No need to keep installation notes for architectures we never

have supported.

7 files changed, 0 insertions, 565 deletions

diff --git a/distrib/notes/atari/contents b/distrib/notes/atari/contents
deleted file mode 100644
index 1d2be25d7bd..00000000000
--- a/distrib/notes/atari/contents
+++ /dev/null
@@ -1,61 +0,0 @@
-TopPart
-
-		bins/		atari binary distribution sets;
-				see below.
-
-		floppies/	atari boot and installation
-				floppies; see below.
-
-		utils.openbsd/
-		utils.tos/	Miscellaneous atari
-				installation utilities; see
-				installation section, below.
-
-There are three atari floppy images to be found in the "atari/floppies"
-subdirectory of the OpenBSD OSREV distribution.  One of them is a
-bootable TOS kernel floppy and the other two are installation floppy's.
-They are described in more detail below.  There are gzipped versions
-of each available, for easier downloading.  (The gzipped version
-have the ".gz" extension added to their names.)
-
-Bootable Kernel floppy:
-
-	This TOS disk contains the loadbsd and chg_part programs
-	and the GENERIC kernel.  It is setup so that you can insert it
-	into your floppy drive, and start the programs from GEM.
-
-	This floppy is named boot-OSrev.fs
-
-Installation floppy:
-
-	This disk contains a BSD root file system setup to help
-	you install the rest of OpenBSD.  This includes formatting
-	and mounting your root and /usr partitions and getting
-	ready to extract (and possibly first fetching) the distribution
-	sets.  There is enough on this file system to allow you to
-	make a slip connection, configure an ethernet, mount an NFS
-	file system or ftp.  You can also load distribution sets from
-	a SCSI tape or from one of your existing TOS partitions.
-
-	This floppy's are named "inst-OSrev.fs.1" and "inst-OSrev.fs.2".
-
-DistributionDescription
-
-OpenBSDbase(7M,19M)
-
-OpenBSDcomp(4M,12M)
-
-OpenBSDetc(50K,280K)
-
-OpenBSDgame(1M, 3M)
-
-OpenBSDman(730K,3M)
-
-OpenBSDmisc(2M,6M)
-
-OpenBSDxbase
-
-OpenBSDxfont
-
-OpenBSDxserv
-
diff --git a/distrib/notes/atari/hardware b/distrib/notes/atari/hardware
deleted file mode 100644
index 162d6c26a8e..00000000000
--- a/distrib/notes/atari/hardware
+++ /dev/null
@@ -1,33 +0,0 @@
-OpenBSD/MACHINE OSREV runs on a TT030 and a Falcon. Currently an FPU is
-required, although this might change in the (near) future. The
-minimum amount of RAM required is 4Mb.
-
-Here is a table of recommended HD partition sizes for a full install:
-	partition:	advise,	with X,	needed,	with X
-	root (/)	15M	15M	10M	10M
-	user (/usr)	65M	100M	45M 	80M
-	swap		----- 2M for every M ram -----
-	local (/local)	up to you
-
-As you may note the recommended size of /usr is 20M greater than
-needed. This is to leave room for a kernel source and compile tree
-as you will probably want to compile your own kernel. (GENERIC is
-large and bulky to accommodate all people, BOOT is small and might
-not have all the features you want).
-
-Supported devices {:-include-:}:
-	- The built-in SCSI host adapter
-		- Should support most SCSI-drives. The drives that are
-		  currently tested are:
-			MAXTOR 7245S, MAXTOR 7080S, SEAGATE ST157N
-		- Should support most tape drives. The drives that are
-		  currently tested are:
-			TANDBERG 3600
-		- Should support most CD-ROM drives.
-	- The buildin video controller
-	- The building (720Kb/1.44Mb) floppydrive
-	- The serial2/modem2 ports
-	- The Falcon FX memory expansion
-	- The atari mouse
-
-If its not on this list, there is no support for it in this release.
diff --git a/distrib/notes/atari/install b/distrib/notes/atari/install
deleted file mode 100644
index 7ccd4c2fe22..00000000000
--- a/distrib/notes/atari/install
+++ /dev/null
@@ -1,272 +0,0 @@
-OpenBSDInstallPrelude
-
-The following is a walk-through of the steps necessary to get OpenBSD
-installed on your hard disk.  If you wish to stop the installation,
-you may hit Control-C at any prompt, but if you do, you'll have to
-begin again from scratch.
-
-	First you need to get yourself into OpenBSD.  This can be
-	done in a couple ways, both of which currently require
-	GEMDOS.
-
-	You can insert the GEMDOS kernel floppy and select
-	the loadbsd program. It will ask for parameters, 
-	supply: '-b bsd'.  You can, of course, also run it
-	from the shell command-line in MiNT:
-
-		loadbsd -b a:/bsd
-
-	You should see the screen clear and some information about
-	your system as the kernel configures the hardware.  Then
-	you will be prompted for a root device.  At this time remove
-	the GEMDOS kernel boot floppy from the drive if present and
-	insert the BSD install floppy 1.  Now type `rd0' to tell the
-	kernel to load the install filesystem into RAMdisk. While
-	While the kernel is loading, it will show a '.' for each
-	track loaded. After loading 80 tracks, it will ask you
-	to insert the next floppy. At this time, insert the BSD
-	install floppy 2 and hit any key. The kernel continuous
-	loading another 40 tracks before it continues to boot.
-
-	The system should continue to boot.  For now ignore WARNING:
-	messages about bad dates in clocks. Eventually you will be
-	be asked to enter the pathname of the shell, just hit
-	return.  After a short while you should see a welcome
-	message and a prompt, asking if you wish to proceed with the
-	installation.
-
-	If you wish to proceed, enter "y" and then return.
-
-	If you have configured your hard drive[s] correctly it
-	should find the drive and partition that you selected to
-	use as your root.
-
-	YOU ARE NOW AT THE POINT OF NO RETURN.  If you confirm that
-	you want to install OpenBSD, your hard drive will be modified,
-	and perhaps its contents scrambled at the whim of the install
-	program.
-
-	If you are sure you want to proceed, enter "yes" at the
-	prompt.
-
-	The install program will now make the root filesystem you
-	specified.  There should be only one error in this section
-	of the installation.  It will look like so:
-
-		newfs: ioctl (WDINFO): Invalid argument
-		newfs: /dev/rsd0a: can't rewrite disk label
-
-	If there are any others, restart from the the beginning of
-	the installation process.  This error is ok as the Atari
-	does not write disklabels currently.  You should expect
-	this error whenever using newfs.
-
-	Next the install program will ask you which drive and
-	partition you wish to use as /usr.  First it will list the
-	available drives.  Choose one.  Next it will give you a
-	list of the partitions on that disk along with their sizes,
-	types, etc..  Choose the letter that corresponds to the
-	partition you wish to use for /usr.  To be able to make the
-	proper selection, you need to know, that OpenBSD assigns a
-	special meaning to some of the partition letters:
-	    'a' : root filesystem
-	    'b' : swap partition
-	    'c' : whole disk
-	You should choose a letter in the range 'd'-'p' for your
-	/usr filesystem.  If you are doing a full install this should
-	be a partition that is at least 45M-50M large.  If everything is
-	ok the install program will then format and mount your /usr.  If
-	not then it will ask again for a drive and partition.
-
-	When this completes your root partition will be mounted on
-	/mnt and your /usr partition on /mnt/usr.  An fstab will
-	have been created and initialized to correctly mount these
-	two file systems.  This fstab will be in /mnt/etc.
-
-	What you do from this point on depends on which media you're
-	using to install OpenBSD.  Follow the appropriate instructions,
-	given below.
-
-	To install from an GEMDOS partition:
-
-		You first need to mount the GEMDOS partition
-		using the mount_msdos command.  If e.g. your GEMDOS
-		partition is the first partition on sd0 you could
-		type:
-			
-			mkdir /mnt/gemdos
-			mount_msdos /dev/sd0d /mnt/gemdos
-
-		You can use `disklabel sd0' to find out what types
-		of partitions are on the disk `sd0'.
-
-		Next goto the directory in which you stored the
-		distribution sets.  If e.g. you stored them in the
-		root directory of the partition:
-
-			cd /mnt/gemdos
-
-		When there, run "Set_tmp_dir" and choose the default
-		temporary directory, by hitting return at the
-		prompt.
-
-		Run the "Extract" command, giving it as its sole
-		argument the name of the distribution set you wish
-		to extract.  For example, to extract the base
-		distribution, use the command:
-
-			Extract base20
-
-		and to extract the games distribution:
-
-			Extract game20
-
-		If the distribution sets are in different directories,
-		you will need to cd to each directory in turn, running
-		"Set_tmp_dir" and the appropriate "Extract" command(s).
-
-		Continue this process until you've finished installing
-		all of the sets which you desire to have on your
-		hard disk.  Once you have extracted all sets and
-		are at the "#" prompt again, proceed to the section
-		"Configuring Your System," below.
-
-	To install from tape:
-
-		The first thing you should do is pick a temporary
-		directory where the distribution files can be stored.
-		To do this, use the command "Set_tmp_dir" and enter
-		your choice.  The default is /mnt/usr/distrib.
-
-		After you have picked a temporary directory,
-		you should issue the load command:
-
-			Load_tape
-
-		Next, you will be told to insert the media into
-		the appropriate drive, and hit return.  Continue
-		to follow instructions until you are returned to
-		the "#" prompt.
-
-		Go to the directory which contains the first
-		distribution set you wish to install.  This is
-		either the directory you specified above, or possibly
-		a subdirectory of that directory.
-
-		When there, run "Set_tmp_dir" again, and choose
-		the default temporary directory, by hitting
-		return at the prompt.
-
-		Run the "Extract" command, giving it as its sole
-		argument the name of the distribution set you
-		wish to extract.  For example, to extract the base
-		distribution, use the command:
-
-			Extract base20
-
-		and to extract the games distribution:
-
-			Extract game20
-
-		After the extraction is complete, go to the location
-		of the next set you want to extract, "Set_tmp_dir"
-		again, and once again issue the appropriate
-		extract command.  Continue this process until
-		you've finished installing all of the sets which you
-		desire to have on your hard disk.
-
-		After each set is finished, if you know that you
-		are running low on space you can remove the
-		distribution files for that set by saying:
-
-			rm set_name.??
-
-		For example, if you wish to remove the distribution
-		files for the game09 set, after the "Extract game09"
-		command has completed, issue the command:
-
-			rm game20.??
-
-		Once you have extracted all sets and are at the "#" prompt
-		again, proceed to the section "Configuring Your System,"
-		below.
-
-Configuring Your System:
------------ ---- ------
-
-Once you have finished extracting all of the distribution sets that
-you want on your hard drive and are back at the "#" prompt,
-you are ready to configure your system.
-
-The configuration utility expects that you have installed the base
-system.  If you have not, you will not be able to run it successfully
-(nor will you have a functional system regardless of configuration).
-
-To configure the newly installed operating system, run the
-command "Configure".
-
-Configure will ask for the machine's hostname, domain name, and other
-network configuration information.
-
-Once you have supplied `Configure' all that it requests, your machine
-will be configured well enough that when you reboot it it will
-almost be a completely functional OpenBSD system.  Note you should
-ignore the errors from `chown' they will be corrected shortly.
-
-Once you are done with `Configure', halt the system with the "halt"
-command (wait for "halted" to be displayed) and reboot.  Then again
-boot OpenBSD this time with the command:
-
-	loadbsd bsd
-
-You need to do your final tweaks now.  First mount your file systems
-like so:
-
-	mount -av
-
-Next you need to re-make your devices to get the ownership correct:
-
-	cd /dev
-	./MAKEDEV all
-
-Your system is now complete but not completely configured; you
-should adjust the /etc/sendmail.cf file as necessary to suit your
-site and/or disable sendmail and other network related programs.
-These things can be found in /etc/netstart.  Use vi, if you installed
-the man pages you can type `man vi' or `man ed' for instructions
-on how to use these somewhat non-intuitive editors.
-
-As mentioned at the end of the `Configure' run, you should copy the
-OpenBSD kernel onto the root partition as "/bsd". There is also
-another option to this. As OpenBSD/Atari has to be booted from TOS,
-you could do the following:
-	Reserve a small GEMDOS partition of about 4Mb. This is
-	enough to put in a few kernels. Put the bsd kernel
-	into this partition. Also, edit your /etc/fstab to always
-	mount this partition, say as /kernels. Now make a symlink
-	from /bsd to /kernels/bsd.
-	This scheme is particularly handy when you want to make your
-	own kernel. When compilation is finished, you just copy
-	your kernel to /kernels/bsd and reboot. It's wise to
-	make sure there is _always_ a 'know to work' kernel image
-	present.
-
-To get the proper timezone settings, link /etc/localtime to the
-appropriate file in /usr/share/zoneinfo. The link provided is to
-/usr/share/zoneinfo/US/Pacific.
-
-Once you are done with the rest of configuration unmount your file
-systems and halt your system, then reboot:
-
-	cd /
-	umount -av
-	halt
-	<reboot>
-
-Finally you can now boot your system and it will be completely
-functional:
-
-	loadbsd -a bsd
-
-When it boots off the hard drive, you will have a complete
-OpenBSD system!  CONGRATULATIONS! (You really deserve them!!!)
diff --git a/distrib/notes/atari/prep b/distrib/notes/atari/prep
deleted file mode 100644
index 80705768931..00000000000
--- a/distrib/notes/atari/prep
+++ /dev/null
@@ -1,97 +0,0 @@
-Note you will be modifying your HD's if you mess something up here you
-could lose everything on all the drives that you mess with.  It is
-therefore advised that you:
-
-	Write down your current configurations.  Do this
-	by writing down all partition info (especially their sizes).
-
-	Back up the partitions you are keeping.
-
-What you need to do is partition your drives; creating
-space for at least root, swap and /usr partitions and possibly at
-least one more for /local if you have the space.
-
-The partitioning can be done in two ways, the first method heavily
-relies on the AHDI way of partitioning, the second method nearly
-ignores the AHDI partitioning and gives you far more flexibility.
-Currently, the second method can only be achieved from a working
-OpenBSD/atari system.  How this should be done is described in
-"upgrading to OpenBSD-labeling".
-
-Using AHDI partitioning:
-	The partitioning can be done with the AHDI-disk that is
-	provided with your TT or Falcon. Note that the AHDI partitioning
-	function erases all partitions on your hard disk even if they are
-	not changed!
-	I know this is rather stupid, but don't say I didn't warn you.
-
-	You will need the 'chg_part' program from the boot disk to
-	prepare your hard disk a bit more. This program will change the
-	partition-id so OpenBSD knows which partitions it can use. The
-	synopsis is:
-		chg_part <driveno> <partno> <new_id>
-
-	The drive number corresponds with the drive's SCSI-id. The new
-	id can be selected from one of the following acronyms:
-		NBU - OpenBSD User partition
-		NBR - OpenBSD Root partition
-		NBS - OpenBSD Swap partition
-	Because OpenBSD cannot be bootloaded (yet) and thus must be
-	loaded through GEM, it is unwise to use drive 'C'
-	(drive 0/partition 1) as a OpenBSD partition. When a partition-id
-	is changed, GEMDOS won't be able to recognize your drive, so be
-	warned that the drive labels are shifted afterwards. The chg_part
-	program still recognizes them, take this into account when
-	re-labeling partitions. Also note that the chg_part process is
-	reversible. So don't panic if you made a mistake. Just run
-	chg_part again with the same drive/partition arguments but
-	supplied the original partition id.
-
-Upgrading to OpenBSD-labeling:
-	First of all the new disk label functions are fully backwards
-	compatible with the current (old) behavior, therefore you don't
-	have to rename partition identifiers if you don't want to. The only
-	limitation is that you won't be able to write a disklabel to your
-	harddisk ("Device not configured.").
-
-	If you'd like to have the flexibility of the OpenBSD disk label,
-	the procedure is very simple: change the identifier of the AHDI
-	partition that contains your OpenBSD root filesystem from NBR to NBD.
-	Boot OpenBSD; run `disklabel -e sd?'; disklabel will start vi;
-	quit vi without changing anything; now the disklabel should be
-	written to the NBD partition. If at this point disklabel tells
-	you that one or more of your partitions extend past the end of
-	the unit, then you have an old version of disklabel. Get the
-
-	If you like, you can now change the NBD partition id to RAW
-	(this would for example be necessary if the partition must be
-	shared with MiNT), but keep in mind that the partition id must
-	be either NBD or RAW, otherwise OpenBSD won't be able to find the
-	disklabel. The NBS id (used for a swap partition) is no longer
-	needed, you can change it to whatever you like (or leave it as
-	is, if that's what you like :-) ). The same is true for the
-	NBU id's.
-
-	WARNINGS:
-		- the NBD partition does not necessarily have to be the
-		  partition that contains the OpenBSD root filesystem, but
-		  it *must* be a partition that contains a fast filesystem.
-		  Do *not* try this with a partition that contains a gemdos,
-		  minix or ext2 filesystem; if you do, you'll *loose* a
-		  filesystem.
-		- Now that you have a real disklabel, you can modify it in
-		  (almost) any way you want. However, if you make a mess of
-		  the disk label, OpenBSD may (or may not) make a mess of
-		  your disk! No freedom without responsibility.
-		  OpenBSD will try to warn you for a possibly dangerous
-		  partition table, but it's up to you to either take that
-		  warning serious or ignore it (there may be good reasons
-		  to ignore the warning, if you know what you're doing).
-
-	So what do you do if you have a new disk, that will be exclusively
-	used by OpenBSD? Very simple: don't let it get `infected' by the
-	AHDI `virus'. ,-) Just connect the disk to your TT/Falcon; boot
-	OpenBSD; run `disklabel -e'; you'll see only one large partition `d'
-	(there won't be any filesystem on it yet); you can create partitions
-	in any way you want, as you're no longer limited by an AHDI partition
-	table.
diff --git a/distrib/notes/atari/upgrade b/distrib/notes/atari/upgrade
deleted file mode 100644
index f53c1a87a89..00000000000
--- a/distrib/notes/atari/upgrade
+++ /dev/null
@@ -1,36 +0,0 @@
-Before updating, you probably would want to backup your original
-filesystems!
-
-The update procedure will not overwrite or remove any files not present
-in the sets you install. If you've replaced programs present in the
-distribution, you have to replace them again after you did the update.
-The etc-set needs special caution. You generally don't want to install
-this one when upgrading. It is recommended that you get a copy of this
-set and _carefully_ upgrade your configuration files by hand.
-Before starting the actual procedure, make a note of the partitions your
-root- and usr-filesystems are on. You'll need to mount them by hand.
-
-Ok, let's go. Insert the bootfloppy and follow the 'normal' installation
-procedure until it asks you if you wish to proceed with the installation.
-Now enter 'n' and hit return. You will be left at the shell prompt. Now
-mount your root and usr filesystems on /mnt. If your root-filesystem is
-on sd1a and your usr-filesystem on sd1d this would require the following
-actions:
-	mount_ffs /dev/sd1a /mnt
-	mount_ffs /dev/sd1d /mnt/usr
-
-At this point, you can follow the section "Installing the OpenBSD System"
-to install the sets. There is one difference: When Extract asks you 
-	"Are you installing a -current snapshot? [n]"
-answer 'y'.
-
-Once you are done installing the upgrade sets, then reboot:
-	cd /
-	umount -av
-	halt
-	<reboot>
-
-Now you can boot your upgraded system as usually, but take the
-new kernel! To finish up, you should rebuild your /dev-directory:
-	cd /dev
-	./MAKEDEV all
diff --git a/distrib/notes/atari/whatis b/distrib/notes/atari/whatis
deleted file mode 100644
index de50ed1cae5..00000000000
--- a/distrib/notes/atari/whatis
+++ /dev/null
@@ -1,2 +0,0 @@
-The Atari release stepped in in March 1995. This means the OpenBSD 2.0
-is the first official release of OpenBSD/Atari.
diff --git a/distrib/notes/atari/xfer b/distrib/notes/atari/xfer
deleted file mode 100644
index b5bd75ac3b1..00000000000
--- a/distrib/notes/atari/xfer
+++ /dev/null
@@ -1,64 +0,0 @@
-Installation is supported from several media types, including:
-	TOS HD partitions
-	Tape
-
-No matter what you do, however, you'll need to have three disks handy,
-on which you will put the install and boot floppy images.
-
-All the images are available from the directory "atari/floppies",
-under the root of the OpenBSD tree at your favorite archive site.
-
-If you are using OpenBSD/atari to make the floppies, you should use
-the command dd(1) to write the raw floppy images (.fs files) to
-the disk. To write onto fd0 use:
-
-	dd if=inst-10.fs.1 of=/dev/rfd0b bs=9b
-
-If you are using TOS to make the floppies, grab the 'rawrite' utility
-from the "OSREV/tools" directory and issue the command:
-	rawrite boot-10.fs
-
-This will create the boot-floppy on the floppy in drive a. The floppies
-should be pre-formatted on 720Kb for both the 'dd' and 'rawrite' commands
-to work. Pre-formatting can be best done using the desktop format command.
-Some other utilities seem to be giving problems.
-
-The steps necessary to prepare the distribution sets
-for installation depend on which method of installation
-you choose.  The various methods are explained below.
-
-To prepare for installing via an GEMDOS partition:
-
-	To install OpenBSD from an GEMDOS partition, you need to
-	get the OpenBSD distribution sets you wish to install
-	on your system on to an GEMDOS partition.  All of the
-	set_name.xx pieces can be placed in a single directory
-	instead of separate ones for each distribution set.  This
-	will also simplify the installation work later on.
-
-	Note where you place the files you will need this later.
-
-	Once you have done this, you can proceed to the next
-	step in the installation process, preparing your hard disk.
-
-To prepare for installing via a tape:
-
-	To install OpenBSD from a tape, you need to somehow
-	get the OpenBSD filesets you wish to install on
-	your system on to the appropriate kind of tape,
-	in tar format.
-
-	If you're making the tape on a UN*X system, the easiest
-	way to do so is:
-
-		tar cvf <tape_device> <files>
-
-	where "<tape_device>" is the name of the tape device
-	that describes the tape drive you're using (possibly
-	something like /dev/nrst0, but we make no guarantees 8-).
-	If you can't figure it out, ask your system administrator.
-	"<files>" are the names of the "set_name.nnn" files
-	which you want to be placed on the tape.
-
-	Once you have done this, you can proceed to the next
-	step in the installation process, preparing your hard disk.