diff options
Diffstat (limited to 'distrib/notes')
| -rw-r--r-- | distrib/notes/zaurus/install | 83 |
1 files changed, 78 insertions, 5 deletions
diff --git a/distrib/notes/zaurus/install b/distrib/notes/zaurus/install index a2add24bdaf..bf64ab066cc 100644 --- a/distrib/notes/zaurus/install +++ b/distrib/notes/zaurus/install @@ -1,4 +1,4 @@ -dnl $OpenBSD: install,v 1.4 2005/01/15 17:52:09 miod Exp $ +dnl $OpenBSD: install,v 1.5 2005/01/16 01:46:56 deraadt Exp $ OpenBSDInstallPrelude OpenBSD is installed on the Zaurus by effectively converting @@ -50,11 +50,21 @@ OpenBSDInstallPart4({:- If you have Linux partitions defined on the disk, these will usually show up as partition 'h', 'i' and so on.-:}) -dnl Change this after fdisk swap command is added. One of the three partitions on the Zaurus C3000 hard drive is - a 3GB MSDOS filesystem. It is recommended that you use fdisk - to convert this Zaurus partition to an OpenBSD partition by - changing the partition ID to 'A5'. + a 3GB MSDOS filesystem. This partition can be a lot smaller, + it is therefore recommended that you cut most of the space off + this tiny MSDOS partition, and create a new 0xA5 partition + afterwards, like this: + + 0: 83 0 3 13 - 1511 7 17 [ 63: 205569 ] Linux files* + 1: 83 1512 0 1 - 7559 7 17 [ 205632: 822528 ] Linux files* + 2: 0C 7560 0 1 - 9065 7 1 [ 1028160: 204800 ] Win95 FAT32L + 3: A6 9065 7 2 - 67885 5 3 [ 1232960: 7999488 ] OpenBSD + + After shrinking the MSDOS partition, please be sure to newfs it + using: + + newfs -t msdos /dev/rwd0k Note that all OpenBSD partitions in the disk label must have an offset that makes it start within the OpenBSD part of the disk, @@ -63,6 +73,69 @@ dnl Change this after fdisk swap command is added. shared with other operating systems, and within the OpenBSD fdisk partition if the disk is being shared. + For purposes of recovery in case Linux becomes inoperable for + one reason or another with HDD1 Errors and such, we detail the + process to come up single user: + + Remove power and the battery. + Begin holding down the 'b' and 'd' keys. + Wait for 1 minute. + Insert battery and power on unit. + As soon as a login screen starts to show up, release the 'b' + and 'd' keys. + Login as root. + + The following sequence is also recommended inside Linux so that + problems will happen less often. By default the boot scripts fail + if the MSDOS partition is corrupt in any way. If you are already + root do the following, which will skip mounting the MSDOS partition. + + Login as root. + + Find the rc.rofilesys file. It is either in + /root/etc/rc.d + + cd /root/home/etc/rc.d + + Or you have to mount it using: + + mount /dev/mtdblock2 /mnt + cd /mnt/home/etc/rc.d + + cat rc.rofilesys | sed -e '/vfat/s/^/#/' > vfat + diff -u rc.rofilesys vfat # to double check + cp rc.rofilesys rc.rofilesys.vfat + cp vfat rc.rofilesys + + In these cases below we avoid using vi because Linux quality is of + such high quality that vi locks up the console. If you logged in + multiuser you may be able to use vi. + + Please be aware that if you fsck the two Linux partitions on + the disk, they are actually ext3fs partitions and you will thereby + corrupt their journals. This will make them into ext2fs partitions. + Linux will not be able to boot, and you will need to use the + processes above to get to the point where Linux will mount them as + ext2fs partitions: + + Login as root. + + Find the rc.rofilesys file. It is either in + /root/etc/rc.d + + cd /root/home/etc/rc.d + + Or you have to mount it using: + + mount /dev/mtdblock2 /mnt + cd /mnt/home/etc/rc.d + + cat rc.rofilesys | sed -e '/^LINUXFMT=ext3$/s/^/#/' \ + -e '/^#LINUXFMT=ext2$/s/^#//' > ext2 + diff -u rc.rofilesys ext2 # to double check + cp rc.rofilesys rc.rofilesys.ext2 + cp ext2 rc.rofilesys + If you have created an 'A5' OpenBSD partition earlier using fdisk, you will be able to use disklabel to cut that partition into at least a root filesystem and swap partition. |