rev 1.71

Add some special case code to fix a problem with the BCM5704 in TBI (fiber)
mode. The 5704 apparently has some s00p3r s33kr1t registers for setting
the advertisement of pause frame ability (i.e flow control) when in
autoneg mode. If we don't set these registers correctly, we may not
be able to negotiate a proper link with some switches. (Symptom is that
the NIC reports the link as up (PCS synched) but no traffic can be
exchanged.)

rev 1.73

Commit patch to supress spurious link change events. Apparently, with
copper NICs, a link change event is posted whenever MII autopolling is
toggled off and on, which happens whenever someone calls
bge_miibus_readreg() or bge_miibus_writereg() to access the PHY
registers. This means anytime someone called the SIOCGIFMEDIA ioctl
on a bge interface, the link would reset. Even a simple "ifconfig bge0"
would do it, though other apps like dhclient or the PPPoE daemon could
trigger it as well. An obvious symptom of this problem is lots of
"bgeX: gigabit link up" messages appearing on the console for no
apparent reason.

Through experimentation, I determined that when a real link change
event occurs, the BGE_MIMODE_AUTOPOLL in the BGE_MI_MODE register
is always set, so now if we have a copper NIC and an link change
event occurs and the BGE_MIMODE_AUTOPOLL bit is clear, we ignore
the event.

Note that this does not apply to the original BCM5700 chip since we
use a different method for sensing link changes with that chip (the
status block method was broken), nor to fiber optic NICs since they
don't use the GMII PHY access registers.

From FreeBSD

ok deraadt@

1 files changed, 38 insertions, 1 deletions

diff --git a/sys/dev/pci/if_bgereg.h b/sys/dev/pci/if_bgereg.h
index e780dfc4a12..dea71d0c3fa 100644
--- a/sys/dev/pci/if_bgereg.h
+++ b/sys/dev/pci/if_bgereg.h
@@ -1,4 +1,4 @@
-/* $OpenBSD: if_bgereg.h,v 1.12 2004/10/31 06:59:25 brad Exp $ */
+/* $OpenBSD: if_bgereg.h,v 1.13 2004/11/11 18:35:41 brad Exp $ */
 /*
  * Copyright (c) 2001 Wind River Systems
  * Copyright (c) 1997, 1998, 1999, 2001
@@ -529,6 +529,10 @@
 #define BGE_RX_BD_RULES_CTL15		0x04F8
 #define BGE_RX_BD_RULES_MASKVAL15	0x04FC
 #define BGE_RX_RULES_CFG		0x0500
+#define BGE_SERDES_CFG			0x0590
+#define BGE_SERDES_STS			0x0594
+#define BGE_SGDIG_CFG			0x05B0
+#define BGE_SGDIG_STS			0x05B4
 #define BGE_RX_STATS			0x0800
 #define BGE_TX_STATS			0x0880
 
@@ -659,6 +663,39 @@
 #define BGE_RXRULEMASK_VALUE		0x0000FFFF
 #define BGE_RXRULEMASK_MASKVAL		0xFFFF0000
 
+/* SERDES configuration register */
+#define BGE_SERDESCFG_RXR		0x00000007 /* phase interpolator */
+#define BGE_SERDESCFG_RXG		0x00000018 /* rx gain setting */
+#define BGE_SERDESCFG_RXEDGESEL		0x00000040 /* rising/falling egde */
+#define BGE_SERDESCFG_TX_BIAS		0x00000380 /* TXDAC bias setting */
+#define BGE_SERDESCFG_IBMAX		0x00000400 /* bias current +25% */
+#define BGE_SERDESCFG_IBMIN		0x00000800 /* bias current -25% */
+#define BGE_SERDESCFG_TXMODE		0x00001000
+#define BGE_SERDESCFG_TXEDGESEL		0x00002000 /* rising/falling edge */
+#define BGE_SERDESCFG_MODE		0x00004000 /* TXCP/TXCN disabled */
+#define BGE_SERDESCFG_PLLTEST		0x00008000 /* PLL test mode */
+#define BGE_SERDESCFG_CDET		0x00010000 /* comma detect enable */
+#define BGE_SERDESCFG_TBILOOP		0x00020000 /* local loopback */
+#define BGE_SERDESCFG_REMLOOP		0x00040000 /* remote loopback */
+#define BGE_SERDESCFG_INVPHASE		0x00080000 /* Reverse 125Mhz clock */
+#define BGE_SERDESCFG_12REGCTL		0x00300000 /* 1.2v regulator ctl */
+#define BGE_SERDESCFG_REGCTL		0x00C00000 /* regulator ctl (2.5v) */
+
+/* SERDES status register */
+#define BGE_SERDESSTS_RXSTAT		0x0000000F /* receive status bits */
+#define BGE_SERDESSTS_CDET		0x00000010 /* comma code detected */
+
+/* SGDIG config (not documented) */
+#define BGE_SGDIGCFG_PAUSE_CAP		0x00000800
+#define BGE_SGDIGCFG_ASYM_PAUSE		0x00001000
+#define BGE_SGDIGCFG_SEND		0x40000000
+#define BGE_SGDIGCFG_AUTO		0x80000000
+
+/* SGDIG status (not documented) */
+#define BGE_SGDIGSTS_PAUSE_CAP		0x00080000
+#define BGE_SGDIGSTS_ASYM_PAUSE		0x00100000
+#define BGE_SGDIGSTS_DONE		0x00000002
+
 /* MI communication register */
 #define BGE_MICOMM_DATA			0x0000FFFF
 #define BGE_MICOMM_REG			0x001F0000