Oops.. missed these files out of the radeon git update.

>Update the radeondrm driver to be level with drm git.
>
>adds:
>
>- support for RS400 chips
>- some cleanup of a few things
>- fixes a hard lockup for r3-500 cards.
>
>Tested by a few

2 files changed, 286 insertions, 78 deletions

diff --git a/sys/dev/pci/drm/r300_cmdbuf.c b/sys/dev/pci/drm/r300_cmdbuf.c
index bff6378fb27..254c0691faf 100644
--- a/sys/dev/pci/drm/r300_cmdbuf.c
+++ b/sys/dev/pci/drm/r300_cmdbuf.c
@@ -136,6 +136,18 @@ static int r300_emit_cliprects(drm_radeon_private_t *dev_priv,
 		ADVANCE_RING();
 	}
 
+	/* flus cache and wait idle clean after cliprect change */
+	BEGIN_RING(2);
+	OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0));
+	OUT_RING(R300_RB3D_DC_FLUSH);
+	ADVANCE_RING();
+	BEGIN_RING(2);
+	OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0));
+	OUT_RING(RADEON_WAIT_3D_IDLECLEAN);
+	ADVANCE_RING();
+	/* set flush flag */
+	dev_priv->track_flush |= RADEON_FLUSH_EMITED;
+
 	return 0;
 }
 
@@ -166,13 +178,13 @@ void r300_init_reg_flags(struct drm_device *dev)
 	ADD_RANGE(0x21DC, 1);
 	ADD_RANGE(R300_VAP_UNKNOWN_221C, 1);
 	ADD_RANGE(R300_VAP_CLIP_X_0, 4);
-	ADD_RANGE(R300_VAP_PVS_WAITIDLE, 1);
+	ADD_RANGE(R300_VAP_PVS_STATE_FLUSH_REG, 1);
 	ADD_RANGE(R300_VAP_UNKNOWN_2288, 1);
 	ADD_RANGE(R300_VAP_OUTPUT_VTX_FMT_0, 2);
 	ADD_RANGE(R300_VAP_PVS_CNTL_1, 3);
 	ADD_RANGE(R300_GB_ENABLE, 1);
 	ADD_RANGE(R300_GB_MSPOS0, 5);
-	ADD_RANGE(R300_TX_CNTL, 1);
+	ADD_RANGE(R300_TX_INVALTAGS, 1);
 	ADD_RANGE(R300_TX_ENABLE, 1);
 	ADD_RANGE(0x4200, 4);
 	ADD_RANGE(0x4214, 1);
@@ -190,7 +202,7 @@ void r300_init_reg_flags(struct drm_device *dev)
 	ADD_RANGE(0x42C0, 2);
 	ADD_RANGE(R300_RS_CNTL_0, 2);
 
-	ADD_RANGE(0x43A4, 2);
+	ADD_RANGE(R300_SC_HYPERZ, 2);
 	ADD_RANGE(0x43E8, 1);
 
 	ADD_RANGE(0x46A4, 5);
@@ -209,14 +221,12 @@ void r300_init_reg_flags(struct drm_device *dev)
 	ADD_RANGE(0x4E50, 9);
 	ADD_RANGE(0x4E88, 1);
 	ADD_RANGE(0x4EA0, 2);
-	ADD_RANGE(R300_RB3D_ZSTENCIL_CNTL_0, 3);
-	ADD_RANGE(R300_RB3D_ZSTENCIL_FORMAT, 4);
-	ADD_RANGE_MARK(R300_RB3D_DEPTHOFFSET, 1, MARK_CHECK_OFFSET);	/* check offset */
-	ADD_RANGE(R300_RB3D_DEPTHPITCH, 1);
-	ADD_RANGE(0x4F28, 1);
-	ADD_RANGE(0x4F30, 2);
-	ADD_RANGE(0x4F44, 1);
-	ADD_RANGE(0x4F54, 1);
+	ADD_RANGE(R300_ZB_CNTL, 3);
+	ADD_RANGE(R300_ZB_FORMAT, 4);
+	ADD_RANGE_MARK(R300_ZB_DEPTHOFFSET, 1, MARK_CHECK_OFFSET);	/* check offset */
+	ADD_RANGE(R300_ZB_DEPTHPITCH, 1);
+	ADD_RANGE(R300_ZB_DEPTHCLEARVALUE, 1);
+	ADD_RANGE(R300_ZB_ZMASK_OFFSET, 13);
 
 	ADD_RANGE(R300_TX_FILTER_0, 16);
 	ADD_RANGE(R300_TX_FILTER1_0, 16);
@@ -229,7 +239,7 @@ void r300_init_reg_flags(struct drm_device *dev)
 	ADD_RANGE(R300_TX_BORDER_COLOR_0, 16);
 
 	/* Sporadic registers used as primitives are emitted */
-	ADD_RANGE(R300_RB3D_ZCACHE_CTLSTAT, 1);
+	ADD_RANGE(R300_ZB_ZCACHE_CTLSTAT, 1);
 	ADD_RANGE(R300_RB3D_DSTCACHE_CTLSTAT, 1);
 	ADD_RANGE(R300_VAP_INPUT_ROUTE_0_0, 8);
 	ADD_RANGE(R300_VAP_INPUT_ROUTE_1_0, 8);
@@ -243,6 +253,7 @@ void r300_init_reg_flags(struct drm_device *dev)
 		ADD_RANGE(R500_RS_INST_0, 16);
 		ADD_RANGE(R500_RB3D_COLOR_CLEAR_VALUE_AR, 2);
 		ADD_RANGE(R500_RB3D_CONSTANT_COLOR_AR, 2);
+		ADD_RANGE(R500_ZB_FIFO_SIZE, 2);
 	} else {
 		ADD_RANGE(R300_PFS_CNTL_0, 3);
 		ADD_RANGE(R300_PFS_NODE_0, 4);
@@ -390,15 +401,28 @@ static __inline__ int r300_emit_vpu(drm_radeon_private_t *dev_priv,
 	if (sz * 16 > cmdbuf->bufsz)
 		return -EINVAL;
 
-	BEGIN_RING(5 + sz * 4);
-	/* Wait for VAP to come to senses.. */
-	/* there is no need to emit it multiple times, (only once before VAP is programmed,
-	   but this optimization is for later */
-	OUT_RING_REG(R300_VAP_PVS_WAITIDLE, 0);
+	/* VAP is very sensitive so we purge cache before we program it
+	 * and we also flush its state before & after */
+	BEGIN_RING(6);
+	OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0));
+	OUT_RING(R300_RB3D_DC_FLUSH);
+	OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0));
+	OUT_RING(RADEON_WAIT_3D_IDLECLEAN);
+	OUT_RING(CP_PACKET0(R300_VAP_PVS_STATE_FLUSH_REG, 0));
+	OUT_RING(0);
+	ADVANCE_RING();
+	/* set flush flag */
+	dev_priv->track_flush |= RADEON_FLUSH_EMITED;
+
+	BEGIN_RING(3 + sz * 4);
 	OUT_RING_REG(R300_VAP_PVS_UPLOAD_ADDRESS, addr);
 	OUT_RING(CP_PACKET0_TABLE(R300_VAP_PVS_UPLOAD_DATA, sz * 4 - 1));
 	OUT_RING_TABLE((int *)cmdbuf->buf, sz * 4);
+	ADVANCE_RING();
 
+	BEGIN_RING(2);
+	OUT_RING(CP_PACKET0(R300_VAP_PVS_STATE_FLUSH_REG, 0));
+	OUT_RING(0);
 	ADVANCE_RING();
 
 	cmdbuf->buf += sz * 16;
@@ -426,6 +450,15 @@ static __inline__ int r300_emit_clear(drm_radeon_private_t *dev_priv,
 	OUT_RING_TABLE((int *)cmdbuf->buf, 8);
 	ADVANCE_RING();
 
+	BEGIN_RING(4);
+	OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0));
+	OUT_RING(R300_RB3D_DC_FLUSH);
+	OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0));
+	OUT_RING(RADEON_WAIT_3D_IDLECLEAN);
+	ADVANCE_RING();
+	/* set flush flag */
+	dev_priv->track_flush |= RADEON_FLUSH_EMITED;
+
 	cmdbuf->buf += 8 * 4;
 	cmdbuf->bufsz -= 8 * 4;
 
@@ -615,11 +648,19 @@ static __inline__ int r300_emit_raw_packet3(drm_radeon_private_t *dev_priv,
 	case RADEON_CNTL_BITBLT_MULTI:
 		return r300_emit_bitblt_multi(dev_priv, cmdbuf);
 
-	case RADEON_CP_INDX_BUFFER:	/* DRAW_INDX_2 without INDX_BUFFER seems to lock up the gpu */
+	case RADEON_CP_INDX_BUFFER:
+		/* DRAW_INDX_2 without INDX_BUFFER seems to lock up the gpu */
 		return r300_emit_indx_buffer(dev_priv, cmdbuf);
-	case RADEON_CP_3D_DRAW_IMMD_2:	/* triggers drawing using in-packet vertex data */
-	case RADEON_CP_3D_DRAW_VBUF_2:	/* triggers drawing of vertex buffers setup elsewhere */
-	case RADEON_CP_3D_DRAW_INDX_2:	/* triggers drawing using indices to vertex buffer */
+	case RADEON_CP_3D_DRAW_IMMD_2:
+		/* triggers drawing using in-packet vertex data */
+	case RADEON_CP_3D_DRAW_VBUF_2:
+		/* triggers drawing of vertex buffers setup elsewhere */
+	case RADEON_CP_3D_DRAW_INDX_2:
+		/* triggers drawing using indices to vertex buffer */
+		/* whenever we send vertex we clear flush & purge */
+		dev_priv->track_flush &= ~(RADEON_FLUSH_EMITED |
+					   RADEON_PURGE_EMITED);
+		break;
 	case RADEON_WAIT_FOR_IDLE:
 	case RADEON_CP_NOP:
 		/* these packets are safe */
@@ -715,16 +756,53 @@ static __inline__ int r300_emit_packet3(drm_radeon_private_t *dev_priv,
  */
 static __inline__ void r300_pacify(drm_radeon_private_t *dev_priv)
 {
+	uint32_t cache_z, cache_3d, cache_2d;
 	RING_LOCALS;
+	
+	cache_z = R300_ZC_FLUSH;
+	cache_2d = R300_RB2D_DC_FLUSH;
+	cache_3d = R300_RB3D_DC_FLUSH;
+	if (!(dev_priv->track_flush & RADEON_PURGE_EMITED)) {
+		/* we can purge, primitive where draw since last purge */
+		cache_z |= R300_ZC_FREE;
+		cache_2d |= R300_RB2D_DC_FREE;
+		cache_3d |= R300_RB3D_DC_FREE;
+	}
 
-	BEGIN_RING(6);
+	/* flush & purge zbuffer */
+	BEGIN_RING(2);
+	OUT_RING(CP_PACKET0(R300_ZB_ZCACHE_CTLSTAT, 0));
+	OUT_RING(cache_z);
+	ADVANCE_RING();
+	/* flush & purge 3d */
+	BEGIN_RING(2);
 	OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0));
-	OUT_RING(R300_RB3D_DSTCACHE_UNKNOWN_0A);
-	OUT_RING(CP_PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0));
-	OUT_RING(R300_RB3D_ZCACHE_UNKNOWN_03);
-	OUT_RING(CP_PACKET3(RADEON_CP_NOP, 0));
-	OUT_RING(0x0);
+	OUT_RING(cache_3d);
+	ADVANCE_RING();
+	/* flush & purge texture */
+	BEGIN_RING(2);
+	OUT_RING(CP_PACKET0(R300_TX_INVALTAGS, 0));
+	OUT_RING(0);
+	ADVANCE_RING();
+	/* FIXME: is this one really needed ? */
+	BEGIN_RING(2);
+	OUT_RING(CP_PACKET0(R300_RB3D_AARESOLVE_CTL, 0));
+	OUT_RING(0);
+	ADVANCE_RING();
+	BEGIN_RING(2);
+	OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0));
+	OUT_RING(RADEON_WAIT_3D_IDLECLEAN);
+	ADVANCE_RING();
+	/* flush & purge 2d through E2 as RB2D will trigger lockup */
+	BEGIN_RING(4);
+	OUT_RING(CP_PACKET0(R300_DSTCACHE_CTLSTAT, 0));
+	OUT_RING(cache_2d);
+	OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0));
+	OUT_RING(RADEON_WAIT_2D_IDLECLEAN |
+		 RADEON_WAIT_HOST_IDLECLEAN);
 	ADVANCE_RING();
+	/* set flush & purge flags */
+	dev_priv->track_flush |= RADEON_FLUSH_EMITED | RADEON_PURGE_EMITED;
 }
 
 /**
@@ -905,8 +983,7 @@ int r300_do_cp_cmdbuf(struct drm_device *dev,
 
 	DRM_DEBUG("\n");
 
-	/* See the comment above r300_emit_begin3d for why this call must be here,
-	 * and what the cleanup gotos are for. */
+	/* pacify */
 	r300_pacify(dev_priv);
 
 	if (cmdbuf->nbox <= R300_SIMULTANEOUS_CLIPRECTS) {
diff --git a/sys/dev/pci/drm/r300_reg.h b/sys/dev/pci/drm/r300_reg.h
index 0be01fc7451..d35dd39df70 100644
--- a/sys/dev/pci/drm/r300_reg.h
+++ b/sys/dev/pci/drm/r300_reg.h
@@ -320,7 +320,7 @@ USE OR OTHER DEALINGS IN THE SOFTWARE.
  * Therefore, I suspect writing zero to 0x2284 synchronizes the engine and
  * avoids bugs caused by still running shaders reading bad data from memory.
  */
-#define R300_VAP_PVS_WAITIDLE               0x2284 /* GUESS */
+#define R300_VAP_PVS_STATE_FLUSH_REG        0x2284
 
 /* Absolutely no clue what this register is about. */
 #define R300_VAP_UNKNOWN_2288               0x2288
@@ -516,7 +516,7 @@ USE OR OTHER DEALINGS IN THE SOFTWARE.
 /* gap */
 
 /* Zero to flush caches. */
-#define R300_TX_CNTL                        0x4100
+#define R300_TX_INVALTAGS                   0x4100
 #define R300_TX_FLUSH                       0x0
 
 /* The upper enable bits are guessed, based on fglrx reported limits. */
@@ -705,6 +705,27 @@ USE OR OTHER DEALINGS IN THE SOFTWARE.
 #		define R300_RS_ROUTE_1_UNKNOWN11         (1 << 11)
 /* END: Rasterization / Interpolators - many guesses */
 
+/* Hierarchical Z Enable */
+#define R300_SC_HYPERZ                   0x43a4
+#	define R300_SC_HYPERZ_DISABLE     (0 << 0)
+#	define R300_SC_HYPERZ_ENABLE      (1 << 0)
+#	define R300_SC_HYPERZ_MIN         (0 << 1)
+#	define R300_SC_HYPERZ_MAX         (1 << 1)
+#	define R300_SC_HYPERZ_ADJ_256     (0 << 2)
+#	define R300_SC_HYPERZ_ADJ_128     (1 << 2)
+#	define R300_SC_HYPERZ_ADJ_64      (2 << 2)
+#	define R300_SC_HYPERZ_ADJ_32      (3 << 2)
+#	define R300_SC_HYPERZ_ADJ_16      (4 << 2)
+#	define R300_SC_HYPERZ_ADJ_8       (5 << 2)
+#	define R300_SC_HYPERZ_ADJ_4       (6 << 2)
+#	define R300_SC_HYPERZ_ADJ_2       (7 << 2)
+#	define R300_SC_HYPERZ_HZ_Z0MIN_NO (0 << 5)
+#	define R300_SC_HYPERZ_HZ_Z0MIN    (1 << 5)
+#	define R300_SC_HYPERZ_HZ_Z0MAX_NO (0 << 6)
+#	define R300_SC_HYPERZ_HZ_Z0MAX    (1 << 6)
+
+#define R300_SC_EDGERULE                 0x43a8
+
 /* BEGIN: Scissors and cliprects */
 
 /* There are four clipping rectangles. Their corner coordinates are inclusive.
@@ -1344,6 +1365,7 @@ USE OR OTHER DEALINGS IN THE SOFTWARE.
 #define R300_RB3D_COLORPITCH2               0x4E40 /* GUESS */
 #define R300_RB3D_COLORPITCH3               0x4E44 /* GUESS */
 
+#define R300_RB3D_AARESOLVE_CTL             0x4E88
 /* gap */
 
 /* Guess by Vladimir.
@@ -1358,19 +1380,14 @@ USE OR OTHER DEALINGS IN THE SOFTWARE.
  * for this.
  * Bit (1<<8) is the "test" bit. so plain write is 6  - vd
  */
-#define R300_RB3D_ZSTENCIL_CNTL_0                   0x4F00
-#       define R300_RB3D_Z_DISABLED_1            0x00000010
-#       define R300_RB3D_Z_DISABLED_2            0x00000014
-#       define R300_RB3D_Z_TEST                  0x00000012
-#       define R300_RB3D_Z_TEST_AND_WRITE        0x00000016
-#       define R300_RB3D_Z_WRITE_ONLY		 0x00000006
-
-#       define R300_RB3D_Z_TEST                  0x00000012
-#       define R300_RB3D_Z_TEST_AND_WRITE        0x00000016
-#       define R300_RB3D_Z_WRITE_ONLY		 0x00000006
-#	define R300_RB3D_STENCIL_ENABLE		 0x00000001
-
-#define R300_RB3D_ZSTENCIL_CNTL_1                   0x4F04
+#define R300_ZB_CNTL                             0x4F00
+#	define R300_STENCIL_ENABLE		 (1 << 0)
+#	define R300_Z_ENABLE		         (1 << 1)
+#	define R300_Z_WRITE_ENABLE		 (1 << 2)
+#	define R300_Z_SIGNED_COMPARE		 (1 << 3)
+#	define R300_STENCIL_FRONT_BACK		 (1 << 4)
+
+#define R300_ZB_ZSTENCILCNTL                   0x4f04
 	/* functions */
 #	define R300_ZS_NEVER			0
 #	define R300_ZS_LESS			1
@@ -1390,52 +1407,166 @@ USE OR OTHER DEALINGS IN THE SOFTWARE.
 #	define R300_ZS_INVERT			5
 #	define R300_ZS_INCR_WRAP		6
 #	define R300_ZS_DECR_WRAP		7
+#	define R300_Z_FUNC_SHIFT		0
 	/* front and back refer to operations done for front
 	   and back faces, i.e. separate stencil function support */
-#	define R300_RB3D_ZS1_DEPTH_FUNC_SHIFT		0
-#	define R300_RB3D_ZS1_FRONT_FUNC_SHIFT		3
-#	define R300_RB3D_ZS1_FRONT_FAIL_OP_SHIFT	6
-#	define R300_RB3D_ZS1_FRONT_ZPASS_OP_SHIFT	9
-#	define R300_RB3D_ZS1_FRONT_ZFAIL_OP_SHIFT      12
-#	define R300_RB3D_ZS1_BACK_FUNC_SHIFT           15
-#	define R300_RB3D_ZS1_BACK_FAIL_OP_SHIFT        18
-#	define R300_RB3D_ZS1_BACK_ZPASS_OP_SHIFT       21
-#	define R300_RB3D_ZS1_BACK_ZFAIL_OP_SHIFT       24
-
-#define R300_RB3D_ZSTENCIL_CNTL_2                   0x4F08
-#	define R300_RB3D_ZS2_STENCIL_REF_SHIFT		0
-#	define R300_RB3D_ZS2_STENCIL_MASK		0xFF
-#	define R300_RB3D_ZS2_STENCIL_MASK_SHIFT	        8
-#	define R300_RB3D_ZS2_STENCIL_WRITE_MASK_SHIFT	16
+#	define R300_S_FRONT_FUNC_SHIFT	        3
+#	define R300_S_FRONT_SFAIL_OP_SHIFT	6
+#	define R300_S_FRONT_ZPASS_OP_SHIFT	9
+#	define R300_S_FRONT_ZFAIL_OP_SHIFT      12
+#	define R300_S_BACK_FUNC_SHIFT           15
+#	define R300_S_BACK_SFAIL_OP_SHIFT       18
+#	define R300_S_BACK_ZPASS_OP_SHIFT       21
+#	define R300_S_BACK_ZFAIL_OP_SHIFT       24
+
+#define R300_ZB_STENCILREFMASK                        0x4f08
+#	define R300_STENCILREF_SHIFT       0
+#	define R300_STENCILREF_MASK        0x000000ff
+#	define R300_STENCILMASK_SHIFT      8
+#	define R300_STENCILMASK_MASK       0x0000ff00
+#	define R300_STENCILWRITEMASK_SHIFT 16
+#	define R300_STENCILWRITEMASK_MASK  0x00ff0000
 
 /* gap */
 
-#define R300_RB3D_ZSTENCIL_FORMAT                   0x4F10
-#	define R300_DEPTH_FORMAT_16BIT_INT_Z     (0 << 0)
-#	define R300_DEPTH_FORMAT_24BIT_INT_Z     (2 << 0)
-	/* 16 bit format or some aditional bit ? */
-#	define R300_DEPTH_FORMAT_UNK32          (32 << 0)
+#define R300_ZB_FORMAT                             0x4f10
+#	define R300_DEPTHFORMAT_16BIT_INT_Z   (0 << 0)
+#	define R300_DEPTHFORMAT_16BIT_13E3    (1 << 0)
+#	define R300_DEPTHFORMAT_24BIT_INT_Z_8BIT_STENCIL   (2 << 0)
+/* reserved up to (15 << 0) */
+#	define R300_INVERT_13E3_LEADING_ONES  (0 << 4)
+#	define R300_INVERT_13E3_LEADING_ZEROS (1 << 4)
 
-#define R300_RB3D_EARLY_Z                           0x4F14
-#	define R300_EARLY_Z_DISABLE              (0 << 0)
-#	define R300_EARLY_Z_ENABLE               (1 << 0)
+#define R300_ZB_ZTOP                             0x4F14
+#	define R300_ZTOP_DISABLE                 (0 << 0)
+#	define R300_ZTOP_ENABLE                  (1 << 0)
 
 /* gap */
 
-#define R300_RB3D_ZCACHE_CTLSTAT            0x4F18 /* GUESS */
-#       define R300_RB3D_ZCACHE_UNKNOWN_01  0x1
-#       define R300_RB3D_ZCACHE_UNKNOWN_03  0x3
+#define R300_ZB_ZCACHE_CTLSTAT            0x4f18
+#       define R300_ZB_ZCACHE_CTLSTAT_ZC_FLUSH_NO_EFFECT      (0 << 0)
+#       define R300_ZB_ZCACHE_CTLSTAT_ZC_FLUSH_FLUSH_AND_FREE (1 << 0)
+#       define R300_ZB_ZCACHE_CTLSTAT_ZC_FREE_NO_EFFECT       (0 << 1)
+#       define R300_ZB_ZCACHE_CTLSTAT_ZC_FREE_FREE            (1 << 1)
+#       define R300_ZB_ZCACHE_CTLSTAT_ZC_BUSY_IDLE            (0 << 31)
+#       define R300_ZB_ZCACHE_CTLSTAT_ZC_BUSY_BUSY            (1 << 31)
+
+#define R300_ZB_BW_CNTL                     0x4f1c
+#	define R300_HIZ_DISABLE                              (0 << 0)
+#	define R300_HIZ_ENABLE                               (1 << 0)
+#	define R300_HIZ_MIN                                  (0 << 1)
+#	define R300_HIZ_MAX                                  (1 << 1)
+#	define R300_FAST_FILL_DISABLE                        (0 << 2)
+#	define R300_FAST_FILL_ENABLE                         (1 << 2)
+#	define R300_RD_COMP_DISABLE                          (0 << 3)
+#	define R300_RD_COMP_ENABLE                           (1 << 3)
+#	define R300_WR_COMP_DISABLE                          (0 << 4)
+#	define R300_WR_COMP_ENABLE                           (1 << 4)
+#	define R300_ZB_CB_CLEAR_RMW                          (0 << 5)
+#	define R300_ZB_CB_CLEAR_CACHE_LINEAR                 (1 << 5)
+#	define R300_FORCE_COMPRESSED_STENCIL_VALUE_DISABLE   (0 << 6)
+#	define R300_FORCE_COMPRESSED_STENCIL_VALUE_ENABLE    (1 << 6)
+
+#	define R500_ZEQUAL_OPTIMIZE_ENABLE                   (0 << 7)
+#	define R500_ZEQUAL_OPTIMIZE_DISABLE                  (1 << 7)
+#	define R500_SEQUAL_OPTIMIZE_ENABLE                   (0 << 8)
+#	define R500_SEQUAL_OPTIMIZE_DISABLE                  (1 << 8)
+
+#	define R500_BMASK_ENABLE                             (0 << 10)
+#	define R500_BMASK_DISABLE                            (1 << 10)
+#	define R500_HIZ_EQUAL_REJECT_DISABLE                 (0 << 11)
+#	define R500_HIZ_EQUAL_REJECT_ENABLE                  (1 << 11)
+#	define R500_HIZ_FP_EXP_BITS_DISABLE                  (0 << 12)
+#	define R500_HIZ_FP_EXP_BITS_1                        (1 << 12)
+#	define R500_HIZ_FP_EXP_BITS_2                        (2 << 12)
+#	define R500_HIZ_FP_EXP_BITS_3                        (3 << 12)
+#	define R500_HIZ_FP_EXP_BITS_4                        (4 << 12)
+#	define R500_HIZ_FP_EXP_BITS_5                        (5 << 12)
+#	define R500_HIZ_FP_INVERT_LEADING_ONES               (0 << 15)
+#	define R500_HIZ_FP_INVERT_LEADING_ZEROS              (1 << 15)
+#	define R500_TILE_OVERWRITE_RECOMPRESSION_ENABLE      (0 << 16)
+#	define R500_TILE_OVERWRITE_RECOMPRESSION_DISABLE     (1 << 16)
+#	define R500_CONTIGUOUS_6XAA_SAMPLES_ENABLE           (0 << 17)
+#	define R500_CONTIGUOUS_6XAA_SAMPLES_DISABLE          (1 << 17)
+#	define R500_PEQ_PACKING_DISABLE                      (0 << 18)
+#	define R500_PEQ_PACKING_ENABLE                       (1 << 18)
+#	define R500_COVERED_PTR_MASKING_DISABLE              (0 << 18)
+#	define R500_COVERED_PTR_MASKING_ENABLE               (1 << 18)
+
 
 /* gap */
 
-#define R300_RB3D_DEPTHOFFSET               0x4F20
-#define R300_RB3D_DEPTHPITCH                0x4F24
-#       define R300_DEPTHPITCH_MASK              0x00001FF8 /* GUESS */
-#       define R300_DEPTH_TILE_ENABLE            (1 << 16) /* GUESS */
-#       define R300_DEPTH_MICROTILE_ENABLE       (1 << 17) /* GUESS */
-#       define R300_DEPTH_ENDIAN_NO_SWAP         (0 << 18) /* GUESS */
-#       define R300_DEPTH_ENDIAN_WORD_SWAP       (1 << 18) /* GUESS */
-#       define R300_DEPTH_ENDIAN_DWORD_SWAP      (2 << 18) /* GUESS */
+/* Z Buffer Address Offset.
+ * Bits 31 to 5 are used for aligned Z buffer address offset for macro tiles.
+ */
+#define R300_ZB_DEPTHOFFSET               0x4f20
+
+/* Z Buffer Pitch and Endian Control */
+#define R300_ZB_DEPTHPITCH                0x4f24
+#       define R300_DEPTHPITCH_MASK              0x00003FFC
+#       define R300_DEPTHMACROTILE_DISABLE      (0 << 16)
+#       define R300_DEPTHMACROTILE_ENABLE       (1 << 16)
+#       define R300_DEPTHMICROTILE_LINEAR       (0 << 17)
+#       define R300_DEPTHMICROTILE_TILED        (1 << 17)
+#       define R300_DEPTHMICROTILE_TILED_SQUARE (2 << 17)
+#       define R300_DEPTHENDIAN_NO_SWAP         (0 << 18)
+#       define R300_DEPTHENDIAN_WORD_SWAP       (1 << 18)
+#       define R300_DEPTHENDIAN_DWORD_SWAP      (2 << 18)
+#       define R300_DEPTHENDIAN_HALF_DWORD_SWAP (3 << 18)
+
+/* Z Buffer Clear Value */
+#define R300_ZB_DEPTHCLEARVALUE                  0x4f28
+
+#define R300_ZB_ZMASK_OFFSET			 0x4f30
+#define R300_ZB_ZMASK_PITCH			 0x4f34
+#define R300_ZB_ZMASK_WRINDEX			 0x4f38
+#define R300_ZB_ZMASK_DWORD			 0x4f3c
+#define R300_ZB_ZMASK_RDINDEX			 0x4f40
+
+/* Hierarchical Z Memory Offset */
+#define R300_ZB_HIZ_OFFSET                       0x4f44
+
+/* Hierarchical Z Write Index */
+#define R300_ZB_HIZ_WRINDEX                      0x4f48
+
+/* Hierarchical Z Data */
+#define R300_ZB_HIZ_DWORD                        0x4f4c
+
+/* Hierarchical Z Read Index */
+#define R300_ZB_HIZ_RDINDEX                      0x4f50
+
+/* Hierarchical Z Pitch */
+#define R300_ZB_HIZ_PITCH                        0x4f54
+
+/* Z Buffer Z Pass Counter Data */
+#define R300_ZB_ZPASS_DATA                       0x4f58
+
+/* Z Buffer Z Pass Counter Address */
+#define R300_ZB_ZPASS_ADDR                       0x4f5c
+
+/* Depth buffer X and Y coordinate offset */
+#define R300_ZB_DEPTHXY_OFFSET                   0x4f60
+#	define R300_DEPTHX_OFFSET_SHIFT  1
+#	define R300_DEPTHX_OFFSET_MASK   0x000007FE
+#	define R300_DEPTHY_OFFSET_SHIFT  17
+#	define R300_DEPTHY_OFFSET_MASK   0x07FE0000
+
+/* Sets the fifo sizes */
+#define R500_ZB_FIFO_SIZE                        0x4fd0
+#	define R500_OP_FIFO_SIZE_FULL   (0 << 0)
+#	define R500_OP_FIFO_SIZE_HALF   (1 << 0)
+#	define R500_OP_FIFO_SIZE_QUATER (2 << 0)
+#	define R500_OP_FIFO_SIZE_EIGTHS (4 << 0)
+
+/* Stencil Reference Value and Mask for backfacing quads */
+/* R300_ZB_STENCILREFMASK handles front face */
+#define R500_ZB_STENCILREFMASK_BF                0x4fd4
+#	define R500_STENCILREF_SHIFT       0
+#	define R500_STENCILREF_MASK        0x000000ff
+#	define R500_STENCILMASK_SHIFT      8
+#	define R500_STENCILMASK_MASK       0x0000ff00
+#	define R500_STENCILWRITEMASK_SHIFT 16
+#	define R500_STENCILWRITEMASK_MASK  0x00ff0000
 
 /* BEGIN: Vertex program instruction set */