Support for new Marvell based Gigabit Ethernet adapters

ok deraadt@

1 files changed, 181 insertions, 0 deletions

diff --git a/sys/dev/pci/yukonreg.h b/sys/dev/pci/yukonreg.h
new file mode 100644
index 00000000000..d0280e46f27
--- /dev/null
+++ b/sys/dev/pci/yukonreg.h
@@ -0,0 +1,181 @@
+/*	$OpenBSD: yukonreg.h,v 1.1 2003/08/01 04:46:13 nate Exp $ */
+/*
+ * Copyright (c) 2003 Nathan L. Binkert
+ * All rights reserved.
+ *
+ * Permission to redistribute, use, copy, and modify this software
+ * without fee is hereby granted, provided that the following
+ * conditions are met:
+ *
+ * 1. This entire notice is included in all source code copies of any
+ *    software which is or includes a copy or modification of this
+ *    software.
+ * 2. The name of the author may not be used to endorse or promote
+ *    products derived from this software without specific prior
+ *    written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS
+ * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
+ * GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/* General Purpose Status Register (GPSR) */
+#define YUKON_GPSR		0x0000
+
+#define YU_GPSR_SPEED		0x8000	/* speed 0 - 10Mbps, 1 - 100Mbps */
+#define YU_GPSR_DUPLEX		0x4000	/* 0 - half duplex, 1 - full duplex */
+#define YU_GPSR_FCTL_TX		0x2000	/* flow control */
+#define YU_GPSR_LINK		0x1000	/* link status (down/up) */
+#define YU_GPSR_PAUSE		0x0800	/* flow control enable/disable */
+#define YU_GPSR_TX_IN_PROG	0x0400	/* transmit in progress */
+#define YU_GPSR_EXCESS_COL	0x0200	/* excessive collisions occurred */
+#define YU_GPSR_LATE_COL	0x0100	/* late collision occurred */
+#define YU_GPSR_MII_PHY_STC	0x0020	/* MII PHY status change */
+#define YU_GPSR_GIG_SPEED	0x0010	/* Gigabit Speed (0 - use speed bit) */
+#define YU_GPSR_PARTITION	0x0008	/* partition mode */
+#define YU_GPSR_FCTL_RX		0x0004	/* flow control enable/disable */
+#define YU_GPSR_PROMS_EN	0x0002	/* promiscuous mode enable/disable */
+
+/* General Purpose Control Register (GPCR) */
+#define YUKON_GPCR		0x0004
+
+#define YU_GPCR_FCTL_TX		0x2000	/* Transmit flow control 802.3x */
+#define YU_GPCR_TXEN		0x1000	/* Transmit Enable */
+#define YU_GPCR_RXEN		0x0800	/* Receive Enable */
+#define YU_GPCR_LPBK		0x0200	/* Loopback Enable */
+#define YU_GPCR_PAR		0x0100	/* Partition Enable */
+#define YU_GPCR_GIG		0x0080	/* Gigabit Speed */
+#define YU_GPCR_FLP		0x0040	/* Force Link Pass */
+#define YU_GPCR_DUPLEX		0x0020	/* Duplex Enable */
+#define YU_GPCR_FCTL_RX		0x0010	/* Receive flow control 802.3x */
+#define YU_GPCR_SPEED		0x0008	/* Port Speed */
+#define YU_GPCR_DPLX_EN		0x0004	/* Enable Auto-Update for duplex */
+#define YU_GPCR_FCTL_EN		0x0002	/* Enabel Auto-Update for 802.3x */
+#define YU_GPCR_SPEED_EN	0x0001	/* Enable Auto-Update for speed */
+
+/* Transmit Control Register (TCR) */
+#define YUKON_TCR		0x0008
+
+#define YU_TCR_FJ		0x8000	/* force jam / flow control */
+#define YU_TCR_CRCD		0x4000	/* insert CRC (0 - enable) */
+#define YU_TCR_PADD		0x2000	/* pad packets to 64b (0 - enable) */
+#define YU_TCR_COLTH		0x1c00	/* collision threshold */
+
+/* Receive Control Register (RCR) */
+#define YUKON_RCR		0x000c
+
+#define YU_RCR_UFLEN		0x8000	/* unicast filter enable */
+#define YU_RCR_MUFLEN		0x4000	/* multicast filter enable */
+#define YU_RCR_CRCR		0x2000	/* remove CRC */
+#define YU_RCR_PASSFC		0x1000	/* pass flow control packets */
+
+/* Transmit Flow Control Register (TFCR) */
+#define YUKON_TFCR		0x0010	/* Pause Time */
+
+/* Transmit Parameter Register (TPR) */
+#define YUKON_TPR		0x0014
+
+#define YU_TPR_JAM_LEN(x)	(((x) & 0x3) << 14)
+#define YU_TPR_JAM_IPG(x)	(((x) & 0x1f) << 9)
+#define YU_TPR_JAM2DATA_IPG(x)	(((x) & 0x1f) << 4)
+
+/* Serial Mode Register (SMR) */
+#define YUKON_SMR		0x0018
+
+#define YU_SMR_DATA_BLIND(x)	(((x) & 0x1f) << 11)
+#define YU_SMR_LIMIT4		0x0400	/* reset after 16 / 4 collisions */
+#define YU_SMR_MFL_JUMBO	0x0100	/* max frame length for jumbo frames */
+#define YU_SMR_MFL_VLAN		0x0200	/* max frame length + vlan tag */
+#define YU_SMR_IPG_DATA(x)	((x) & 0x1f)
+
+/* Source Address Low #1 (SAL1) */
+#define YUKON_SAL1		0x001c	/* SA1[15:0] */
+
+/* Source Address Middle #1 (SAM1) */
+#define YUKON_SAM1		0x0020	/* SA1[31:16] */
+
+/* Source Address High #1 (SAH1) */
+#define YUKON_SAH1		0x0024	/* SA1[47:32] */
+
+/* Source Address Low #2 (SAL2) */
+#define YUKON_SAL2		0x0028	/* SA2[15:0] */
+
+/* Source Address Middle #2 (SAM2) */
+#define YUKON_SAM2		0x002c	/* SA2[31:16] */
+
+/* Source Address High #2 (SAH2) */
+#define YUKON_SAH2		0x0030	/* SA2[47:32] */
+
+/* Multicatst Address Hash Register 1 (MCAH1) */
+#define YUKON_MCAH1		0x0034
+
+/* Multicatst Address Hash Register 2 (MCAH2) */
+#define YUKON_MCAH2		0x0038
+
+/* Multicatst Address Hash Register 3 (MCAH3) */
+#define YUKON_MCAH3		0x003c
+
+/* Multicatst Address Hash Register 4 (MCAH4) */
+#define YUKON_MCAH4		0x0040
+
+/* Transmit Interrupt Register (TIR) */
+#define YUKON_TIR		0x0044
+
+#define YU_TIR_OUT_UNICAST	0x0001	/* Num Unicast Packets Transmitted */
+#define YU_TIR_OUT_BROADCAST	0x0002	/* Num Broadcast Packets Transmitted */
+#define YU_TIR_OUT_PAUSE	0x0004	/* Num Pause Packets Transmitted */
+#define YU_TIR_OUT_MULTICAST	0x0008	/* Num Multicast Packets Transmitted */
+#define YU_TIR_OUT_OCTETS	0x0030	/* Num Bytes Transmitted */
+#define YU_TIR_OUT_64_OCTETS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_127_OCTETS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_255_OCTETS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_511_OCTETS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_1023_OCTETS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_1518_OCTETS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_MAX_OCTETS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_SPARE	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_COLLISIONS	0x0000	/* Num Packets Transmitted */
+#define YU_TIR_OUT_LATE		0x0000	/* Num Packets Transmitted */
+
+/* Receive Interrupt Register (RIR) */
+#define YUKON_RIR		0x0048
+
+/* Transmit and Receive Interrupt Register (TRIR) */
+#define YUKON_TRIR		0x004c
+
+/* Transmit Interrupt Mask Register (TIMR) */
+#define YUKON_TIMR		0x0050
+
+/* Receive Interrupt Mask Register (RIMR) */
+#define YUKON_RIMR		0x0054
+
+/* Transmit and Receive Interrupt Mask Register (TRIMR) */
+#define YUKON_TRIMR		0x0058
+
+/* SMI Control Register (SMICR) */
+#define YUKON_SMICR		0x0080
+
+#define YU_SMICR_PHYAD(x)	(((x) & 0x1f) << 11)
+#define YU_SMICR_REGAD(x)	(((x) & 0x1f) << 6)
+#define YU_SMICR_OPCODE		0x0020	/* opcode (0 - write, 1 - read) */
+#define YU_SMICR_OP_READ	0x0020	/* opcode read */
+#define YU_SMICR_OP_WRITE	0x0000	/* opcode write */
+#define YU_SMICR_READ_VALID	0x0010	/* read valid */
+#define YU_SMICR_BUSY		0x0008	/* busy (writing) */
+
+/* SMI Data Register (SMIDR) */
+#define YUKON_SMIDR		0x0084
+
+/* PHY Addres Register (PAR) */
+#define YUKON_PAR		0x0088
+
+#define YU_PAR_MIB_CLR		0x0020	/* MIB Counters Clear Mode */
+#define YU_PAR_LOAD_TSTCNT	0x0010	/* Load count 0xfffffff0 into cntr */