Factorize more common texts from the ramdisk operation.

No text changes except for harmonization, and the blurb about network
interface flags has bene slightly changed for some arches.

1 files changed, 17 insertions, 83 deletions

diff --git a/distrib/notes/macppc/install b/distrib/notes/macppc/install
index fafa76f0d13..ea55877cd89 100644
--- a/distrib/notes/macppc/install
+++ b/distrib/notes/macppc/install
@@ -1,3 +1,4 @@
+dnl	$OpenBSD: install,v 1.9 2002/03/30 22:52:57 miod Exp $
 OpenBSDInstallShortPrelude
 
 Before you begin, you should decide if OpenBSD is to be installed
@@ -37,19 +38,7 @@ OpenBSDBootMsgs
 	You will next be asked for your terminal type.  You should just
 	hit return to select the default (vt220).
 
-	Now you will be asked whether you wish to do an "install"
-	or an "upgrade".  Enter 'i' for a fresh install or 'u' to
-	upgrade an existing installation.
-
-	You will be presented with a welcome message and asked if
-	you really wish to install (or upgrade).  Assuming you
-	answered yes, you will be asked which terminal type to use.
-	You should just hit return to select the default (vt220).
-
-	The install program will then tell you which disks of that
-	type it can install on, and ask you which it should use.  The
-	name of the disk is typically "wd0" for IDE/ATA drives or
-	"sd0" for SCSI drives.  Reply with the name of your disk.
+OpenBSDInstallPart3({:- or "wd0" for IDE/ATA drives-:})
 
 	Next you will have to edit or create a disklabel for the disk
 	OpenBSD is being installed on.  If there are any existing
@@ -117,80 +106,25 @@ OpenBSDBootMsgs
 	correct this.  Note that you should make OpenBSD be the active
 	partition at least until the install has been completed.
 
-	Next the disk label which defines the layout of the OpenBSD file
-	systems must be set up.  The installation script will invoke an
-	editor allowing you to do this.  Note that partition 'c' inside
-	this disk label should ALWAYS reflect the entire disk, including
-	any non-OpenBSD portions.  The root file system should be in
-	partition 'a', and swap is usually in partition 'b'.  If you have
-	DOS or Linux partitions defined on the disk, these will usually
-	show up as partition 'h', 'i' and so on.  It is recommended that
-	you create separate partitions for /usr and /var, and if you have
-	room for it, also for /home.  Currently OpenBSD will not share a
-	disk with any other operating system care should be taken not to
-	overwrite any data on other disks in the system and that no data
-	is on the disk to be used for OpenBSD/MACHINE.
+OpenBSDInstallPart4({:-If you have DOS or Linux
+	partitions defined on the disk, these will usually show up as
+	partition 'h', 'i' and so on.
+
+	Currently OpenBSD will not share a disk with any other operating
+	system, so care should be taken not to overwrite any data on other
+	disks in the system and that no data is on the disk to be used
+	for OpenBSD/MACHINE.
 
 	Note that all OpenBSD partitions in the disk label must have an
 	offset that makes it start within the OpenBSD part of the disk,
 	and a size that keeps it inside of that portion of the disk.  This
-	is within the bounds of the 'c' partition.
-
-	The swap partition (usually 'b') should have a type of "swap", all
-	other native OpenBSD partitions should have a type of "4.2BSD".
-	Block and fragment sizes are usually 8192 and 1024 bytes, but can
-	also be 4096 and 512 or even 16384 and 2048 bytes.
-
-	The install program will now label your disk and ask which file
-	systems should be created on which partitions.  It will auto-
-	matically select the 'a' partition to be the root file system.
-	Next it will ask for which disk and partition you want a file
-	system created on.  This will be the same as the disk name (e.g.
-	"sd0") with the letter identifying the partition (e.g. "d")
-	appended (e.g. "sd0d").  Then it will ask where this partition is
-	to be mounted, e.g. /usr.  This process will be repeated until
-	you just hit return.
-
-	At this point you will be asked to confirm that the file system
-	information you have entered is correct, and given an opportunity
-	to change the file system table.  Next it will create the new file
-	systems as specified, OVERWRITING ANY EXISTING DATA.  This is the
-	point of no return.
-
-	After all your file systems have been created, the install program
-	will give you an opportunity to configure the network.  The network
-	configuration you enter (if any) can then be used to do the install
-	from another system using HTTP or FTP, and will also be the
-	configuration used by the system after the installation is complete.
-
-	If you select to configure the network, the install program will
-	ask you for a name of your system and the DNS domain name to use.
-	Note that the host name should be without the domain part, and that
-	the domain name should NOT {:-include-:} the host name part.
-
-	Next the system will give you a list of network interfaces you can
-	configure.  For each network interface you select to configure, it
-	will ask for the IP address to use, the symbolic host name to use,
-	the netmask to use and any interface-specific flags to set.  The
-	interface-specific flags are usually used to determine which media
-	the network card is to use. Supply the appropriate media options
-	as suggested, Typically no media flags are required as autodetect
-	normally works.
-
-	After all network interfaces has been configured the install pro-
-	gram will ask for a default route and IP address of the primary
-	name server to use.  You will also be presented with an opportunity
-	to edit the host table.
-
-	At this point you will be allowed to edit the file system table
-	that will be used for the remainder of the installation and that
-	will be used by the finished system, following which the new file
-	systems will be mounted to complete the installation.
-
-	After these preparatory steps have been completed, you will be
-	able to extract the distribution sets onto your system.  There
-	are several install methods supported; FTP, HTTP, tape, CD-ROM
-	or a local disk partition.
+	is within the bounds of the 'c' partition.-:})
+
+OpenBSDInstallPart5(sd0)
+
+OpenBSDInstallNet
+
+OpenBSDInstallNet2({:-CD-ROM, -:})
 
 OpenBSDFTPInstall