More information about ABLE, including caveats.

3 files changed, 46 insertions, 24 deletions

diff --git a/distrib/notes/cats/install b/distrib/notes/cats/install
index 2b24cca1a1f..688641ad605 100644
--- a/distrib/notes/cats/install
+++ b/distrib/notes/cats/install
@@ -1,4 +1,4 @@
-dnl	$OpenBSD: install,v 1.3 2004/02/08 23:14:30 miod Exp $
+dnl	$OpenBSD: install,v 1.4 2004/02/13 11:00:24 miod Exp $
 OpenBSDInstallPrelude
 
 There are several ways to install OpenBSD onto a disk.  The easiest way
@@ -9,7 +9,8 @@ Booting from CD-ROM installation media:
 
 At the ABLE firmware prompt, enter :
     boot (cd0)bsd.rd
-to boot from the first detected cd-rom drive.
+to boot from the first detected cd-rom drive. If the cd-rom drive has not
+been detected, be sure to put a disk in the tray, and reset the machine.
 
 
 OpenBSDInstallPart2
diff --git a/distrib/notes/cats/prep b/distrib/notes/cats/prep
index 2d501520f18..8175f807150 100644
--- a/distrib/notes/cats/prep
+++ b/distrib/notes/cats/prep
@@ -1,4 +1,4 @@
-dnl	$OpenBSD: prep,v 1.2 2004/02/08 23:12:14 miod Exp $
+dnl	$OpenBSD: prep,v 1.3 2004/02/13 11:00:24 miod Exp $
 To be able to boot the OpenBSD/MACHINE installation program, you will
 need to acquire some limited knowledge of ABLE Firmware, the low-level
 process that controls the microprocessor after hardware initialization
@@ -9,33 +9,52 @@ A complete documentation on the ABLE firmware is available from Simtec at
 the following URL:
   http://www.simtec.co.uk/products/SWABLE/files/able-doc-allset/
 
+
+** Note!
+    You will need ABLE version 1.89 or better in order to be able
+    to boot OpenBSD/MACHINE. Firmware updates are available from
+    Simtec at the following URL:
+      http://www.simtec.co.uk/products/EB110ATX/resources.html
+
+
 For convenience, a few ABLE commands are described below:
 
-boot (hd0)bsd
-	boot the ELF file 'bsd' from the disk partition identified
-	by firmware as hd0.
+	boot (hd0)bsd
+		loads and boots the ELF file 'bsd' from the disk partition
+		identified by firmware as hd0.
 
-nvset variable value
-	sets a firmware environment variable.
+	nvset variable value
+		sets a firmware environment variable.
 
-nvsave
-	saves all variable changes to non-volatile memory.
+	nvsave
+		saves all variable changes to non-volatile memory.
 
-nvclear
-	restores environment variables defaults.
+	nvclear
+		restores environment variables defaults.
 
 The following environment variables control the system startup:
 
-boot.auto
-	when set to "true" (which is its default value), the system will
-	attempt to execute the command set in the "boot.cmd" variable
-	after "boot.timeout" seconds.
-boot.cmd
-	command used to auto-boot, such as "boot (hd0)bsd" to boot the
-	bsd kernel from the first hard disk drive.
-boot.timeout
-	delay until the system boots, in seconds
-
-dnl XXX arguments to kernel
+	boot.auto
+		when set to "true" (which is its default value), the
+		system will attempt to execute the command set in the
+		"boot.cmd" variable after "boot.timeout" seconds, unless
+		the boot process is interrupted by a keypress.
+
+	boot.cmd
+		command used to auto-boot, such as "boot (hd0)bsd" to
+		boot the bsd kernel from the first hard disk partition.
+
+	boot.timeout
+		delay until the system boots, in seconds.
+
+Arguments to the kernel are not passed on the commandline. You can check
+and modify these arguments with the following commands:
+
+	showargs
+		displays the current arguments string.
+
+	setargs value
+		sets the arguments string.
+
 dnl
 dnl XXX bootable partitions
diff --git a/distrib/notes/cats/xfer b/distrib/notes/cats/xfer
index d0f437bce3b..b03a3ee8b22 100644
--- a/distrib/notes/cats/xfer
+++ b/distrib/notes/cats/xfer
@@ -1,8 +1,10 @@
-dnl	$OpenBSD: xfer,v 1.2 2004/02/08 23:12:14 miod Exp $
+dnl	$OpenBSD: xfer,v 1.3 2004/02/13 11:00:24 miod Exp $
 Installation is supported from several media types, including:
 
 	CDROM
 	FFS partitions
+	DOS (FAT) partitions
+	EXT2 partitions
 	Tape
 	FTP
 	HTTP