New DS8390/WD83C690 device driver used by ec, ne and we from NetBSD.

3 files changed, 1514 insertions, 12 deletions

diff --git a/sys/dev/ic/dp8390.c b/sys/dev/ic/dp8390.c
new file mode 100644
index 00000000000..2df1fea5ad3
--- /dev/null
+++ b/sys/dev/ic/dp8390.c
@@ -0,0 +1,1336 @@
+/*	$OpenBSD: dp8390.c,v 1.1 1998/09/22 06:41:12 fgsch Exp $	*/
+/*	$NetBSD: dp8390.c,v 1.13 1998/07/05 06:49:11 jonathan Exp $	*/
+
+/*
+ * Device driver for National Semiconductor DS8390/WD83C690 based ethernet
+ * adapters.
+ *
+ * Copyright (c) 1994, 1995 Charles M. Hannum.  All rights reserved.
+ *
+ * Copyright (C) 1993, David Greenman.  This software may be used, modified,
+ * copied, distributed, and sold, in both source and binary form provided that
+ * the above copyright and these terms are retained.  Under no circumstances is
+ * the author responsible for the proper functioning of this software, nor does
+ * the author assume any responsibility for damages incurred with its use.
+ */
+
+#include "bpfilter.h"
+
+#include <sys/param.h>
+#include <sys/systm.h>
+#include <sys/device.h>
+#include <sys/errno.h>
+#include <sys/ioctl.h>
+#include <sys/mbuf.h>
+#include <sys/socket.h>
+#include <sys/syslog.h>
+
+#include <net/if.h>
+#include <net/if_dl.h>
+#include <net/if_types.h>
+#include <net/if_media.h>
+#ifdef __NetBSD__
+#include <net/if_ether.h>
+#endif
+
+#ifdef INET
+#include <netinet/in.h>
+#include <netinet/in_systm.h>
+#include <netinet/in_var.h>
+#include <netinet/ip.h>
+#ifdef __NetBSD__
+#include <netinet/if_inarp.h>
+#else
+#include <netinet/if_ether.h>
+#endif
+#endif
+
+#ifdef NS
+#include <netns/ns.h>
+#include <netns/ns_if.h>
+#endif
+
+#if NBPFILTER > 0
+#include <net/bpf.h>
+#include <net/bpfdesc.h>
+#endif
+
+#include <machine/bus.h>
+
+#include <dev/ic/dp8390reg.h>
+#include <dev/ic/dp8390var.h>
+
+#ifdef DEBUG
+#define __inline__	/* XXX for debugging porpoises */
+#endif
+
+static __inline__ void	dp8390_xmit __P((struct dp8390_softc *));
+
+static __inline__ void	dp8390_read_hdr __P((struct dp8390_softc *,
+			    int, struct dp8390_ring *));
+static __inline__ int	dp8390_ring_copy __P((struct dp8390_softc *,
+			    int, caddr_t, u_short));
+static __inline__ int	dp8390_write_mbuf __P((struct dp8390_softc *,
+			    struct mbuf *, int));
+
+static int		dp8390_test_mem __P((struct dp8390_softc *));
+
+int	dp8390_enable __P((struct dp8390_softc *));
+void	dp8390_disable __P((struct dp8390_softc *));
+
+int	dp8390_mediachange __P((struct ifnet *));
+void	dp8390_mediastatus __P((struct ifnet *, struct ifmediareq *));
+
+#define	ETHER_MIN_LEN	64
+#define ETHER_MAX_LEN	1518
+#define	ETHER_ADDR_LEN	6
+
+int	dp8390_debug = 0;
+
+/*
+ * Do bus-independent setup.
+ */
+int
+dp8390_config(sc, media, nmedia, defmedia)
+	struct dp8390_softc *sc;
+	int *media, nmedia, defmedia;
+{
+#ifdef __NetBSD__
+	struct ifnet *ifp = &sc->sc_ec.ec_if;
+#else
+	struct ifnet *ifp = &sc->sc_arpcom.ac_if;
+#endif
+	int i, rv;
+
+	rv = 1;
+
+	if (!sc->test_mem)
+		sc->test_mem = dp8390_test_mem;
+
+	/* Allocate one xmit buffer if < 16k, two buffers otherwise. */
+	if ((sc->mem_size < 16384) ||
+	    (sc->sc_flags & DP8390_NO_MULTI_BUFFERING))
+		sc->txb_cnt = 1;
+	else
+		sc->txb_cnt = 2;
+
+	sc->tx_page_start = sc->mem_start >> ED_PAGE_SHIFT;
+	sc->rec_page_start = sc->tx_page_start + sc->txb_cnt * ED_TXBUF_SIZE;
+	sc->rec_page_stop = sc->tx_page_start + (sc->mem_size >> ED_PAGE_SHIFT);
+	sc->mem_ring = sc->mem_start + (sc->rec_page_start << ED_PAGE_SHIFT);
+	sc->mem_end = sc->mem_start + sc->mem_size;
+
+	/* Now zero memory and verify that it is clear. */
+	if ((*sc->test_mem)(sc))
+		goto out;
+
+	/* Set interface to stopped condition (reset). */
+	dp8390_stop(sc);
+
+	/* Initialize ifnet structure. */
+	bcopy(sc->sc_dev.dv_xname, ifp->if_xname, IFNAMSIZ);
+	ifp->if_softc = sc;
+	ifp->if_start = dp8390_start;
+	ifp->if_ioctl = dp8390_ioctl;
+	if (!ifp->if_watchdog)
+		ifp->if_watchdog = dp8390_watchdog;
+	ifp->if_flags =
+	    IFF_BROADCAST | IFF_SIMPLEX | IFF_NOTRAILERS | IFF_MULTICAST;
+
+	/* Initialize media goo. */
+	ifmedia_init(&sc->sc_media, 0, dp8390_mediachange, dp8390_mediastatus);
+	if (media != NULL) {
+		for (i = 0; i < nmedia; i++)
+			ifmedia_add(&sc->sc_media, media[i], 0, NULL);
+		ifmedia_set(&sc->sc_media, defmedia);
+	} else {
+		ifmedia_add(&sc->sc_media, IFM_ETHER|IFM_MANUAL, 0, NULL);
+		ifmedia_set(&sc->sc_media, IFM_ETHER|IFM_MANUAL);
+	}
+
+	/* Attach the interface. */
+	if_attach(ifp);
+#ifdef __NetBSD__
+	ether_ifattach(ifp, sc->sc_enaddr);
+#else
+	ether_ifattach(ifp);
+#endif
+#if NBPFILTER > 0
+#ifdef __NetBSD__
+	bpfattach(&ifp->if_bpf, ifp, DLT_EN10MB, sizeof(struct ether_header));
+#else
+	bpfattach(&sc->sc_arpcom.ac_if.if_bpf, ifp, DLT_EN10MB,
+		sizeof(struct ether_header));
+#endif
+#endif
+
+	/* Print additional info when attached. */
+	printf("%s: Ethernet address %s\n", sc->sc_dev.dv_xname,
+#ifdef __NetBSD__
+	    ether_sprintf(sc->sc_enaddr));
+#else
+	    ether_sprintf(sc->sc_arpcom.ac_enaddr));
+#endif
+
+	rv = 0;
+out:
+	return (rv);
+}
+
+/*
+ * Media change callback.
+ */
+int
+dp8390_mediachange(ifp)
+	struct ifnet *ifp;
+{
+	struct dp8390_softc *sc = ifp->if_softc;
+
+	if (sc->sc_mediachange)
+		return ((*sc->sc_mediachange)(sc));
+	return (EINVAL);
+}
+
+/*
+ * Media status callback.
+ */
+void
+dp8390_mediastatus(ifp, ifmr)
+	struct ifnet *ifp;
+	struct ifmediareq *ifmr;
+{
+	struct dp8390_softc *sc = ifp->if_softc;
+
+	if (sc->sc_enabled == 0) {
+		ifmr->ifm_active = IFM_ETHER | IFM_NONE;
+		ifmr->ifm_status = 0;
+		return;
+	}
+
+	if (sc->sc_mediastatus)
+		(*sc->sc_mediastatus)(sc, ifmr);
+}
+
+/*
+ * Reset interface.
+ */
+void
+dp8390_reset(sc)
+	struct dp8390_softc *sc;
+{
+	int     s;
+
+	s = splnet();
+	dp8390_stop(sc);
+	dp8390_init(sc);
+	splx(s);
+}
+
+/*
+ * Take interface offline.
+ */
+void
+dp8390_stop(sc)
+	struct dp8390_softc *sc;
+{
+	bus_space_tag_t regt = sc->sc_regt;
+	bus_space_handle_t regh = sc->sc_regh;
+	int n = 5000;
+
+	/* Stop everything on the interface, and select page 0 registers. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP);
+
+	/*
+	 * Wait for interface to enter stopped state, but limit # of checks to
+	 * 'n' (about 5ms).  It shouldn't even take 5us on modern DS8390's, but
+	 * just in case it's an old one.
+	 */
+	while (((NIC_GET(regt, regh,
+	    ED_P0_ISR) & ED_ISR_RST) == 0) && --n)
+		;
+}
+
+/*
+ * Device timeout/watchdog routine.  Entered if the device neglects to generate
+ * an interrupt after a transmit has been started on it.
+ */
+
+void
+dp8390_watchdog(ifp)
+	struct ifnet *ifp;
+{
+	struct dp8390_softc *sc = ifp->if_softc;
+
+	log(LOG_ERR, "%s: device timeout\n", sc->sc_dev.dv_xname);
+#ifdef __NetBSD__
+	++sc->sc_ec.ec_if.if_oerrors;
+#else
+	++sc->sc_arpcom.ac_if.if_oerrors;
+#endif
+
+	dp8390_reset(sc);
+}
+
+/*
+ * Initialize device.
+ */
+void
+dp8390_init(sc)
+	struct dp8390_softc *sc;
+{
+	bus_space_tag_t regt = sc->sc_regt;
+	bus_space_handle_t regh = sc->sc_regh;
+#ifdef __NetBSD__
+	struct ifnet *ifp = &sc->sc_ec.ec_if;
+#else
+	struct ifnet *ifp = &sc->sc_arpcom.ac_if;
+#endif
+	u_int8_t mcaf[8];
+	int i;
+
+	/*
+	 * Initialize the NIC in the exact order outlined in the NS manual.
+	 * This init procedure is "mandatory"...don't change what or when
+	 * things happen.
+	 */
+
+	/* Reset transmitter flags. */
+	ifp->if_timer = 0;
+
+	sc->txb_inuse = 0;
+	sc->txb_new = 0;
+	sc->txb_next_tx = 0;
+
+	/* Set interface for page 0, remote DMA complete, stopped. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP);
+
+	if (sc->dcr_reg & ED_DCR_LS) {
+		NIC_PUT(regt, regh, ED_P0_DCR, sc->dcr_reg);
+	} else {
+		/*
+		 * Set FIFO threshold to 8, No auto-init Remote DMA, byte
+		 * order=80x86, byte-wide DMA xfers,
+		 */
+		NIC_PUT(regt, regh, ED_P0_DCR, ED_DCR_FT1 | ED_DCR_LS);
+	}
+
+	/* Clear remote byte count registers. */
+	NIC_PUT(regt, regh, ED_P0_RBCR0, 0);
+	NIC_PUT(regt, regh, ED_P0_RBCR1, 0);
+
+	/* Tell RCR to do nothing for now. */
+	NIC_PUT(regt, regh, ED_P0_RCR, ED_RCR_MON);
+
+	/* Place NIC in internal loopback mode. */
+	NIC_PUT(regt, regh, ED_P0_TCR, ED_TCR_LB0);
+
+	/* Set lower bits of byte addressable framing to 0. */
+	if (sc->is790)
+		NIC_PUT(regt, regh, 0x09, 0);
+
+	/* Initialize receive buffer ring. */
+	NIC_PUT(regt, regh, ED_P0_BNRY, sc->rec_page_start);
+	NIC_PUT(regt, regh, ED_P0_PSTART, sc->rec_page_start);
+	NIC_PUT(regt, regh, ED_P0_PSTOP, sc->rec_page_stop);
+
+	/*
+	 * Clear all interrupts.  A '1' in each bit position clears the
+	 * corresponding flag.
+	 */
+	NIC_PUT(regt, regh, ED_P0_ISR, 0xff);
+
+	/*
+	 * Enable the following interrupts: receive/transmit complete,
+	 * receive/transmit error, and Receiver OverWrite.
+	 *
+	 * Counter overflow and Remote DMA complete are *not* enabled.
+	 */
+	NIC_PUT(regt, regh, ED_P0_IMR,
+	    ED_IMR_PRXE | ED_IMR_PTXE | ED_IMR_RXEE | ED_IMR_TXEE |
+	    ED_IMR_OVWE);
+
+	/* Program command register for page 1. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STP);
+
+	/* Copy out our station address. */
+	for (i = 0; i < ETHER_ADDR_LEN; ++i)
+#ifdef __NetBSD__
+		NIC_PUT(regt, regh, ED_P1_PAR0 + i,
+		    LLADDR(ifp->if_sadl)[i]);
+#else
+		NIC_PUT(regt, regh, ED_P1_PAR0 + i,
+		    sc->sc_arpcom.ac_enaddr[i]);
+#endif
+
+	/* Set multicast filter on chip. */
+#ifdef __NetBSD__
+	dp8390_getmcaf(&sc->sc_ec, mcaf);
+#else
+	dp8390_getmcaf(&sc->sc_arpcom, mcaf);
+#endif
+	for (i = 0; i < 8; i++)
+		NIC_PUT(regt, regh, ED_P1_MAR0 + i, mcaf[i]);
+
+	/*
+	 * Set current page pointer to one page after the boundary pointer, as
+	 * recommended in the National manual.
+	 */
+	sc->next_packet = sc->rec_page_start + 1;
+	NIC_PUT(regt, regh, ED_P1_CURR, sc->next_packet);
+
+	/* Program command register for page 0. */
+	NIC_PUT(regt, regh, ED_P1_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP);
+
+	i = ED_RCR_AB | ED_RCR_AM;
+	if (ifp->if_flags & IFF_PROMISC) {
+		/*
+		 * Set promiscuous mode.  Multicast filter was set earlier so
+		 * that we should receive all multicast packets.
+		 */
+		i |= ED_RCR_PRO | ED_RCR_AR | ED_RCR_SEP;
+	}
+	NIC_PUT(regt, regh, ED_P0_RCR, i);
+
+	/* Take interface out of loopback. */
+	NIC_PUT(regt, regh, ED_P0_TCR, 0);
+
+	/* Do any card-specific initialization, if applicable. */
+	if (sc->init_card)
+		(*sc->init_card)(sc);
+
+	/* Fire up the interface. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA);
+
+	/* Set 'running' flag, and clear output active flag. */
+	ifp->if_flags |= IFF_RUNNING;
+	ifp->if_flags &= ~IFF_OACTIVE;
+
+	/* ...and attempt to start output. */
+	dp8390_start(ifp);
+}
+
+/*
+ * This routine actually starts the transmission on the interface.
+ */
+static __inline__ void
+dp8390_xmit(sc)
+	struct dp8390_softc *sc;
+{
+	bus_space_tag_t regt = sc->sc_regt;
+	bus_space_handle_t regh = sc->sc_regh;
+#ifdef __NetBSD__
+	struct ifnet *ifp = &sc->sc_ec.ec_if;
+#else
+	struct ifnet *ifp = &sc->sc_arpcom.ac_if;
+#endif
+	u_short len;
+
+	len = sc->txb_len[sc->txb_next_tx];
+
+	/* Set NIC for page 0 register access. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA);
+
+	/* Set TX buffer start page. */
+	NIC_PUT(regt, regh, ED_P0_TPSR, sc->tx_page_start +
+	    sc->txb_next_tx * ED_TXBUF_SIZE);
+
+	/* Set TX length. */
+	NIC_PUT(regt, regh, ED_P0_TBCR0, len);
+	NIC_PUT(regt, regh, ED_P0_TBCR1, len >> 8);
+
+	/* Set page 0, remote DMA complete, transmit packet, and *start*. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_TXP | ED_CR_STA);
+
+	/* Point to next transmit buffer slot and wrap if necessary. */
+	sc->txb_next_tx++;
+	if (sc->txb_next_tx == sc->txb_cnt)
+		sc->txb_next_tx = 0;
+
+	/* Set a timer just in case we never hear from the board again. */
+	ifp->if_timer = 2;
+}
+
+/*
+ * Start output on interface.
+ * We make two assumptions here:
+ *  1) that the current priority is set to splnet _before_ this code
+ *     is called *and* is returned to the appropriate priority after
+ *     return
+ *  2) that the IFF_OACTIVE flag is checked before this code is called
+ *     (i.e. that the output part of the interface is idle)
+ */
+void
+dp8390_start(ifp)
+	struct ifnet *ifp;
+{
+	struct dp8390_softc *sc = ifp->if_softc;
+	struct mbuf *m0;
+	int buffer;
+	int len;
+
+	if ((ifp->if_flags & (IFF_RUNNING | IFF_OACTIVE)) != IFF_RUNNING)
+		return;
+
+outloop:
+	/* See if there is room to put another packet in the buffer. */
+	if (sc->txb_inuse == sc->txb_cnt) {
+		/* No room.  Indicate this to the outside world and exit. */
+		ifp->if_flags |= IFF_OACTIVE;
+		return;
+	}
+	IF_DEQUEUE(&ifp->if_snd, m0);
+	if (m0 == 0)
+		return;
+
+	/* We need to use m->m_pkthdr.len, so require the header */
+	if ((m0->m_flags & M_PKTHDR) == 0)
+		panic("dp8390_start: no header mbuf");
+
+#if NBPFILTER > 0
+	/* Tap off here if there is a BPF listener. */
+	if (ifp->if_bpf)
+		bpf_mtap(ifp->if_bpf, m0);
+#endif
+
+	/* txb_new points to next open buffer slot. */
+	buffer = sc->mem_start +
+	    ((sc->txb_new * ED_TXBUF_SIZE) << ED_PAGE_SHIFT);
+
+	if (sc->write_mbuf)
+		len = (*sc->write_mbuf)(sc, m0, buffer);
+	else
+		len = dp8390_write_mbuf(sc, m0, buffer);
+
+	m_freem(m0);
+	sc->txb_len[sc->txb_new] = max(len, ETHER_MIN_LEN);
+
+	/* Start the first packet transmitting. */
+	if (sc->txb_inuse == 0)
+		dp8390_xmit(sc);
+
+	/* Point to next buffer slot and wrap if necessary. */
+	if (++sc->txb_new == sc->txb_cnt)
+		sc->txb_new = 0;
+
+	sc->txb_inuse++;
+
+	/* Loop back to the top to possibly buffer more packets. */
+	goto outloop;
+}
+
+/*
+ * Ethernet interface receiver interrupt.
+ */
+void
+dp8390_rint(sc)
+	struct dp8390_softc *sc;
+{
+	bus_space_tag_t regt = sc->sc_regt;
+	bus_space_handle_t regh = sc->sc_regh;
+	struct dp8390_ring packet_hdr;
+	int packet_ptr;
+	u_short len;
+	u_char boundary, current;
+	u_char nlen;
+
+loop:
+	/* Set NIC to page 1 registers to get 'current' pointer. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STA);
+
+	/*
+	 * 'sc->next_packet' is the logical beginning of the ring-buffer - i.e.
+	 * it points to where new data has been buffered.  The 'CURR' (current)
+	 * register points to the logical end of the ring-buffer - i.e. it
+	 * points to where additional new data will be added.  We loop here
+	 * until the logical beginning equals the logical end (or in other
+	 * words, until the ring-buffer is empty).
+	 */
+	current = NIC_GET(regt, regh, ED_P1_CURR);
+	if (sc->next_packet == current)
+		return;
+
+	/* Set NIC to page 0 registers to update boundary register. */
+	NIC_PUT(regt, regh, ED_P1_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA);
+
+	do {
+		/* Get pointer to this buffer's header structure. */
+		packet_ptr = sc->mem_ring +
+		    ((sc->next_packet - sc->rec_page_start) << ED_PAGE_SHIFT);
+
+		if (sc->read_hdr)
+			(*sc->read_hdr)(sc, packet_ptr, &packet_hdr);
+		else
+			dp8390_read_hdr(sc, packet_ptr, &packet_hdr);
+		len = packet_hdr.count;
+
+		/*
+		 * Try do deal with old, buggy chips that sometimes duplicate
+		 * the low byte of the length into the high byte.  We do this
+		 * by simply ignoring the high byte of the length and always
+		 * recalculating it.
+		 *
+		 * NOTE: sc->next_packet is pointing at the current packet.
+		 */
+		if (packet_hdr.next_packet >= sc->next_packet)
+			nlen = (packet_hdr.next_packet - sc->next_packet);
+		else
+			nlen = ((packet_hdr.next_packet - sc->rec_page_start) +
+			    (sc->rec_page_stop - sc->next_packet));
+		--nlen;
+		if ((len & ED_PAGE_MASK) + sizeof(packet_hdr) > ED_PAGE_SIZE)
+			--nlen;
+		len = (len & ED_PAGE_MASK) | (nlen << ED_PAGE_SHIFT);
+#ifdef DIAGNOSTIC
+		if (len != packet_hdr.count) {
+			printf("%s: length does not match "
+			    "next packet pointer\n", sc->sc_dev.dv_xname);
+			printf("%s: len %04x nlen %04x start %02x "
+			    "first %02x curr %02x next %02x stop %02x\n",
+			    sc->sc_dev.dv_xname, packet_hdr.count, len,
+			    sc->rec_page_start, sc->next_packet, current,
+			    packet_hdr.next_packet, sc->rec_page_stop);
+		}
+#endif
+
+		/*
+		 * Be fairly liberal about what we allow as a "reasonable"
+		 * length so that a [crufty] packet will make it to BPF (and
+		 * can thus be analyzed).  Note that all that is really
+		 * important is that we have a length that will fit into one
+		 * mbuf cluster or less; the upper layer protocols can then
+		 * figure out the length from their own length field(s).
+		 */
+		if (len <= MCLBYTES &&
+		    packet_hdr.next_packet >= sc->rec_page_start &&
+		    packet_hdr.next_packet < sc->rec_page_stop) {
+			/* Go get packet. */
+			dp8390_read(sc,
+			    packet_ptr + sizeof(struct dp8390_ring),
+			    len - sizeof(struct dp8390_ring));
+#ifdef __NetBSD__
+			++sc->sc_ec.ec_if.if_ipackets;
+#else
+			++sc->sc_arpcom.ac_if.if_ipackets;
+#endif
+		} else {
+			/* Really BAD.  The ring pointers are corrupted. */
+			log(LOG_ERR, "%s: NIC memory corrupt - "
+			    "invalid packet length %d\n",
+			    sc->sc_dev.dv_xname, len);
+#ifdef __NetBSD__
+			++sc->sc_ec.ec_if.if_ierrors;
+#else
+			++sc->sc_arpcom.ac_if.if_ierrors;
+#endif
+			dp8390_reset(sc);
+			return;
+		}
+
+		/* Update next packet pointer. */
+		sc->next_packet = packet_hdr.next_packet;
+
+		/*
+		 * Update NIC boundary pointer - being careful to keep it one
+		 * buffer behind (as recommended by NS databook).
+		 */
+		boundary = sc->next_packet - 1;
+		if (boundary < sc->rec_page_start)
+			boundary = sc->rec_page_stop - 1;
+		NIC_PUT(regt, regh, ED_P0_BNRY, boundary);
+	} while (sc->next_packet != current);
+
+	goto loop;
+}
+
+/* Ethernet interface interrupt processor. */
+int
+dp8390_intr(arg)
+	void *arg;
+{
+	struct dp8390_softc *sc = (struct dp8390_softc *)arg;
+	bus_space_tag_t regt = sc->sc_regt;
+	bus_space_handle_t regh = sc->sc_regh;
+#ifdef __NetBSD__
+	struct ifnet *ifp = &sc->sc_ec.ec_if;
+#else
+	struct ifnet *ifp = &sc->sc_arpcom.ac_if;
+#endif
+	u_char isr;
+
+	if (sc->sc_enabled == 0)
+		return (0);
+
+	/* Set NIC to page 0 registers. */
+	NIC_PUT(regt, regh, ED_P0_CR,
+	    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA);
+
+	isr = NIC_GET(regt, regh, ED_P0_ISR);
+	if (!isr)
+		return (0);
+
+	/* Loop until there are no more new interrupts. */
+	for (;;) {
+		/*
+		 * Reset all the bits that we are 'acknowledging' by writing a
+		 * '1' to each bit position that was set.
+		 * (Writing a '1' *clears* the bit.)
+		 */
+		NIC_PUT(regt, regh, ED_P0_ISR, isr);
+
+		/*
+		 * Handle transmitter interrupts.  Handle these first because
+		 * the receiver will reset the board under some conditions.
+		 */
+		if (isr & (ED_ISR_PTX | ED_ISR_TXE)) {
+			u_char collisions = NIC_GET(regt, regh,
+			    ED_P0_NCR) & 0x0f;
+
+			/*
+			 * Check for transmit error.  If a TX completed with an
+			 * error, we end up throwing the packet away.  Really
+			 * the only error that is possible is excessive
+			 * collisions, and in this case it is best to allow the
+			 * automatic mechanisms of TCP to backoff the flow.  Of
+			 * course, with UDP we're screwed, but this is expected
+			 * when a network is heavily loaded.
+			 */
+			(void)NIC_GET(regt, regh, ED_P0_TSR);
+			if (isr & ED_ISR_TXE) {
+				/*
+				 * Excessive collisions (16).
+				 */
+				if ((NIC_GET(regt, regh, ED_P0_TSR)
+				    & ED_TSR_ABT) && (collisions == 0)) {
+					/*
+					 * When collisions total 16, the P0_NCR
+					 * will indicate 0, and the TSR_ABT is
+					 * set.
+					 */
+					collisions = 16;
+				}
+
+				/* Update output errors counter. */
+				++ifp->if_oerrors;
+			} else {
+				/*
+				 * Update total number of successfully
+				 * transmitted packets.
+				 */
+				++ifp->if_opackets;
+			}
+
+			/* Done with the buffer. */
+			sc->txb_inuse--;
+
+			/* Clear watchdog timer. */
+			ifp->if_timer = 0;
+			ifp->if_flags &= ~IFF_OACTIVE;
+
+			/*
+			 * Add in total number of collisions on last
+			 * transmission.
+			 */
+			ifp->if_collisions += collisions;
+
+			/*
+			 * Decrement buffer in-use count if not zero (can only
+			 * be zero if a transmitter interrupt occured while not
+			 * actually transmitting).
+			 * If data is ready to transmit, start it transmitting,
+			 * otherwise defer until after handling receiver.
+			 */
+			if (sc->txb_inuse > 0)
+				dp8390_xmit(sc);
+		}
+
+		/* Handle receiver interrupts. */
+		if (isr & (ED_ISR_PRX | ED_ISR_RXE | ED_ISR_OVW)) {
+			/*
+			 * Overwrite warning.  In order to make sure that a
+			 * lockup of the local DMA hasn't occurred, we reset
+			 * and re-init the NIC.  The NSC manual suggests only a
+			 * partial reset/re-init is necessary - but some chips
+			 * seem to want more.  The DMA lockup has been seen
+			 * only with early rev chips - Methinks this bug was
+			 * fixed in later revs.  -DG
+			 */
+			if (isr & ED_ISR_OVW) {
+				++ifp->if_ierrors;
+#ifdef DIAGNOSTIC
+				log(LOG_WARNING, "%s: warning - receiver "
+				    "ring buffer overrun\n",
+				    sc->sc_dev.dv_xname);
+#endif
+				/* Stop/reset/re-init NIC. */
+				dp8390_reset(sc);
+			} else {
+				/*
+				 * Receiver Error.  One or more of: CRC error,
+				 * frame alignment error FIFO overrun, or
+				 * missed packet.
+				 */
+				if (isr & ED_ISR_RXE) {
+					++ifp->if_ierrors;
+#ifdef DEBUG
+					if (dp8390_debug) {
+						printf("%s: receive error %x\n",
+						    sc->sc_dev.dv_xname,
+						    NIC_GET(regt, regh,
+							ED_P0_RSR));
+					}
+#endif
+				}
+
+				/*
+				 * Go get the packet(s)
+				 * XXX - Doing this on an error is dubious
+				 * because there shouldn't be any data to get
+				 * (we've configured the interface to not
+				 * accept packets with errors).
+				 */
+				if (sc->recv_int)
+					(*sc->recv_int)(sc);
+				else
+					dp8390_rint(sc);
+			}
+		}
+
+		/*
+		 * If it looks like the transmitter can take more data, attempt
+		 * to start output on the interface.  This is done after
+		 * handling the receiver to give the receiver priority.
+		 */
+		dp8390_start(ifp);
+
+		/*
+		 * Return NIC CR to standard state: page 0, remote DMA
+		 * complete, start (toggling the TXP bit off, even if was just
+		 * set in the transmit routine, is *okay* - it is 'edge'
+		 * triggered from low to high).
+		 */
+		NIC_PUT(regt, regh, ED_P0_CR,
+		    sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA);
+
+		/*
+		 * If the Network Talley Counters overflow, read them to reset
+		 * them.  It appears that old 8390's won't clear the ISR flag
+		 * otherwise - resulting in an infinite loop.
+		 */
+		if (isr & ED_ISR_CNT) {
+			(void)NIC_GET(regt, regh, ED_P0_CNTR0);
+			(void)NIC_GET(regt, regh, ED_P0_CNTR1);
+			(void)NIC_GET(regt, regh, ED_P0_CNTR2);
+		}
+
+		isr = NIC_GET(regt, regh, ED_P0_ISR);
+		if (!isr)
+			return (1);
+	}
+}
+
+/*
+ * Process an ioctl request.  This code needs some work - it looks pretty ugly.
+ */
+int
+dp8390_ioctl(ifp, cmd, data)
+	struct ifnet *ifp;
+	u_long cmd;
+	caddr_t data;
+{
+	struct dp8390_softc *sc = ifp->if_softc;
+	struct ifaddr *ifa = (struct ifaddr *) data;
+	struct ifreq *ifr = (struct ifreq *) data;
+	int s, error = 0;
+
+	s = splnet();
+
+	switch (cmd) {
+
+	case SIOCSIFADDR:
+		if ((error = dp8390_enable(sc)) != 0)
+			break;
+		ifp->if_flags |= IFF_UP;
+
+		switch (ifa->ifa_addr->sa_family) {
+#ifdef INET
+		case AF_INET:
+			dp8390_init(sc);
+#ifdef __NetBSD__
+			arp_ifinit(ifp, ifa);
+#else
+			arp_ifinit(&sc->sc_arpcom, ifa);
+#endif
+			break;
+#endif
+#ifdef NS
+			/* XXX - This code is probably wrong. */
+		case AF_NS:
+		    {
+			struct ns_addr *ina = &IA_SNS(ifa)->sns_addr;
+
+			if (ns_nullhost(*ina))
+				ina->x_host =
+				    *(union ns_host *)LLADDR(ifp->if_sadl);
+			else
+				bcopy(ina->x_host.c_host, LLADDR(ifp->if_sadl),
+				    ETHER_ADDR_LEN);
+			/* Set new address. */
+			dp8390_init(sc);
+			break;
+		    }
+#endif
+		default:
+			dp8390_init(sc);
+			break;
+		}
+		break;
+
+	case SIOCSIFFLAGS:
+		if ((ifp->if_flags & IFF_UP) == 0 &&
+		    (ifp->if_flags & IFF_RUNNING) != 0) {
+			/*
+			 * If interface is marked down and it is running, then
+			 * stop it.
+			 */
+			dp8390_stop(sc);
+			ifp->if_flags &= ~IFF_RUNNING;
+			dp8390_disable(sc);
+		} else if ((ifp->if_flags & IFF_UP) != 0 &&
+		    (ifp->if_flags & IFF_RUNNING) == 0) {
+			/*
+			 * If interface is marked up and it is stopped, then
+			 * start it.
+			 */
+			if ((error = dp8390_enable(sc)) != 0)
+				break;
+			dp8390_init(sc);
+		} else if (sc->sc_enabled) {
+			/*
+			 * Reset the interface to pick up changes in any other
+			 * flags that affect hardware registers.
+			 */
+			dp8390_stop(sc);
+			dp8390_init(sc);
+		}
+		break;
+
+	case SIOCADDMULTI:
+	case SIOCDELMULTI:
+		if (sc->sc_enabled == 0) {
+			error = EIO;
+			break;
+		}
+
+		/* Update our multicast list. */
+		error = (cmd == SIOCADDMULTI) ?
+#ifdef __NetBSD__
+		    ether_addmulti(ifr, &sc->sc_ec) :
+		    ether_delmulti(ifr, &sc->sc_ec);
+#else
+		    ether_addmulti(ifr, &sc->sc_arpcom) :
+		    ether_delmulti(ifr, &sc->sc_arpcom);
+#endif
+
+		if (error == ENETRESET) {
+			/*
+			 * Multicast list has changed; set the hardware filter
+			 * accordingly.
+			 */
+			dp8390_stop(sc);	/* XXX for ds_setmcaf? */
+			dp8390_init(sc);
+			error = 0;
+		}
+		break;
+
+	case SIOCGIFMEDIA:
+	case SIOCSIFMEDIA:
+		error = ifmedia_ioctl(ifp, ifr, &sc->sc_media, cmd);
+		break;
+
+	default:
+		error = EINVAL;
+		break;
+	}
+
+	splx(s);
+	return (error);
+}
+
+/*
+ * Retrieve packet from buffer memory and send to the next level up via
+ * ether_input().  If there is a BPF listener, give a copy to BPF, too.
+ */
+void
+dp8390_read(sc, buf, len)
+	struct dp8390_softc *sc;
+	int buf;
+	u_short len;
+{
+#ifdef __NetBSD__
+	struct ifnet *ifp = &sc->sc_ec.ec_if;
+#else
+	struct ifnet *ifp = &sc->sc_arpcom.ac_if;
+#endif
+	struct mbuf *m;
+	struct ether_header *eh;
+
+	/* Pull packet off interface. */
+	m = dp8390_get(sc, buf, len);
+	if (m == 0) {
+		ifp->if_ierrors++;
+		return;
+	}
+
+	ifp->if_ipackets++;
+
+	/* We assume that the header fits entirely in one mbuf. */
+	eh = mtod(m, struct ether_header *);
+
+#if NBPFILTER > 0
+	/*
+	 * Check if there's a BPF listener on this interface.
+	 * If so, hand off the raw packet to bpf.
+	 */
+	if (ifp->if_bpf) {
+		bpf_mtap(ifp->if_bpf, m);
+
+		/*
+		 * Note that the interface cannot be in promiscuous mode if
+		 * there are no BPF listeners.  And if we are in promiscuous
+		 * mode, we have to check if this packet is really ours.
+		 */
+		if ((ifp->if_flags & IFF_PROMISC) &&
+		    (eh->ether_dhost[0] & 1) == 0 &&	/* !mcast and !bcast */
+#ifdef __NetBSD__
+		    bcmp(eh->ether_dhost, LLADDR(ifp->if_sadl),
+#else
+		    bcmp(eh->ether_dhost, sc->sc_arpcom.ac_enaddr,
+#endif
+		    sizeof(eh->ether_dhost)) != 0) {
+			m_freem(m);
+			return;
+		}
+	}
+#endif
+
+	/* Fix up data start offset in mbuf to point past ether header. */
+	m_adj(m, sizeof(struct ether_header));
+	ether_input(ifp, eh, m);
+}
+
+
+/*
+ * Supporting routines.
+ */
+
+/*
+ * Compute the multicast address filter from the list of multicast addresses we
+ * need to listen to.
+ */
+void
+dp8390_getmcaf(ec, af)
+#ifdef __NetBSD__
+	struct ethercom *ec;
+#else
+	struct arpcom *ec;
+#endif
+	u_int8_t *af;
+{
+#ifdef __NetBSD__
+	struct ifnet *ifp = &ec->ec_if;
+#else
+	struct ifnet *ifp = &ec->ac_if;
+#endif
+	struct ether_multi *enm;
+	u_int8_t *cp, c;
+	u_int32_t crc;
+	int i, len;
+	struct ether_multistep step;
+
+	/*
+	 * Set up multicast address filter by passing all multicast addresses
+	 * through a crc generator, and then using the high order 6 bits as an
+	 * index into the 64 bit logical address filter.  The high order bit
+	 * selects the word, while the rest of the bits select the bit within
+	 * the word.
+	 */
+
+	if (ifp->if_flags & IFF_PROMISC) {
+		ifp->if_flags |= IFF_ALLMULTI;
+		for (i = 0; i < 8; i++)
+			af[i] = 0xff;
+		return;
+	}
+	for (i = 0; i < 8; i++)
+		af[i] = 0;
+	ETHER_FIRST_MULTI(step, ec, enm);
+	while (enm != NULL) {
+		if (bcmp(enm->enm_addrlo, enm->enm_addrhi,
+		    sizeof(enm->enm_addrlo)) != 0) {
+			/*
+			 * We must listen to a range of multicast addresses.
+			 * For now, just accept all multicasts, rather than
+			 * trying to set only those filter bits needed to match
+			 * the range.  (At this time, the only use of address
+			 * ranges is for IP multicast routing, for which the
+			 * range is big enough to require all bits set.)
+			 */
+			ifp->if_flags |= IFF_ALLMULTI;
+			for (i = 0; i < 8; i++)
+				af[i] = 0xff;
+			return;
+		}
+		cp = enm->enm_addrlo;
+		crc = 0xffffffff;
+		for (len = sizeof(enm->enm_addrlo); --len >= 0;) {
+			c = *cp++;
+			for (i = 8; --i >= 0;) {
+				if (((crc & 0x80000000) ? 1 : 0) ^ (c & 0x01)) {
+					crc <<= 1;
+					crc ^= 0x04c11db6 | 1;
+				} else
+					crc <<= 1;
+				c >>= 1;
+			}
+		}
+		/* Just want the 6 most significant bits. */
+		crc >>= 26;
+
+		/* Turn on the corresponding bit in the filter. */
+		af[crc >> 3] |= 1 << (crc & 0x7);
+
+		ETHER_NEXT_MULTI(step, enm);
+	}
+	ifp->if_flags &= ~IFF_ALLMULTI;
+}
+
+/*
+ * Copy data from receive buffer to end of mbuf chain allocate additional mbufs
+ * as needed.  Return pointer to last mbuf in chain.
+ * sc = dp8390 info (softc)
+ * src = pointer in dp8390 ring buffer
+ * dst = pointer to last mbuf in mbuf chain to copy to
+ * amount = amount of data to copy
+ */
+struct mbuf *
+dp8390_get(sc, src, total_len)
+	struct dp8390_softc *sc;
+	int src;
+	u_short total_len;
+{
+#ifdef __NetBSD__
+	struct ifnet *ifp = &sc->sc_ec.ec_if;
+#else
+	struct ifnet *ifp = &sc->sc_arpcom.ac_if;
+#endif
+	struct mbuf *top, **mp, *m;
+	u_short len;
+
+	MGETHDR(m, M_DONTWAIT, MT_DATA);
+	if (m == 0)
+		return 0;
+	m->m_pkthdr.rcvif = ifp;
+	m->m_pkthdr.len = total_len;
+	len = MHLEN;
+	top = 0;
+	mp = &top;
+
+	while (total_len > 0) {
+		if (top) {
+			MGET(m, M_DONTWAIT, MT_DATA);
+			if (m == 0) {
+				m_freem(top);
+				return 0;
+			}
+			len = MLEN;
+		}
+		if (total_len >= MINCLSIZE) {
+			MCLGET(m, M_DONTWAIT);
+			if ((m->m_flags & M_EXT) == 0) {
+				m_freem(m);
+				m_freem(top);
+				return 0;
+			}
+			len = MCLBYTES;
+		}
+
+		/*
+		 * Make sure the data after the Ethernet header is aligned.
+		 */
+		if (top == NULL) {
+			caddr_t newdata = (caddr_t)
+			    ALIGN(m->m_data + sizeof(struct ether_header)) -
+			    sizeof(struct ether_header);
+			len -= newdata - m->m_data;
+			m->m_data = newdata;
+		}
+
+		m->m_len = len = min(total_len, len);
+		if (sc->ring_copy)
+			src = (*sc->ring_copy)(sc, src, mtod(m, caddr_t), len);
+		else
+			src = dp8390_ring_copy(sc, src, mtod(m, caddr_t), len);
+		total_len -= len;
+		*mp = m;
+		mp = &m->m_next;
+	}
+
+	return top;
+}
+
+
+/*
+ * Default driver support functions.
+ *
+ * NOTE: all support functions assume 8-bit shared memory.
+ */
+/*
+ * Zero NIC buffer memory and verify that it is clear.
+ */
+static int
+dp8390_test_mem(sc)
+	struct dp8390_softc *sc;
+{
+	bus_space_tag_t buft = sc->sc_buft;
+	bus_space_handle_t bufh = sc->sc_bufh;
+	int i;
+
+	bus_space_set_region_1(buft, bufh, sc->mem_start, 0, sc->mem_size);
+
+	for (i = 0; i < sc->mem_size; ++i) {
+		if (bus_space_read_1(buft, bufh, sc->mem_start + i)) {
+			printf(": failed to clear NIC buffer at offset %x - "
+			    "check configuration\n", (sc->mem_start + i));
+			return 1;
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * Read a packet header from the ring, given the source offset.
+ */
+static __inline__ void
+dp8390_read_hdr(sc, src, hdrp)
+	struct dp8390_softc *sc;
+	int src;
+	struct dp8390_ring *hdrp;
+{
+	bus_space_tag_t buft = sc->sc_buft;
+	bus_space_handle_t bufh = sc->sc_bufh;
+
+	/*
+	 * The byte count includes a 4 byte header that was added by
+	 * the NIC.
+	 */
+	hdrp->rsr = bus_space_read_1(buft, bufh, src);
+	hdrp->next_packet = bus_space_read_1(buft, bufh, src + 1);
+	hdrp->count = bus_space_read_1(buft, bufh, src + 2) |
+	    (bus_space_read_1(buft, bufh, src + 3) << 8);
+}
+
+/*
+ * Copy `amount' bytes from a packet in the ring buffer to a linear
+ * destination buffer, given a source offset and destination address.
+ * Takes into account ring-wrap.
+ */
+static __inline__ int
+dp8390_ring_copy(sc, src, dst, amount)
+	struct dp8390_softc *sc;
+	int src;
+	caddr_t dst;
+	u_short amount;
+{
+	bus_space_tag_t buft = sc->sc_buft;
+	bus_space_handle_t bufh = sc->sc_bufh;
+	u_short tmp_amount;
+
+	/* Does copy wrap to lower addr in ring buffer? */
+	if (src + amount > sc->mem_end) {
+		tmp_amount = sc->mem_end - src;
+
+		/* Copy amount up to end of NIC memory. */
+		bus_space_read_region_1(buft, bufh, src, dst, tmp_amount);
+
+		amount -= tmp_amount;
+		src = sc->mem_ring;
+		dst += tmp_amount;
+	}
+	bus_space_read_region_1(buft, bufh, src, dst, amount);
+
+	return (src + amount);
+}
+
+/*
+ * Copy a packet from an mbuf to the transmit buffer on the card.
+ *
+ * Currently uses an extra buffer/extra memory copy, unless the whole
+ * packet fits in one mbuf.
+ */
+static __inline__ int
+dp8390_write_mbuf(sc, m, buf)
+	struct dp8390_softc *sc;
+	struct mbuf *m;
+	int buf;
+{
+	bus_space_tag_t buft = sc->sc_buft;
+	bus_space_handle_t bufh = sc->sc_bufh;
+	u_char *data;
+	int len, totlen = 0;
+
+	for (; m ; m = m->m_next) {
+		data = mtod(m, u_char *);
+		len = m->m_len;
+		if (len > 0) {
+			bus_space_write_region_1(buft, bufh, buf, data, len);
+			totlen += len;
+			buf += len;
+		}
+	}
+
+	return (totlen);
+}
+
+/*
+ * Enable power on the interface.
+ */
+int
+dp8390_enable(sc)
+	struct dp8390_softc *sc;
+{
+
+	if (sc->sc_enabled == 0 && sc->sc_enable != NULL) {
+		if ((*sc->sc_enable)(sc) != 0) {
+			printf("%s: device enable failed\n",
+			    sc->sc_dev.dv_xname);
+			return (EIO);
+		}
+	}
+
+	sc->sc_enabled = 1;
+	return (0);
+}
+
+/*
+ * Disable power on the interface.
+ */
+void
+dp8390_disable(sc)
+	struct dp8390_softc *sc;
+{
+
+	if (sc->sc_enabled != 0 && sc->sc_disable != NULL) {
+		(*sc->sc_disable)(sc);
+		sc->sc_enabled = 0;
+	}
+}
diff --git a/sys/dev/ic/dp8390reg.h b/sys/dev/ic/dp8390reg.h
index 71e205f6f91..5de88e44770 100644
--- a/sys/dev/ic/dp8390reg.h
+++ b/sys/dev/ic/dp8390reg.h
@@ -1,5 +1,5 @@
-/*	$OpenBSD: dp8390reg.h,v 1.4 1997/04/14 07:03:22 millert Exp $	*/
-/*	$NetBSD: dp8390reg.h,v 1.2 1995/04/12 16:12:42 mycroft Exp $	*/
+/*	$OpenBSD: dp8390reg.h,v 1.5 1998/09/22 06:41:13 fgsch Exp $	*/
+/*	$NetBSD: dp8390reg.h,v 1.3 1997/04/29 04:32:08 scottr Exp $	*/
 
 /*
  * National Semiconductor DS8390 NIC register definitions.
@@ -318,10 +318,8 @@
 #define ED_DCR_FT1	0x40
 
 /*
- * QTS: Quad-word Transfer Select.  QTS establishes 32-bit word transfers
- * for both remote and local DMA transfers.  (XXX - correct name?)
+ * bit 7 (0x80) is unused/reserved
  */
-#define ED_DCR_QTS	0x80
 
 /*
  *		Transmit Configuration Register (TCR) definitions
@@ -521,7 +519,7 @@
 #define ED_RSR_DFR	0x80
 
 /*
- * receive ring discriptor
+ * receive ring descriptor
  *
  * The National Semiconductor DS8390 Network interface controller uses the
  * following receive ring headers.  The way this works is that the memory on
@@ -530,12 +528,28 @@
  * end block #'s in the NIC.  For each packet that is put into the receive
  * ring, one of these headers (4 bytes each) is tacked onto the front.   The
  * first byte is a copy of the receiver status register at the time the packet
- * was received.  The following constants are offsets into the headers.
- */
-#define ED_RING_RSR		0	/* receiver status */
-#define ED_RING_NEXT_PACKET	1	/* pointer to next packet */
-#define ED_RING_COUNT		2	/* bytes in packet (length + 4) */
-#define ED_RING_HDRSZ		4	/* Header size */
+ * was received.
+ */
+struct dp8390_ring	{
+	u_int8_t	rsr;		/* receiver status */
+	u_int8_t	next_packet;	/* pointer to next packet */
+	u_int16_t	count;		/* bytes in packet (length + 4) */
+};
+
+/*
+ * XXX For compatibility only!  This needs to die when all drivers have
+ * been converted to be front ends to the MI driver.
+ */
+struct ed_ring	{
+#if BYTE_ORDER == BIG_ENDIAN
+	u_char	next_packet;		/* pointer to next packet */
+	u_char	rsr;			/* receiver status */
+#else
+	u_char	rsr;			/* receiver status */
+	u_char	next_packet;		/* pointer to next packet */
+#endif
+	u_short	count;			/* bytes in packet (length + 4) */
+};
 
 /*
  * Common constants
diff --git a/sys/dev/ic/dp8390var.h b/sys/dev/ic/dp8390var.h
new file mode 100644
index 00000000000..49dd6ccb701
--- /dev/null
+++ b/sys/dev/ic/dp8390var.h
@@ -0,0 +1,152 @@
+/*	$OpenBSD: dp8390var.h,v 1.1 1998/09/22 06:41:13 fgsch Exp $	*/
+/*	$NetBSD: dp8390var.h,v 1.8 1998/08/12 07:19:09 scottr Exp $	*/
+
+/*
+ * Device driver for National Semiconductor DS8390/WD83C690 based ethernet
+ * adapters.
+ *
+ * Copyright (c) 1994, 1995 Charles M. Hannum.  All rights reserved.
+ *
+ * Copyright (C) 1993, David Greenman.  This software may be used, modified,
+ * copied, distributed, and sold, in both source and binary form provided that
+ * the above copyright and these terms are retained.  Under no circumstances is
+ * the author responsible for the proper functioning of this software, nor does
+ * the author assume any responsibility for damages incurred with its use.
+ */
+
+#define INTERFACE_NAME_LEN	32
+
+/*
+ * dp8390_softc: per line info and status
+ */
+struct dp8390_softc {
+	struct device	sc_dev;
+	void	*sc_ih;
+	int	sc_flags;		/* interface flags, from config */
+
+#ifdef __NetBSD__
+	struct ethercom sc_ec;		/* ethernet common */
+#else
+	struct arpcom sc_arpcom;	/* ethernet common */
+#endif
+	struct ifmedia sc_media;	/* supported media information */
+
+	bus_space_tag_t	sc_regt;	/* NIC register space tag */
+	bus_space_handle_t sc_regh;	/* NIC register space handle */
+	bus_space_tag_t	sc_buft;	/* Buffer space tag */
+	bus_space_handle_t sc_bufh;	/* Buffer space handle */
+
+	bus_size_t sc_reg_map[16];	/* register map (offsets) */
+
+	int	is790;		/* NIC is a 790 */
+
+	u_int8_t cr_proto;	/* values always set in CR */
+	u_int8_t dcr_reg;	/* override DCR iff LS is set */
+
+	int	mem_start;	/* offset of NIC memory */
+	int	mem_end;	/* offset of NIC memory end */
+	int	mem_size;	/* total shared memory size */
+	int	mem_ring;	/* offset of start of RX ring-buffer */
+
+	u_short	txb_cnt;	/* Number of transmit buffers */
+	u_short	txb_inuse;	/* number of transmit buffers active */
+
+	u_short	txb_new;	/* pointer to where new buffer will be added */
+	u_short	txb_next_tx;	/* pointer to next buffer ready to xmit */
+	u_short	txb_len[8];	/* buffered xmit buffer lengths */
+	u_short	tx_page_start;	/* first page of TX buffer area */
+	u_short	rec_page_start; /* first page of RX ring-buffer */
+	u_short	rec_page_stop;	/* last page of RX ring-buffer */
+	u_short	next_packet;	/* pointer to next unread RX packet */
+
+#ifdef __NetBSD__
+	u_int8_t sc_enaddr[6];	/* storage for MAC address */
+#endif
+
+	int	sc_enabled;	/* boolean; power enabled on interface */
+
+	int	(*test_mem) __P((struct dp8390_softc *));
+	void	(*init_card) __P((struct dp8390_softc *));
+	void	(*read_hdr) __P((struct dp8390_softc *,
+		    int, struct dp8390_ring *));
+	void	(*recv_int) __P((struct dp8390_softc *));
+	int	(*ring_copy) __P((struct dp8390_softc *,
+		    int, caddr_t, u_short));
+	int	(*write_mbuf) __P((struct dp8390_softc *, struct mbuf *, int));
+
+	int	(*sc_enable) __P((struct dp8390_softc *));
+	void	(*sc_disable) __P((struct dp8390_softc *));
+
+	int	(*sc_mediachange) __P((struct dp8390_softc *));
+	void	(*sc_mediastatus) __P((struct dp8390_softc *,
+		    struct ifmediareq *));
+};
+
+/*
+ * Vendor types
+ */
+#define DP8390_VENDOR_UNKNOWN	0xff	/* Unknown network card */
+#define DP8390_VENDOR_WD_SMC	0x00	/* Western Digital/SMC */
+#define DP8390_VENDOR_3COM	0x01	/* 3Com */
+#define DP8390_VENDOR_NOVELL	0x02	/* Novell */
+#define DP8390_VENDOR_APPLE	0x10	/* Apple Ethernet card */
+#define DP8390_VENDOR_INTERLAN	0x11	/* Interlan A310 card (GatorCard) */
+#define DP8390_VENDOR_DAYNA	0x12	/* DaynaPORT E/30s (and others?) */
+#define DP8390_VENDOR_ASANTE	0x13	/* Asante MacCon II/E */
+#define DP8390_VENDOR_FARALLON	0x14	/* Farallon EtherMac II-TP */
+#define DP8390_VENDOR_FOCUS	0x15	/* FOCUS Enhancements EtherLAN */
+#define DP8390_VENDOR_KINETICS	0x16	/* Kinetics EtherPort SE/30 */
+#define DP8390_VENDOR_CABLETRON	0x17	/* Cabletron Ethernet */
+
+/*
+ * Compile-time config flags
+ */
+/*
+ * This sets the default for enabling/disablng the tranceiver.
+ */
+#define DP8390_DISABLE_TRANCEIVER	0x0001
+
+/*
+ * This forces the board to be used in 8/16-bit mode even if it autoconfigs
+ * differently.
+ */
+#define DP8390_FORCE_8BIT_MODE		0x0002
+#define DP8390_FORCE_16BIT_MODE		0x0004
+
+/*
+ * This disables the use of multiple transmit buffers.
+ */
+#define DP8390_NO_MULTI_BUFFERING	0x0008
+
+/*
+ * This forces all operations with the NIC memory to use Programmed I/O (i.e.
+ * not via shared memory).
+ */
+#define DP8390_FORCE_PIO		0x0010
+
+/*
+ * NIC register access macros
+ */
+#define NIC_GET(t, h, reg)	bus_space_read_1(t, h,			\
+				    ((sc)->sc_reg_map[reg]))
+#define NIC_PUT(t, h, reg, val)	bus_space_write_1(t, h,			\
+				    ((sc)->sc_reg_map[reg]), (val))
+
+int	dp8390_config __P((struct dp8390_softc *, int *, int, int));
+int	dp8390_intr __P((void *));
+int	dp8390_ioctl __P((struct ifnet *, u_long, caddr_t));
+void	dp8390_start __P((struct ifnet *));
+void	dp8390_watchdog __P((struct ifnet *));
+void	dp8390_reset __P((struct dp8390_softc *));
+void	dp8390_init __P((struct dp8390_softc *));
+void	dp8390_stop __P((struct dp8390_softc *));
+
+void	dp8390_rint __P((struct dp8390_softc *));
+
+#ifdef __NetBSD__
+void	dp8390_getmcaf __P((struct ethercom *, u_int8_t *));
+#else
+void	dp8390_getmcaf __P((struct arpcom *, u_int8_t *));
+#endif
+struct mbuf *dp8390_get __P((struct dp8390_softc *, int, u_short));
+void	dp8390_read __P((struct dp8390_softc *, int, u_short));