Drop the outdated configuration options documentation in README.

1 files changed, 0 insertions, 77 deletions

diff --git a/README b/README
index 28727d7..282d6a4 100644
--- a/README
+++ b/README
@@ -20,80 +20,3 @@ For more information on the git code manager, see:
         http://wiki.x.org/wiki/GitPage
 
 ----------------------------------------------------------------------------
-
-What works:
-- Supports 8bpp, 16bpp and 24bpp. Heavy testing on SM720.
-
-XCONFIG options:
-
-The driver supports quite a few different XConfig options, which can
-be used to tune the driver and improve performance. Without any options,
-the driver will use conservative settings which should work on most
-hardware. Large improvements in performance are possible by selecting
-the proper options, which will probably work on most systems.
-
-Cursor:
-
-- "hwcursor" "off" behaves exactly like "swcursor".  Default: "on"
-- "swcursor" will disable the HW Cursor.  HW Cursor is used by default and
-	no option is needed to enable it.
-
-Display:
-
-- "ShadowFB"  Use shadow framebuffer.  Default: off.
-- "Rotate" "cw" | "ccw"  Rotate the screen CW - clockwise or CCW - counter
-    clockwise.  Uses ShadowFB.  Default: no rotation.
-- "UseBIOS"  Use BIOS to set modes.  Default: on.
-- "ZoomOnLCD"  Allow changing resolution on panel.  Default: off.
-
-Overlays:
-
-- "VideoKey"  Set chroma key for video.  Default:  Off blue.
-- "ByteSwap"  Turn on YUV byte swapping.  Defaul: off.
-
-Video memory:
-
-- "set_mclk" sets the memory clock, format is:
-	Option "set_mclk" "50000"
-	in the XF86Config file.  Valid values are any
-	integer <= 100000, where 100000 == 100 MHz.
-
-Acceleration and graphic engine:
-
-- "NoAccel" turns off all acceleration
-- "fifo_aggressive", "fifo_moderate" and "fifo_conservative" alter the settings
-	for the threshold at which the pixel FIFO takes over the internal
-	memory bus to refill itself. The smaller this threshold, the better
-	the acceleration performance of the card. You may try the fastest
-	setting ("aggressive") and move down if you encounter pixel corruption.
-	The optimal setting will probably depend on dot-clock and on color
-	depth. Note that specifying any of these options will also alter other
-	memory settings which should increase performance, so you should at
-        least use "fifo_conservative" (this uses the chip defaults).
-- Common XAA acceleration options to disable primitives for test purposes:
-	"XaaNoScreenToScreenCopy"
-	"XaaNoSolidFillRect"
-	"XaaNoColor8x8PatternFillRect"
-	"XaaNoImageWriteRect"
-	"XaaNoPixmapCache"
-
-PCI bus:
-
-- "pci_burst" will enable PCI burst mode. This should work on all but a
-	few "broken" PCI chipsets, and will increase performance.  Option may
-	take a parameter "on", "off", "yes", etc...
-- "pci_retry" will allow the driver to rely on PCI Retry to program the
-	ViRGE registers. "pci_burst" must be enabled for this to work.
-	This will increase performance, especially for small fills/blits,
-        because the driver does not have to poll the ViRGE before sending it
-        commands to make sure it is ready. It should work on most
-        recent PCI chipsets.
-
-Debug:
-
-- "ShowCache"  Enable or disable viewing offscreen cache memory.  A
-    development debug option.  Default: off.
-
-Header:   //Mercury/Projects/archives/XFree86/4.0/README.-arc   1.2   14 Sep 2000 12:28:36   Frido  $
-
-$XFree86: xc/programs/Xserver/hw/xfree86/drivers/siliconmotion/README,v 1.3 2001/02/15 18:20:33 dawes Exp $