/* * MGA-1064, MGA-G100, MGA-G200, MGA-G400, MGA-G550 RAMDAC driver */ /* $XFree86: xc/programs/Xserver/hw/xfree86/drivers/mga/mga_dacG.c,v 1.54 2003/11/03 05:11:17 tsi Exp $ */ /* * This is a first cut at a non-accelerated version to work with the * new server design (DHD). */ #include "colormapst.h" /* All drivers should typically include these */ #include "xf86.h" #include "xf86_OSproc.h" #include "xf86_ansic.h" /* Drivers for PCI hardware need this */ #include "xf86PciInfo.h" /* Drivers that need to access the PCI config space directly need this */ #include "xf86Pci.h" #include "mga_bios.h" #include "mga_reg.h" #include "mga.h" #include "mga_macros.h" #include "xf86DDC.h" /* * implementation */ #define DACREGSIZE 0x50 /* * Only change bits shown in this mask. Ideally reserved bits should be * zeroed here. Also, don't change the vgaioen bit here since it is * controlled elsewhere. * * XXX These settings need to be checked. */ #define OPTION1_MASK 0xFFFFFEFF #define OPTION2_MASK 0xFFFFFFFF #define OPTION3_MASK 0xFFFFFFFF #define OPTION1_MASK_PRIMARY 0xFFFC0FF static void MGAGRamdacInit(ScrnInfoPtr); static void MGAGSave(ScrnInfoPtr, vgaRegPtr, MGARegPtr, Bool); static void MGAGRestore(ScrnInfoPtr, vgaRegPtr, MGARegPtr, Bool); static Bool MGAGInit(ScrnInfoPtr, DisplayModePtr); static void MGAGLoadPalette(ScrnInfoPtr, int, int*, LOCO*, VisualPtr); static Bool MGAG_i2cInit(ScrnInfoPtr pScrn); /* * MGAGCalcClock - Calculate the PLL settings (m, n, p, s). * * DESCRIPTION * For more information, refer to the Matrox * "MGA1064SG Developer Specification (document 10524-MS-0100). * chapter 5.7.8. "PLLs Clocks Generators" * * PARAMETERS * f_out IN Desired clock frequency. * f_max IN Maximum allowed clock frequency. * m OUT Value of PLL 'm' register. * n OUT Value of PLL 'n' register. * p OUT Value of PLL 'p' register. * s OUT Value of PLL 's' filter register * (pix pll clock only). * * HISTORY * August 18, 1998 - Radoslaw Kapitan * Adapted for G200 DAC * * February 28, 1997 - Guy DESBIEF * Adapted for MGA1064SG DAC. * based on MGACalcClock written by [aem] Andrew E. Mileski */ /* The following values are in kHz */ #define MGA_MIN_VCO_FREQ 50000 #define MGA_MAX_VCO_FREQ 310000 static double MGAGCalcClock ( ScrnInfoPtr pScrn, long f_out, int *best_m, int *best_n, int *p, int *s ) { MGAPtr pMga = MGAPTR(pScrn); int m, n; double f_pll, f_vco; double m_err, calc_f; double ref_freq; int feed_div_min, feed_div_max; int in_div_min, in_div_max; int post_div_max; switch( pMga->Chipset ) { case PCI_CHIP_MGA1064: ref_freq = 14318.18; feed_div_min = 100; feed_div_max = 127; in_div_min = 1; in_div_max = 31; post_div_max = 7; break; case PCI_CHIP_MGAG400: case PCI_CHIP_MGAG550: ref_freq = 27050.5; feed_div_min = 7; feed_div_max = 127; in_div_min = 1; in_div_max = 31; post_div_max = 7; break; case PCI_CHIP_MGAG100: case PCI_CHIP_MGAG100_PCI: case PCI_CHIP_MGAG200: case PCI_CHIP_MGAG200_PCI: default: if (pMga->Bios2.PinID && (pMga->Bios2.VidCtrl & 0x20)) ref_freq = 14318.18; else ref_freq = 27050.5; feed_div_min = 7; feed_div_max = 127; in_div_min = 1; in_div_max = 6; post_div_max = 7; break; } /* Make sure that f_min <= f_out */ if ( f_out < ( MGA_MIN_VCO_FREQ / 8)) f_out = MGA_MIN_VCO_FREQ / 8; /* * f_pll = f_vco / (p+1) * Choose p so that MGA_MIN_VCO_FREQ <= f_vco <= MGA_MAX_VCO_FREQ * we don't have to bother checking for this maximum limit. */ f_vco = ( double ) f_out; for ( *p = 0; *p <= post_div_max && f_vco < MGA_MIN_VCO_FREQ; *p = *p * 2 + 1, f_vco *= 2.0); /* Initial amount of error for frequency maximum */ m_err = f_out; /* Search for the different values of ( m ) */ for ( m = in_div_min ; m <= in_div_max ; m++ ) { /* see values of ( n ) which we can't use */ for ( n = feed_div_min; n <= feed_div_max; n++ ) { calc_f = ref_freq * (n + 1) / (m + 1) ; /* * Pick the closest frequency. */ if ( abs(calc_f - f_vco) < m_err ) { m_err = abs(calc_f - f_vco); *best_m = m; *best_n = n; } } } /* Now all the calculations can be completed */ f_vco = ref_freq * (*best_n + 1) / (*best_m + 1); /* Adjustments for filtering pll feed back */ if ( (50000.0 <= f_vco) && (f_vco < 100000.0) ) *s = 0; if ( (100000.0 <= f_vco) && (f_vco < 140000.0) ) *s = 1; if ( (140000.0 <= f_vco) && (f_vco < 180000.0) ) *s = 2; if ( (180000.0 <= f_vco) ) *s = 3; f_pll = f_vco / ( *p + 1 ); #ifdef DEBUG ErrorF( "f_out_requ =%ld f_pll_real=%.1f f_vco=%.1f n=0x%x m=0x%x p=0x%x s=0x%x\n", f_out, f_pll, f_vco, *best_n, *best_m, *p, *s ); #endif return f_pll; } /* * MGAGSetPCLK - Set the pixel (PCLK) clock. */ static void MGAGSetPCLK( ScrnInfoPtr pScrn, long f_out ) { MGAPtr pMga = MGAPTR(pScrn); MGARegPtr pReg = &pMga->ModeReg; /* Pixel clock values */ int m, n, p, s; if(MGAISGx50(pMga)) { pReg->Clock = f_out; return; } /* Do the calculations for m, n, p and s */ (void) MGAGCalcClock( pScrn, f_out, &m, &n, &p, &s ); /* Values for the pixel clock PLL registers */ pReg->DacRegs[ MGA1064_PIX_PLLC_M ] = m & 0x1F; pReg->DacRegs[ MGA1064_PIX_PLLC_N ] = n & 0x7F; pReg->DacRegs[ MGA1064_PIX_PLLC_P ] = (p & 0x07) | ((s & 0x03) << 3); } /* * MGAGInit */ static Bool MGAGInit(ScrnInfoPtr pScrn, DisplayModePtr mode) { /* * initial values of the DAC registers */ const static unsigned char initDAC[] = { /* 0x00: */ 0, 0, 0, 0, 0, 0, 0x00, 0, /* 0x08: */ 0, 0, 0, 0, 0, 0, 0, 0, /* 0x10: */ 0, 0, 0, 0, 0, 0, 0, 0, /* 0x18: */ 0x00, 0, 0xC9, 0xFF, 0xBF, 0x20, 0x1F, 0x20, /* 0x20: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 0x28: */ 0x00, 0x00, 0x00, 0x00, 0, 0, 0, 0x40, /* 0x30: */ 0x00, 0xB0, 0x00, 0xC2, 0x34, 0x14, 0x02, 0x83, /* 0x38: */ 0x00, 0x93, 0x00, 0x77, 0x00, 0x00, 0x00, 0x3A, /* 0x40: */ 0, 0, 0, 0, 0, 0, 0, 0, /* 0x48: */ 0, 0, 0, 0, 0, 0, 0, 0 }; int i; int hd, hs, he, ht, vd, vs, ve, vt, wd; int BppShift; MGAPtr pMga; MGARegPtr pReg; vgaRegPtr pVga; MGAFBLayout *pLayout; xMODEINFO ModeInfo; ModeInfo.ulDispWidth = mode->HDisplay; ModeInfo.ulDispHeight = mode->VDisplay; ModeInfo.ulFBPitch = mode->HDisplay; ModeInfo.ulBpp = pScrn->bitsPerPixel; ModeInfo.flSignalMode = 0; ModeInfo.ulPixClock = mode->Clock; ModeInfo.ulHFPorch = mode->HSyncStart - mode->HDisplay; ModeInfo.ulHSync = mode->HSyncEnd - mode->HSyncStart; ModeInfo.ulHBPorch = mode->HTotal - mode->HSyncEnd; ModeInfo.ulVFPorch = mode->VSyncStart - mode->VDisplay; ModeInfo.ulVSync = mode->VSyncEnd - mode->VSyncStart; ModeInfo.ulVBPorch = mode->VTotal - mode->VSyncEnd; pMga = MGAPTR(pScrn); pReg = &pMga->ModeReg; pVga = &VGAHWPTR(pScrn)->ModeReg; pLayout = &pMga->CurrentLayout; BppShift = pMga->BppShifts[(pLayout->bitsPerPixel >> 3) - 1]; MGA_NOT_HAL( /* Allocate the DacRegs space if not done already */ if (pReg->DacRegs == NULL) { pReg->DacRegs = xnfcalloc(DACREGSIZE, 1); } for (i = 0; i < DACREGSIZE; i++) { pReg->DacRegs[i] = initDAC[i]; } ); /* MGA_NOT_HAL */ switch(pMga->Chipset) { case PCI_CHIP_MGA1064: pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x04; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x44; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x18; pReg->Option = 0x5F094F21; pReg->Option2 = 0x00000000; break; case PCI_CHIP_MGAG100: case PCI_CHIP_MGAG100_PCI: pReg->DacRegs[ MGAGDAC_XVREFCTRL ] = 0x03; if(pMga->HasSDRAM) { if(pMga->OverclockMem) { /* 220 Mhz */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x06; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x38; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x18; } else { /* 203 Mhz */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x01; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x0E; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x18; } pReg->Option = 0x404991a9; } else { if(pMga->OverclockMem) { /* 143 Mhz */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x06; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x24; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x10; } else { /* 124 Mhz */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x04; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x16; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x08; } pReg->Option = 0x4049d121; } pReg->Option2 = 0x0000007; break; case PCI_CHIP_MGAG400: case PCI_CHIP_MGAG550: #ifdef USEMGAHAL MGA_HAL(break;); #endif if (MGAISGx50(pMga)) break; if(pMga->Dac.maxPixelClock == 360000) { /* G400 MAX */ if(pMga->OverclockMem) { /* 150/200 */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x05; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x42; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x18; pReg->Option3 = 0x019B8419; pReg->Option = 0x50574120; } else { /* 125/166 */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x02; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x1B; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x18; pReg->Option3 = 0x019B8419; pReg->Option = 0x5053C120; } } else { if(pMga->OverclockMem) { /* 125/166 */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x02; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x1B; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x18; pReg->Option3 = 0x019B8419; pReg->Option = 0x5053C120; } else { /* 110/166 */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x13; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x7A; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x08; pReg->Option3 = 0x0190a421; pReg->Option = 0x50044120; } } if(pMga->HasSDRAM) pReg->Option &= ~(1 << 14); pReg->Option2 = 0x01003000; break; case PCI_CHIP_MGAG200: case PCI_CHIP_MGAG200_PCI: default: #ifdef USEMGAHAL MGA_HAL(break;); #endif if(pMga->OverclockMem) { /* 143 Mhz */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x06; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x24; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x10; } else { /* 124 Mhz */ pReg->DacRegs[ MGA1064_SYS_PLL_M ] = 0x04; pReg->DacRegs[ MGA1064_SYS_PLL_N ] = 0x2D; pReg->DacRegs[ MGA1064_SYS_PLL_P ] = 0x19; } pReg->Option2 = 0x00008000; if(pMga->HasSDRAM) pReg->Option = 0x40499121; else pReg->Option = 0x4049cd21; break; } MGA_NOT_HAL( /* must always have the pci retries on but rely on polling to keep them from occuring */ pReg->Option &= ~0x20000000; switch(pLayout->bitsPerPixel) { case 8: pReg->DacRegs[ MGA1064_MUL_CTL ] = MGA1064_MUL_CTL_8bits; break; case 16: pReg->DacRegs[ MGA1064_MUL_CTL ] = MGA1064_MUL_CTL_16bits; if ( (pLayout->weight.red == 5) && (pLayout->weight.green == 5) && (pLayout->weight.blue == 5) ) { pReg->DacRegs[ MGA1064_MUL_CTL ] = MGA1064_MUL_CTL_15bits; } break; case 24: pReg->DacRegs[ MGA1064_MUL_CTL ] = MGA1064_MUL_CTL_24bits; break; case 32: if(pLayout->Overlay8Plus24) { pReg->DacRegs[ MGA1064_MUL_CTL ] = MGA1064_MUL_CTL_32bits; pReg->DacRegs[ MGA1064_COL_KEY_MSK_LSB ] = 0xFF; pReg->DacRegs[ MGA1064_COL_KEY_LSB ] = pMga->colorKey; } else pReg->DacRegs[ MGA1064_MUL_CTL ] = MGA1064_MUL_CTL_32_24bits; break; default: FatalError("MGA: unsupported depth\n"); } ); /* MGA_NOT_HAL */ /* * This will initialize all of the generic VGA registers. */ if (!vgaHWInit(pScrn, mode)) return(FALSE); /* * Here all of the MGA registers get filled in. */ hd = (mode->CrtcHDisplay >> 3) - 1; hs = (mode->CrtcHSyncStart >> 3) - 1; he = (mode->CrtcHSyncEnd >> 3) - 1; ht = (mode->CrtcHTotal >> 3) - 1; vd = mode->CrtcVDisplay - 1; vs = mode->CrtcVSyncStart - 1; ve = mode->CrtcVSyncEnd - 1; vt = mode->CrtcVTotal - 2; /* HTOTAL & 0x7 equal to 0x6 in 8bpp or 0x4 in 24bpp causes strange * vertical stripes */ if((ht & 0x07) == 0x06 || (ht & 0x07) == 0x04) ht++; if (pLayout->bitsPerPixel == 24) wd = (pLayout->displayWidth * 3) >> (4 - BppShift); else wd = pLayout->displayWidth >> (4 - BppShift); pReg->ExtVga[0] = 0; pReg->ExtVga[5] = 0; if (mode->Flags & V_INTERLACE) { pReg->ExtVga[0] = 0x80; pReg->ExtVga[5] = (hs + he - ht) >> 1; wd <<= 1; vt &= 0xFFFE; } pReg->ExtVga[0] |= (wd & 0x300) >> 4; pReg->ExtVga[1] = (((ht - 4) & 0x100) >> 8) | ((hd & 0x100) >> 7) | ((hs & 0x100) >> 6) | (ht & 0x40); pReg->ExtVga[2] = ((vt & 0xc00) >> 10) | ((vd & 0x400) >> 8) | ((vd & 0xc00) >> 7) | ((vs & 0xc00) >> 5) | ((vd & 0x400) >> 3); /* linecomp */ if (pLayout->bitsPerPixel == 24) pReg->ExtVga[3] = (((1 << BppShift) * 3) - 1) | 0x80; else pReg->ExtVga[3] = ((1 << BppShift) - 1) | 0x80; pReg->ExtVga[4] = 0; pVga->CRTC[0] = ht - 4; pVga->CRTC[1] = hd; pVga->CRTC[2] = hd; pVga->CRTC[3] = (ht & 0x1F) | 0x80; pVga->CRTC[4] = hs; pVga->CRTC[5] = ((ht & 0x20) << 2) | (he & 0x1F); pVga->CRTC[6] = vt & 0xFF; pVga->CRTC[7] = ((vt & 0x100) >> 8 ) | ((vd & 0x100) >> 7 ) | ((vs & 0x100) >> 6 ) | ((vd & 0x100) >> 5 ) | ((vd & 0x100) >> 4 ) | /* linecomp */ ((vt & 0x200) >> 4 ) | ((vd & 0x200) >> 3 ) | ((vs & 0x200) >> 2 ); pVga->CRTC[9] = ((vd & 0x200) >> 4) | ((vd & 0x200) >> 3); /* linecomp */ pVga->CRTC[16] = vs & 0xFF; pVga->CRTC[17] = (ve & 0x0F) | 0x20; pVga->CRTC[18] = vd & 0xFF; pVga->CRTC[19] = wd & 0xFF; pVga->CRTC[21] = vd & 0xFF; pVga->CRTC[22] = (vt + 1) & 0xFF; pVga->CRTC[24] = vd & 0xFF; /* linecomp */ MGA_NOT_HAL(pReg->DacRegs[MGA1064_CURSOR_BASE_ADR_LOW] = pMga->FbCursorOffset >> 10); MGA_NOT_HAL(pReg->DacRegs[MGA1064_CURSOR_BASE_ADR_HI] = pMga->FbCursorOffset >> 18); if (pMga->SyncOnGreen) { MGA_NOT_HAL(pReg->DacRegs[MGA1064_GEN_CTL] &= ~0x20); pReg->ExtVga[3] |= 0x40; } /* select external clock */ pVga->MiscOutReg |= 0x0C; MGA_NOT_HAL( if (mode->Flags & V_DBLSCAN) pVga->CRTC[9] |= 0x80; if(MGAISGx50(pMga)) { OUTREG(MGAREG_ZORG, 0); } MGAGSetPCLK(pScrn, mode->Clock); ); /* MGA_NOT_HAL */ /* This disables the VGA memory aperture */ pVga->MiscOutReg &= ~0x02; /* Urgh. Why do we define our own xMODEINFO structure instead * of just passing the blinkin' DisplayModePtr? If we're going to * just cut'n'paste routines from the HALlib, it would be better * just to strip the MacroVision stuff out of the HALlib and release * that, surely? */ /********************* Second Crtc programming **************/ /* Writing values to crtc2[] array */ if (pMga->SecondCrtc) { MGACRTC2Get(pScrn, &ModeInfo); MGACRTC2GetPitch(pScrn, &ModeInfo); MGACRTC2GetDisplayStart(pScrn, &ModeInfo,0,0,0); } return(TRUE); } /* * MGAGLoadPalette */ static void MGAPaletteLoadCallback(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); MGAPaletteInfo *pal = pMga->palinfo; int i; while (!(INREG8(0x1FDA) & 0x08)); for(i = 0; i < 256; i++) { if(pal->update) { outMGAdreg(MGA1064_WADR_PAL, i); outMGAdreg(MGA1064_COL_PAL, pal->red); outMGAdreg(MGA1064_COL_PAL, pal->green); outMGAdreg(MGA1064_COL_PAL, pal->blue); pal->update = FALSE; } pal++; } pMga->PaletteLoadCallback = NULL; } void MGAGLoadPalette( ScrnInfoPtr pScrn, int numColors, int *indices, LOCO *colors, VisualPtr pVisual ){ MGAPtr pMga = MGAPTR(pScrn); if((pMga->CurrentLayout.Overlay8Plus24) && (pVisual->nplanes != 8)) return; if(pMga->Chipset == PCI_CHIP_MGAG400 || pMga->Chipset == PCI_CHIP_MGAG550){ /* load them at the retrace in the block handler instead to work around some problems with static on the screen */ while(numColors--) { pMga->palinfo[*indices].update = TRUE; pMga->palinfo[*indices].red = colors[*indices].red; pMga->palinfo[*indices].green = colors[*indices].green; pMga->palinfo[*indices].blue = colors[*indices].blue; indices++; } pMga->PaletteLoadCallback = MGAPaletteLoadCallback; return; } else { while(numColors--) { outMGAdreg(MGA1064_WADR_PAL, *indices); outMGAdreg(MGA1064_COL_PAL, colors[*indices].red); outMGAdreg(MGA1064_COL_PAL, colors[*indices].green); outMGAdreg(MGA1064_COL_PAL, colors[*indices].blue); indices++; } } } /* * MGAGRestorePalette */ static void MGAGRestorePalette(ScrnInfoPtr pScrn, unsigned char* pntr) { MGAPtr pMga = MGAPTR(pScrn); int i = 768; outMGAdreg(MGA1064_WADR_PAL, 0x00); while(i--) outMGAdreg(MGA1064_COL_PAL, *(pntr++)); } /* * MGAGSavePalette */ static void MGAGSavePalette(ScrnInfoPtr pScrn, unsigned char* pntr) { MGAPtr pMga = MGAPTR(pScrn); int i = 768; outMGAdreg(MGA1064_RADR_PAL, 0x00); while(i--) *(pntr++) = inMGAdreg(MGA1064_COL_PAL); } /* * MGAGRestore * * This function restores a video mode. It basically writes out all of * the registers that have previously been saved. */ static void MGAGRestore(ScrnInfoPtr pScrn, vgaRegPtr vgaReg, MGARegPtr mgaReg, Bool restoreFonts) { int i; MGAPtr pMga = MGAPTR(pScrn); CARD32 optionMask; /* * Pixel Clock needs to be restored regardless if we use * HALLib or not. HALlib doesn't do a good job restoring * VESA modes. MATROX: hint, hint. */ if (MGAISGx50(pMga) && mgaReg->Clock) { /* * With HALlib program only when restoring to console! * To test this we check for Clock == 0. */ MGAG450SetPLLFreq(pScrn, mgaReg->Clock); mgaReg->PIXPLLCSaved = FALSE; } if(!pMga->SecondCrtc) { MGA_NOT_HAL( /* * Code is needed to get things back to bank zero. */ /* restore DAC registers * according to the docs we shouldn't write to reserved regs*/ for (i = 0; i < DACREGSIZE; i++) { if( (i <= 0x03) || (i == 0x07) || (i == 0x0b) || (i == 0x0f) || ((i >= 0x13) && (i <= 0x17)) || (i == 0x1b) || (i == 0x1c) || ((i >= 0x1f) && (i <= 0x29)) || ((i >= 0x30) && (i <= 0x37)) || (MGAISGx50(pMga) && !mgaReg->PIXPLLCSaved && ((i == 0x2c) || (i == 0x2d) || (i == 0x2e) || (i == 0x4c) || (i == 0x4d) || (i == 0x4e)))) continue; outMGAdac(i, mgaReg->DacRegs[i]); } /* Do not set the memory config for primary cards as it should be correct already */ optionMask = (pMga->Primary) ? OPTION1_MASK_PRIMARY : OPTION1_MASK; if (!MGAISGx50(pMga)) { /* restore pci_option register */ pciSetBitsLong(pMga->PciTag, PCI_OPTION_REG, optionMask, mgaReg->Option); if (pMga->Chipset != PCI_CHIP_MGA1064) pciSetBitsLong(pMga->PciTag, PCI_MGA_OPTION2, OPTION2_MASK, mgaReg->Option2); if (pMga->Chipset == PCI_CHIP_MGAG400 || pMga->Chipset == PCI_CHIP_MGAG550) pciSetBitsLong(pMga->PciTag, PCI_MGA_OPTION3, OPTION3_MASK, mgaReg->Option3); } ); /* MGA_NOT_HAL */ #ifdef USEMGAHAL /* * Work around another bug in HALlib: it doesn't restore the * DAC width register correctly. MATROX: hint, hint. */ MGA_HAL( outMGAdac(MGA1064_MUL_CTL,mgaReg->DacRegs[0]); outMGAdac(MGA1064_MISC_CTL,mgaReg->DacRegs[1]); if (!MGAISGx50(pMga)) { outMGAdac(MGA1064_PIX_PLLC_M,mgaReg->DacRegs[2]); outMGAdac(MGA1064_PIX_PLLC_N,mgaReg->DacRegs[3]); outMGAdac(MGA1064_PIX_PLLC_P,mgaReg->DacRegs[4]); } ); #endif /* restore CRTCEXT regs */ for (i = 0; i < 6; i++) OUTREG16(0x1FDE, (mgaReg->ExtVga[i] << 8) | i); /* * This function handles restoring the generic VGA registers. */ vgaHWRestore(pScrn, vgaReg, VGA_SR_MODE | (restoreFonts ? VGA_SR_FONTS : 0)); MGAGRestorePalette(pScrn, vgaReg->DAC); /* * this is needed to properly restore start address */ OUTREG16(0x1FDE, (mgaReg->ExtVga[0] << 8) | 0); } else { /* Second Crtc */ xMODEINFO ModeInfo; MGA_NOT_HAL( /* Enable Dual Head */ MGACRTC2Set(pScrn, &ModeInfo); MGAEnableSecondOutPut(pScrn, &ModeInfo); MGACRTC2SetPitch(pScrn, &ModeInfo); MGACRTC2SetDisplayStart(pScrn, &ModeInfo,0,0,0); for (i = 0x80; i <= 0xa0; i ++) { if (i== 0x8d) { i = 0x8f; continue; } outMGAdac(i, mgaReg->dac2[ i - 0x80]); } ); /* MGA_NOT_HAL */ } #ifdef DEBUG ErrorF("Setting DAC:"); for (i=0; iDacRegs[i]); #else if(!(i%8)) ErrorF("\n%02X: ",i); ErrorF("0x%02X, ", mgaReg->DacRegs[i]); #endif } ErrorF("\nOPTION = %08lX\n", mgaReg->Option); ErrorF("OPTION2 = %08lX\n", mgaReg->Option2); ErrorF("CRTCEXT:"); for (i=0; i<6; i++) ErrorF(" %02X", mgaReg->ExtVga[i]); ErrorF("\n"); #endif } /* * MGAGSave * * This function saves the video state. */ static void MGAGSave(ScrnInfoPtr pScrn, vgaRegPtr vgaReg, MGARegPtr mgaReg, Bool saveFonts) { int i; MGAPtr pMga = MGAPTR(pScrn); /* * Pixel Clock needs to be restored regardless if we use * HALLib or not. HALlib doesn't do a good job restoring * VESA modes (s.o.). MATROX: hint, hint. */ if (MGAISGx50(pMga)) { mgaReg->Clock = MGAG450SavePLLFreq(pScrn); } if(pMga->SecondCrtc == TRUE) { for(i = 0x80; i < 0xa0; i++) mgaReg->dac2[i-0x80] = inMGAdac(i); return; } MGA_NOT_HAL( /* Allocate the DacRegs space if not done already */ if (mgaReg->DacRegs == NULL) { mgaReg->DacRegs = xnfcalloc(DACREGSIZE, 1); } ); /* MGA_NOT_HAL */ /* * Code is needed to get back to bank zero. */ OUTREG16(0x1FDE, 0x0004); /* * This function will handle creating the data structure and filling * in the generic VGA portion. */ vgaHWSave(pScrn, vgaReg, VGA_SR_MODE | (saveFonts ? VGA_SR_FONTS : 0)); MGAGSavePalette(pScrn, vgaReg->DAC); /* * Work around another bug in HALlib: it doesn't restore the * DAC width register correctly. */ #ifdef USEMGAHAL /* * Work around another bug in HALlib: it doesn't restore the * DAC width register correctly (s.o.). MATROX: hint, hint. */ MGA_HAL( if (mgaReg->DacRegs == NULL) { mgaReg->DacRegs = xnfcalloc(MGAISGx50(pMga) ? 2 : 5, 1); } mgaReg->DacRegs[0] = inMGAdac(MGA1064_MUL_CTL); mgaReg->DacRegs[1] = inMGAdac(MGA1064_MISC_CTL); if (!MGAISGx50(pMga)) { mgaReg->DacRegs[2] = inMGAdac(MGA1064_PIX_PLLC_M); mgaReg->DacRegs[3] = inMGAdac(MGA1064_PIX_PLLC_N); mgaReg->DacRegs[4] = inMGAdac(MGA1064_PIX_PLLC_P); } ); #endif MGA_NOT_HAL( /* * The port I/O code necessary to read in the extended registers. */ for (i = 0; i < DACREGSIZE; i++) mgaReg->DacRegs[i] = inMGAdac(i); mgaReg->PIXPLLCSaved = TRUE; mgaReg->Option = pciReadLong(pMga->PciTag, PCI_OPTION_REG); mgaReg->Option2 = pciReadLong(pMga->PciTag, PCI_MGA_OPTION2); if (pMga->Chipset == PCI_CHIP_MGAG400 || pMga->Chipset == PCI_CHIP_MGAG550) mgaReg->Option3 = pciReadLong(pMga->PciTag, PCI_MGA_OPTION3); ); /* MGA_NOT_HAL */ for (i = 0; i < 6; i++) { OUTREG8(0x1FDE, i); mgaReg->ExtVga[i] = INREG8(0x1FDF); } #ifdef DEBUG ErrorF("Saved values:\nDAC:"); for (i=0; iDacRegs[i]); #else if(!(i%8)) ErrorF("\n%02X: ",i); ErrorF("0x%02X, ", mgaReg->DacRegs[i]); #endif } ErrorF("\nOPTION = %08lX\n:", mgaReg->Option); ErrorF("OPTION2 = %08lX\nCRTCEXT:", mgaReg->Option2); for (i=0; i<6; i++) ErrorF(" %02X", mgaReg->ExtVga[i]); ErrorF("\n"); #endif } /**** *** HW Cursor */ static void MGAGLoadCursorImage(ScrnInfoPtr pScrn, unsigned char *src) { MGAPtr pMga = MGAPTR(pScrn); CARD32 *dst = (CARD32*)(pMga->FbBase + pMga->FbCursorOffset); int i = 128; /* swap bytes in each line */ while( i-- ) { *dst++ = (src[4] << 24) | (src[5] << 16) | (src[6] << 8) | src[7]; *dst++ = (src[0] << 24) | (src[1] << 16) | (src[2] << 8) | src[3]; src += 8; } } static void MGAGShowCursor(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); /* Enable cursor - X-Windows mode */ outMGAdac(MGA1064_CURSOR_CTL, 0x03); } static void MGAGShowCursorG100(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); /* Enable cursor - X-Windows mode */ outMGAdac(MGA1064_CURSOR_CTL, 0x01); } static void MGAGHideCursor(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); /* Disable cursor */ outMGAdac(MGA1064_CURSOR_CTL, 0x00); } static void MGAGSetCursorPosition(ScrnInfoPtr pScrn, int x, int y) { MGAPtr pMga = MGAPTR(pScrn); x += 64; y += 64; #ifdef USEMGAHAL MGA_HAL( x += pMga->HALGranularityOffX; y += pMga->HALGranularityOffY; ); #endif /* cursor update must never occurs during a retrace period (pp 4-160) */ while( INREG( MGAREG_Status ) & 0x08 ); /* Output position - "only" 12 bits of location documented */ OUTREG8( RAMDAC_OFFSET + MGA1064_CUR_XLOW, (x & 0xFF)); OUTREG8( RAMDAC_OFFSET + MGA1064_CUR_XHI, (x & 0xF00) >> 8); OUTREG8( RAMDAC_OFFSET + MGA1064_CUR_YLOW, (y & 0xFF)); OUTREG8( RAMDAC_OFFSET + MGA1064_CUR_YHI, (y & 0xF00) >> 8); } static void MGAGSetCursorColors(ScrnInfoPtr pScrn, int bg, int fg) { MGAPtr pMga = MGAPTR(pScrn); /* Background color */ outMGAdac(MGA1064_CURSOR_COL0_RED, (bg & 0x00FF0000) >> 16); outMGAdac(MGA1064_CURSOR_COL0_GREEN, (bg & 0x0000FF00) >> 8); outMGAdac(MGA1064_CURSOR_COL0_BLUE, (bg & 0x000000FF)); /* Foreground color */ outMGAdac(MGA1064_CURSOR_COL1_RED, (fg & 0x00FF0000) >> 16); outMGAdac(MGA1064_CURSOR_COL1_GREEN, (fg & 0x0000FF00) >> 8); outMGAdac(MGA1064_CURSOR_COL1_BLUE, (fg & 0x000000FF)); } static void MGAGSetCursorColorsG100(ScrnInfoPtr pScrn, int bg, int fg) { MGAPtr pMga = MGAPTR(pScrn); /* Background color */ outMGAdac(MGA1064_CURSOR_COL1_RED, (bg & 0x00FF0000) >> 16); outMGAdac(MGA1064_CURSOR_COL1_GREEN, (bg & 0x0000FF00) >> 8); outMGAdac(MGA1064_CURSOR_COL1_BLUE, (bg & 0x000000FF)); /* Foreground color */ outMGAdac(MGA1064_CURSOR_COL2_RED, (fg & 0x00FF0000) >> 16); outMGAdac(MGA1064_CURSOR_COL2_GREEN, (fg & 0x0000FF00) >> 8); outMGAdac(MGA1064_CURSOR_COL2_BLUE, (fg & 0x000000FF)); } static Bool MGAGUseHWCursor(ScreenPtr pScrn, CursorPtr pCurs) { MGAPtr pMga = MGAPTR(xf86Screens[pScrn->myNum]); /* This needs to detect if its on the second dac */ if( XF86SCRNINFO(pScrn)->currentMode->Flags & V_DBLSCAN ) return FALSE; if( pMga->SecondCrtc == TRUE ) return FALSE; return TRUE; } /* * According to mga-1064g.pdf pp215-216 (4-179 & 4-180) the low bits of * XGENIODATA and XGENIOCTL are connected to the 4 DDC pins, but don't say * which VGA line is connected to each DDC pin, so I've had to guess. * * DDC1 support only requires DDC_SDA_MASK, * DDC2 support reuqiers DDC_SDA_MASK and DDC_SCL_MASK */ static const int DDC_SDA_MASK = 1 << 1; static const int DDC_SCL_MASK = 1 << 3; static unsigned int MGAG_ddc1Read(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); unsigned char val; /* Define the SDA as an input */ outMGAdacmsk(MGA1064_GEN_IO_CTL, ~(DDC_SCL_MASK | DDC_SDA_MASK), 0); /* wait for Vsync */ while( INREG( MGAREG_Status ) & 0x08 ); while( ! (INREG( MGAREG_Status ) & 0x08) ); /* Get the result */ val = (inMGAdac(MGA1064_GEN_IO_DATA) & DDC_SDA_MASK); return val; } static void MGAG_I2CGetBits(I2CBusPtr b, int *clock, int *data) { MGAPtr pMga = MGAPTR(xf86Screens[b->scrnIndex]); unsigned char val; /* Get the result. */ val = inMGAdac(MGA1064_GEN_IO_DATA); *clock = (val & DDC_SCL_MASK) != 0; *data = (val & DDC_SDA_MASK) != 0; #ifdef DEBUG ErrorF("MGAG_I2CGetBits(%p,...) val=0x%x, returns clock %d, data %d\n", b, val, *clock, *data); #endif } /* * ATTENTION! - the DATA and CLOCK lines need to be tri-stated when * high. Therefore turn off output driver for the line to set line * to high. High signal is maintained by a 15k Ohm pll-up resistor. */ static void MGAG_I2CPutBits(I2CBusPtr b, int clock, int data) { MGAPtr pMga = MGAPTR(xf86Screens[b->scrnIndex]); unsigned char drv, val; val = (clock ? DDC_SCL_MASK : 0) | (data ? DDC_SDA_MASK : 0); drv = ((!clock) ? DDC_SCL_MASK : 0) | ((!data) ? DDC_SDA_MASK : 0); /* Write the values */ outMGAdacmsk(MGA1064_GEN_IO_CTL, ~(DDC_SCL_MASK | DDC_SDA_MASK) , drv); outMGAdacmsk(MGA1064_GEN_IO_DATA, ~(DDC_SCL_MASK | DDC_SDA_MASK) , val); #ifdef DEBUG ErrorF("MGAG_I2CPutBits(%p, %d, %d) val=0x%x\n", b, clock, data, val); #endif } Bool MGAG_i2cInit(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); I2CBusPtr I2CPtr; I2CPtr = xf86CreateI2CBusRec(); if(!I2CPtr) return FALSE; pMga->I2C = I2CPtr; I2CPtr->BusName = "DDC"; I2CPtr->scrnIndex = pScrn->scrnIndex; I2CPtr->I2CPutBits = MGAG_I2CPutBits; I2CPtr->I2CGetBits = MGAG_I2CGetBits; I2CPtr->AcknTimeout = 5; if (!xf86I2CBusInit(I2CPtr)) { return FALSE; } return TRUE; } /* * MGAGRamdacInit * Handle broken G100 special. */ static void MGAGRamdacInit(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); MGARamdacPtr MGAdac = &pMga->Dac; MGAdac->isHwCursor = TRUE; MGAdac->CursorOffscreenMemSize = 1024; MGAdac->CursorMaxWidth = 64; MGAdac->CursorMaxHeight = 64; MGAdac->SetCursorPosition = MGAGSetCursorPosition; MGAdac->LoadCursorImage = MGAGLoadCursorImage; MGAdac->HideCursor = MGAGHideCursor; if ((pMga->Chipset == PCI_CHIP_MGAG100) || (pMga->Chipset == PCI_CHIP_MGAG100)) { MGAdac->SetCursorColors = MGAGSetCursorColorsG100; MGAdac->ShowCursor = MGAGShowCursorG100; } else { MGAdac->SetCursorColors = MGAGSetCursorColors; MGAdac->ShowCursor = MGAGShowCursor; } MGAdac->UseHWCursor = MGAGUseHWCursor; MGAdac->CursorFlags = #if X_BYTE_ORDER == X_LITTLE_ENDIAN HARDWARE_CURSOR_BIT_ORDER_MSBFIRST | #endif HARDWARE_CURSOR_SOURCE_MASK_INTERLEAVE_64 | HARDWARE_CURSOR_TRUECOLOR_AT_8BPP; MGAdac->LoadPalette = MGAGLoadPalette; MGAdac->RestorePalette = MGAGRestorePalette; if ( pMga->Bios2.PinID && pMga->Bios2.PclkMax != 0xFF ) { MGAdac->maxPixelClock = (pMga->Bios2.PclkMax + 100) * 1000; MGAdac->ClockFrom = X_PROBED; } else { switch( pMga->Chipset ) { case PCI_CHIP_MGA1064: if ( pMga->ChipRev < 3 ) MGAdac->maxPixelClock = 170000; else MGAdac->maxPixelClock = 220000; break; case PCI_CHIP_MGAG400: case PCI_CHIP_MGAG550: /* We don't know the new pins format but we know that the maxclock / 4 is where the RamdacType was in the old pins format */ MGAdac->maxPixelClock = pMga->Bios2.RamdacType * 4000; if(MGAdac->maxPixelClock < 300000) MGAdac->maxPixelClock = 300000; break; default: MGAdac->maxPixelClock = 250000; } MGAdac->ClockFrom = X_DEFAULT; } /* Disable interleaving and set the rounding value */ pMga->Interleave = FALSE; pMga->Roundings[0] = 64; pMga->Roundings[1] = 32; pMga->Roundings[2] = 64; pMga->Roundings[3] = 32; /* Clear Fast bitblt flag */ pMga->HasFBitBlt = FALSE; } void MGAGSetupFuncs(ScrnInfoPtr pScrn) { MGAPtr pMga = MGAPTR(pScrn); pMga->PreInit = MGAGRamdacInit; pMga->Save = MGAGSave; pMga->Restore = MGAGRestore; pMga->ModeInit = MGAGInit; pMga->ddc1Read = MGAG_ddc1Read; /* vgaHWddc1SetSpeed will only work if the card is in VGA mode */ pMga->DDC1SetSpeed = vgaHWddc1SetSpeed; pMga->i2cInit = MGAG_i2cInit; }