Factorize more common texts from the ramdisk operation.

No text changes except for harmonization, and the blurb about network
interface flags has bene slightly changed for some arches.

1 files changed, 10 insertions, 68 deletions

diff --git a/distrib/notes/mvme68k/install b/distrib/notes/mvme68k/install
index 194e9ca3d54..0a50dc13cfe 100644
--- a/distrib/notes/mvme68k/install
+++ b/distrib/notes/mvme68k/install
@@ -1,3 +1,4 @@
+dnl	$OpenBSD: install,v 1.14 2002/03/30 22:52:58 miod Exp $
 OpenBSDInstallPrelude
 
 There are several ways to install OpenBSD onto a disk. The easiest way
@@ -127,74 +128,15 @@ OpenBSDBootMsgs
 	the terminal type from amongst those listed.
 	(If your terminal type is xterm, just use vt100).
 
-	After entering the terminal type you will be greeted by a
-	welcome message and asked if you really want to continue.
-	Assuming you answered yes, the install program will then tell
-	you which disks of that type it can install on, and ask you
-	which it should use.  The name of the disk is typically "sd0".
-	Reply with the name of your disk.
-
-	Next you will have to edit or create a disklabel for the disk
-	OpenBSD is being installed on.  The installation script will
-	invoke the text editor allowing you to do this.  Note that
-	partition 'c' inside this disk label should ALWAYS reflect the
-	entire disk, including any non-OpenBSD portions.  The root file
-	system should be in partition 'a', and swap is usually in partition
-	'b'.  It is recommended that you create separate partitions for
-	root and /usr, you may also want to specify /var and /home
-	partitions.
-
-	The swap partition (usually 'b') should have a type of "swap", all
-	other native OpenBSD partitions should have a type of "4.2BSD".
-	Block and fragment sizes are usually 8192 and 1024 bytes, but can
-	also be 16384 and 2048 bytes.
-
-	The install program will now label your disk and ask which file
-	systems should be created on which partitions.  It will auto-
-	matically select the 'a' partition to be the root file system.
-	Next it will ask for which disk and partition you want a file
-	system created on.  This will be the same as the disk name (e.g.
-	"sd0") with the letter identifying the partition (e.g. "d")
-	appended (e.g. "sd0d").  Then it will ask where this partition is
-	to be mounted, e.g. /usr.  This process will be repeated until
-	you type "done".
-
-	At this point you will be asked to confirm that the file system
-	information you have entered is correct, and given an opportunity
-	to change the file system table.  Next it will create the new file
-	systems as specified, OVERWRITING ANY EXISTING DATA.  This is the
-	point of no return.
-
-	After all your file systems have been created, the install program
-	will give you an opportunity to configure the network.  The network
-	configuration you enter (if any) can then be used to do the install
-	from another system using NFS, HTTP or FTP, and will also be the
-	configuration used by the system after the installation is complete.
-
-	If you select to configure the network, the install program will
-	ask you for a name of your system and the DNS domain name to use.
-	Note that the host name should be without the domain part, and that
-	the domain name should NOT {:-include-:} the host name part.
-
-	Next the system will give you a list of network interfaces you can
-	configure.  For each network interface you select to configure, it
-	will ask for the IP address to use, the symbolic host name to use,
-	the netmask to use and any media flags to set.
-
-	After all network interfaces have been configured the install pro-
-	gram will ask for a default route and IP address of the primary
-	name server to use.  You will also be presented with an opportunity
-	to edit the host table.
-
-	At this point you will be allowed to edit the file system table
-	that will be used for the remainder of the installation and that
-	will be used by the finished system, following which the new file
-	systems will be mounted to complete the installation.
-
-	After these preparatory steps have been completed, you will be
-	able to extract the distribution sets onto your system.  There
-	are several install methods supported; FTP, HTTP, tape, CD-ROM, NFS
-	or a local disk partition.
+OpenBSDInstallPart3
+
+OpenBSDInstallPart4
+
+OpenBSDInstallPart5(sd0)
+
+OpenBSDInstallNet
+
+OpenBSDInstallNet2({:-CD-ROM, NFS, -:})
 
 OpenBSDFTPInstall