summaryrefslogtreecommitdiff
path: root/distrib/notes/macppc
diff options
context:
space:
mode:
Diffstat (limited to 'distrib/notes/macppc')
-rw-r--r--distrib/notes/macppc/install100
1 files changed, 17 insertions, 83 deletions
diff --git a/distrib/notes/macppc/install b/distrib/notes/macppc/install
index fafa76f0d13..ea55877cd89 100644
--- a/distrib/notes/macppc/install
+++ b/distrib/notes/macppc/install
@@ -1,3 +1,4 @@
+dnl $OpenBSD: install,v 1.9 2002/03/30 22:52:57 miod Exp $
OpenBSDInstallShortPrelude
Before you begin, you should decide if OpenBSD is to be installed
@@ -37,19 +38,7 @@ OpenBSDBootMsgs
You will next be asked for your terminal type. You should just
hit return to select the default (vt220).
- Now you will be asked whether you wish to do an "install"
- or an "upgrade". Enter 'i' for a fresh install or 'u' to
- upgrade an existing installation.
-
- You will be presented with a welcome message and asked if
- you really wish to install (or upgrade). Assuming you
- answered yes, you will be asked which terminal type to use.
- You should just hit return to select the default (vt220).
-
- The install program will then tell you which disks of that
- type it can install on, and ask you which it should use. The
- name of the disk is typically "wd0" for IDE/ATA drives or
- "sd0" for SCSI drives. Reply with the name of your disk.
+OpenBSDInstallPart3({:- or "wd0" for IDE/ATA drives-:})
Next you will have to edit or create a disklabel for the disk
OpenBSD is being installed on. If there are any existing
@@ -117,80 +106,25 @@ OpenBSDBootMsgs
correct this. Note that you should make OpenBSD be the active
partition at least until the install has been completed.
- Next the disk label which defines the layout of the OpenBSD file
- systems must be set up. The installation script will invoke an
- editor allowing you to do this. Note that partition 'c' inside
- this disk label should ALWAYS reflect the entire disk, including
- any non-OpenBSD portions. The root file system should be in
- partition 'a', and swap is usually in partition 'b'. If you have
- DOS or Linux partitions defined on the disk, these will usually
- show up as partition 'h', 'i' and so on. It is recommended that
- you create separate partitions for /usr and /var, and if you have
- room for it, also for /home. Currently OpenBSD will not share a
- disk with any other operating system care should be taken not to
- overwrite any data on other disks in the system and that no data
- is on the disk to be used for OpenBSD/MACHINE.
+OpenBSDInstallPart4({:-If you have DOS or Linux
+ partitions defined on the disk, these will usually show up as
+ partition 'h', 'i' and so on.
+
+ Currently OpenBSD will not share a disk with any other operating
+ system, so care should be taken not to overwrite any data on other
+ disks in the system and that no data is on the disk to be used
+ for OpenBSD/MACHINE.
Note that all OpenBSD partitions in the disk label must have an
offset that makes it start within the OpenBSD part of the disk,
and a size that keeps it inside of that portion of the disk. This
- is within the bounds of the 'c' partition.
-
- The swap partition (usually 'b') should have a type of "swap", all
- other native OpenBSD partitions should have a type of "4.2BSD".
- Block and fragment sizes are usually 8192 and 1024 bytes, but can
- also be 4096 and 512 or even 16384 and 2048 bytes.
-
- The install program will now label your disk and ask which file
- systems should be created on which partitions. It will auto-
- matically select the 'a' partition to be the root file system.
- Next it will ask for which disk and partition you want a file
- system created on. This will be the same as the disk name (e.g.
- "sd0") with the letter identifying the partition (e.g. "d")
- appended (e.g. "sd0d"). Then it will ask where this partition is
- to be mounted, e.g. /usr. This process will be repeated until
- you just hit return.
-
- At this point you will be asked to confirm that the file system
- information you have entered is correct, and given an opportunity
- to change the file system table. Next it will create the new file
- systems as specified, OVERWRITING ANY EXISTING DATA. This is the
- point of no return.
-
- After all your file systems have been created, the install program
- will give you an opportunity to configure the network. The network
- configuration you enter (if any) can then be used to do the install
- from another system using HTTP or FTP, and will also be the
- configuration used by the system after the installation is complete.
-
- If you select to configure the network, the install program will
- ask you for a name of your system and the DNS domain name to use.
- Note that the host name should be without the domain part, and that
- the domain name should NOT {:-include-:} the host name part.
-
- Next the system will give you a list of network interfaces you can
- configure. For each network interface you select to configure, it
- will ask for the IP address to use, the symbolic host name to use,
- the netmask to use and any interface-specific flags to set. The
- interface-specific flags are usually used to determine which media
- the network card is to use. Supply the appropriate media options
- as suggested, Typically no media flags are required as autodetect
- normally works.
-
- After all network interfaces has been configured the install pro-
- gram will ask for a default route and IP address of the primary
- name server to use. You will also be presented with an opportunity
- to edit the host table.
-
- At this point you will be allowed to edit the file system table
- that will be used for the remainder of the installation and that
- will be used by the finished system, following which the new file
- systems will be mounted to complete the installation.
-
- After these preparatory steps have been completed, you will be
- able to extract the distribution sets onto your system. There
- are several install methods supported; FTP, HTTP, tape, CD-ROM
- or a local disk partition.
+ is within the bounds of the 'c' partition.-:})
+
+OpenBSDInstallPart5(sd0)
+
+OpenBSDInstallNet
+
+OpenBSDInstallNet2({:-CD-ROM, -:})
OpenBSDFTPInstall