priv->active_outputs, 0, sizeof(dev_priv->active_outputs)); if (dev_priv->caps.output_flags & SDVO_OUTPUT_TMDS0) { dev_priv->active_outputs = SDVO_OUTPUT_TMDS0; output->subpixel_order = SubPixelHorizontalRGB; name_prefix="TMDS"; } else if (dev_priv->caps.output_flags & SDVO_OUTPUT_TMDS1) { dev_priv->active_outputs = SDVO_OUTPUT_TMDS1; output->subpixel_order = SubPixelHorizontalRGB; name_prefix="TMDS"; } else { unsigned char bytes[2]; memcpy (bytes, &dev_priv->caps.output_flags, 2); xf86DrvMsg(intel_output->pI2CBus->scrnIndex, X_ERROR, "%s: No active TMDS outputs (0x%02x%02x)\n", SDVO_NAME(dev_priv), bytes[0], bytes[1]); } strcpy (name, name_prefix); strcat (name, name_suffix); if (!xf86OutputRename (output, name)) { xf86OutputDestroy (output); return; } /* Set the input timing to the screen. Assume always input 0. */ i830_sdvo_set_target_input(output, TRUE, FALSE); i830_sdvo_get_input_pixel_clock_range(output, &dev_priv->pixel_clock_min, &dev_priv->pixel_clock_max); xf86DrvMsg(pScrn->scrnIndex, X_INFO, "%s device VID/DID: %02X:%02X.%02X, " "clock range %.1fMHz - %.1fMHz, " "input 1: %c, input 2: %c, " "output 1: %c, output 2: %c\n", SDVO_NAME(dev_priv), dev_priv->caps.vendor_id, dev_priv->caps.device_id, dev_priv->caps.device_rev_id, dev_priv->pixel_clock_min / 1000.0, dev_priv->pixel_clock_max / 1000.0, (dev_priv->caps.sdvo_inputs_mask & 0x1) ? 'Y' : 'N', (dev_priv->caps.sdvo_inputs_mask & 0x2) ? 'Y' : 'N', dev_priv->caps.output_flags & SDVO_OUTPUT_TMDS0 ? 'Y' : 'N', dev_priv->caps.output_flags & SDVO_OUTPUT_TMDS1 ? 'Y' : 'N'); }