spelling fixes in comments and one printf; from j sisson

1 files changed, 8 insertions, 8 deletions

diff --git a/sys/dev/pci/if_jme.c b/sys/dev/pci/if_jme.c
index a47b2172d8c..092789f33a0 100644
--- a/sys/dev/pci/if_jme.c
+++ b/sys/dev/pci/if_jme.c
@@ -1,4 +1,4 @@
-/*	$OpenBSD: if_jme.c,v 1.51 2019/03/29 17:25:44 sthen Exp $	*/
+/*	$OpenBSD: if_jme.c,v 1.52 2019/05/27 20:42:00 jmc Exp $	*/
 /*-
  * Copyright (c) 2008, Pyun YongHyeon <yongari@FreeBSD.org>
  * All rights reserved.
@@ -233,7 +233,7 @@ jme_miibus_statchg(struct device *dev)
 	 * Disabling Rx/Tx MACs have a side-effect of resetting
 	 * JME_TXNDA/JME_RXNDA register to the first address of
 	 * Tx/Rx descriptor address. So driver should reset its
-	 * internal procucer/consumer pointer and reclaim any
+	 * internal producer/consumer pointer and reclaim any
 	 * allocated resources.  Note, just saving the value of
 	 * JME_TXNDA and JME_RXNDA registers before stopping MAC
 	 * and restoring JME_TXNDA/JME_RXNDA register is not
@@ -277,7 +277,7 @@ jme_miibus_statchg(struct device *dev)
 
 	/*
 	 * Reuse configured Rx descriptors and reset
-	 * procuder/consumer index.
+	 * producer/consumer index.
 	 */
 	sc->jme_cdata.jme_rx_cons = 0;
 
@@ -550,7 +550,7 @@ jme_attach(struct device *parent, struct device *self, void *aux)
 	 * JMC250 supports both memory mapped and I/O register space
 	 * access.  Because I/O register access should use different
 	 * BARs to access registers it's waste of time to use I/O
-	 * register spce access.  JMC250 uses 16K to map entire memory
+	 * register space access.  JMC250 uses 16K to map entire memory
 	 * space.
 	 */
 
@@ -984,7 +984,7 @@ jme_dma_free(struct jme_softc *sc)
 /*
  * Unlike other ethernet controllers, JMC250 requires
  * explicit resetting link speed to 10/100Mbps as gigabit
- * link will cunsume more power than 375mA.
+ * link will consume more power than 375mA.
  * Note, we reset the link speed to 10/100Mbps with
  * auto-negotiation but we don't know whether that operation
  * would succeed or not as we have no control after powering
@@ -1169,7 +1169,7 @@ jme_encap(struct jme_softc *sc, struct mbuf *m)
 	sc->jme_cdata.jme_tx_prod = prod;
 	/*
 	 * Finally request interrupt and give the first descriptor
-	 * owenership to hardware.
+	 * ownership to hardware.
 	 */
 	desc = txd->tx_desc;
 	desc->flags |= htole32(JME_TD_OWN | JME_TD_INTR);
@@ -1534,7 +1534,7 @@ jme_txeof(struct jme_softc *sc)
 		/*
 		 * Only the first descriptor of multi-descriptor
 		 * transmission is updated so driver have to skip entire
-		 * chained buffers for the transmiited frame. In other
+		 * chained buffers for the transmitted frame. In other
 		 * words, JME_TD_OWN bit is valid only at the first
 		 * descriptor of a multi-descriptor transmission.
 		 */
@@ -2110,7 +2110,7 @@ jme_stop_rx(struct jme_softc *sc)
 			break;
 	}
 	if (i == 0)
-		printf("%s: stopping recevier timeout!\n", sc->sc_dev.dv_xname);
+		printf("%s: stopping receiver timeout!\n", sc->sc_dev.dv_xname);
 }
 
 void