diff options
Diffstat (limited to 'distrib/notes/hp300')
| -rw-r--r-- | distrib/notes/hp300/install | 82 |
1 files changed, 8 insertions, 74 deletions
diff --git a/distrib/notes/hp300/install b/distrib/notes/hp300/install index 4f8c2a12a58..79d31e648cd 100644 --- a/distrib/notes/hp300/install +++ b/distrib/notes/hp300/install @@ -1,4 +1,4 @@ -dnl $OpenBSD: install,v 1.18 2002/03/18 22:40:04 miod Exp $ +dnl $OpenBSD: install,v 1.19 2002/03/30 22:52:57 miod Exp $ OpenBSDInstallPrelude dnl No extra line, this has to stick to the geometry notes paragraph. The file `HP-IB.geometry' has geometry information for several HP-IB @@ -110,33 +110,13 @@ OpenBSDBootMsgs or vt100 compatible terminal; nothing else is supported. (If your terminal type is xterm, just use vt100). - After entering the terminal type you will be asked whether you - wish to do an "(I)nstall" or an "(U)pgrade". Enter 'I' for a - fresh install or 'U' to upgrade an existing installation. - - You will be presented with a welcome message and asked if - you really wish to install (or upgrade). Assuming you - answered yes, the install program will then tell you which - disks of that type it can install on, and ask you which it - should use. The name of the disk is typically "hd0" for - HPIB/CS80 drives or "sd0" for SCSI drives. Reply with the - name of your disk. +OpenBDSInstallPart3({:- or "hd0" for HPIB/CS80 drives-:}) Please note that, if you choose to have your root (/) filesystem on a SCSI drive, that only device ID 4, 5 and 6 (that is, sd4, sd5 and sd6 from OpenBSD's point of view) are bootable. - Next the disk label which defines the layout of the OpenBSD - file systems must be set up. The installation script will - invoke an interactive editor allowing you to do this. Note - that partition 'c' inside this disk label should ALWAYS - reflect the entire disk, including any non-OpenBSD portions. - The root file system should be in partition 'a', and swap - is usually in partition 'b'. It is recommended that you - create separate partitions for /usr and /var, and if you - have room for it, one for /home. For help in the disk - label editor, enter '?' or 'M' to view the manual page (see - the info on the ``-E'' flag). +OpenBSDInstallPart4 Since the target disk will become the boot disk for your new OpenBSD/MACHINE installation, the disklabel program will restrict @@ -145,57 +125,11 @@ OpenBSDBootMsgs plan to install a bootblock on this disk, you can reclaim this space with the 'b' command. - The swap partition (usually 'b') should have a type of "swap", all - other native OpenBSD partitions should have a type of "4.2BSD". - Block and fragment sizes are usually 8192 and 1024 bytes, but can - also be 4096 and 512 or even 16384 and 2048 bytes. - - The install program will now label your disk and ask which file - systems should be created on which partitions. It will - automatically select the 'a' partition to be the root file system. - Next it will ask for which disk and partition you want a file system - created on. This will be the same as the disk name (e.g. "hd0") - with the letter identifying the partition (e.g. "d") appended (e.g. - "hd0d"). Then it will ask where this partition is to be mounted, - e.g. /usr. This process will be repeated until you enter "done". - - At this point you will be asked to confirm that the file system - information you have entered is correct, and given an opportunity - to change the file system table. Next it will create the new file - systems as specified, OVERWRITING ANY EXISTING DATA. This is the - point of no return. - - After all your file systems have been created, the install program - will give you an opportunity to configure the network. The network - configuration you enter (if any) can then be used to do the install - from another system using NFS, HTTP or FTP, and will also be the - configuration used by the system after the installation is complete. - - If you select to configure the network, the install program will - ask you for a name of your system and the DNS domain name to use. - Note that the host name should be without the domain part, and that - the domain name should NOT {:-include-:} the host name part. - - Next the system will give you a list of network interfaces you can - configure. For each network interface you select to configure, it - will ask for the IP address to use, the symbolic host name to use, - the netmask to use and any interface-specific flags to set. No - interface-specific flags should be required. - - After all network interfaces have been configured the install - program will ask for a default route and IP address of the primary - name server to use. You will also be presented with an opportunity - to edit the host table. - - At this point you will be allowed to edit the file system table - that will be used for the remainder of the installation and that - will be used by the finished system, following which the new file - systems will be mounted to complete the installation. - - After these preparatory steps have been completed, you will be - able to extract the distribution sets onto your system. There - are several install methods supported; FTP, HTTP, tape, CD-ROM, NFS - or a local disk partition. +OpenBSDDInstallPart5(sd0) + +OpenBSDInstallNet + +OpenBSDInstallNet2({:-CD-ROM, NFS, -:}) OpenBSDFTPInstall |