diff options
Diffstat (limited to 'distrib/pmax/install.md')
| -rw-r--r-- | distrib/pmax/install.md | 114 |
1 files changed, 28 insertions, 86 deletions
diff --git a/distrib/pmax/install.md b/distrib/pmax/install.md index a3b1a822893..53c7ebbdbda 100644 --- a/distrib/pmax/install.md +++ b/distrib/pmax/install.md @@ -1,4 +1,4 @@ -# $OpenBSD: install.md,v 1.5 1997/09/30 17:52:46 deraadt Exp $ +# $OpenBSD: install.md,v 1.6 1998/03/27 23:28:15 deraadt Exp $ # $NetBSD: install.md,v 1.3.2.5 1996/08/26 15:45:28 gwr Exp $ # # @@ -80,10 +80,10 @@ md_makerootwritable() { } md_mountkernfs() { - if [ -e ${KERNFSMOUNTED} ] - then - return - fi + if [ -e ${KERNFSMOUNTED} ] + then + return + fi if [ ! -d /kern ]; then mkdir /kern fi @@ -91,14 +91,14 @@ md_mountkernfs() { if [ ! -d /mnt2 ]; then mkdir /mnt2 fi - if ! mount -t kernfs /kern /kern - then - cat << \__kernfs_failed_1 + if ! mount -t kernfs /kern /kern + then + cat << \__kernfs_failed_1 FATAL ERROR: Can't mount kernfs filesystem __kernfs_failed_1 - exit - fi - > ${KERNFSMOUNTED} + exit + fi + > ${KERNFSMOUNTED} } md_machine_arch() { @@ -122,16 +122,16 @@ md_get_ifdevs() { md_get_partition_range() { # return range of valid partition letters - echo "[a-h]" + echo "[a-p]" } md_installboot() { - echo -n "Installing boot block..." - # $1 is the root disk - disklabel -W ${1} - disklabel -B ${1} - echo "done." + echo -n "Installing boot block..." + # $1 is the root disk + disklabel -W ${1} + disklabel -B ${1} + echo "done." # we also use this chance to do an ldconfig here echo -n "creating runtime link editor directory cache..." chroot /mnt ldconfig @@ -188,55 +188,6 @@ md_prep_disklabel() esac # display example - cat << \__md_prep_disklabel_1 - -Here is an example of what the partition information will look like once -you have entered the disklabel editor. Disk partition sizes and offsets -are in sector (most likely 512 bytes) units. - -Make sure these size/offset pairs are on cylinder boundaries (the number -of sector per cylinder is given in the `sectors/cylinder' entry. - -If this disk is previously un-labeled, only the "c" partition will show up -in the editor and you will have to enter lines similar to those shown in the -example for the other paritions. If you are uncertain about the syntax or -space requirements, this is a good time to review the installation notes. - -Do not change any parameters except the partition layout and the label name. -It's probably also wisest not to touch the `8 partitions:' line, even -in case you have defined less than sixteen partitions. - -[** EXAMPLE **] -# /dev/rrz0c: -type: SCSI -disk: SEAGATE ST1480 r -label: -flags: -bytes/sector: 512 -sectors/track: 63 -tracks/cylinder: 11 -sectors/cylinder: 693 -cylinders: 832527 -total sectors: 832527 -rpm: 3600 -interleave: 1 -trackskew: 0 -cylinderskew: 0 -headswitch: 0 # milliseconds -track-to-track seek: 0 # milliseconds -drivedata: 0 - -8 partitions: -# size offset fstype [fsize bsize cpg] - a: 65536 0 4.2BSD 1024 8192 16 # (Cyl. 0 - 94*) - b: 131072 65536 swap # (Cyl. 94*- 283*) - c: 832527 0 unused 1024 8192 # (Cyl. 0 - 1201*) - d: 635919 196608 4.2BSD 1024 8192 16 # (Cyl. 283*- 1201*) -[End of **EXAMPLE**] - -__md_prep_disklabel_1 - echo -n "Press [Enter] to continue " - getresp "" disklabel -W ${_disk} # TTT hack to workaround disklabel problems disklabel ${_disk} > /tmp/tempdisklabel @@ -260,14 +211,11 @@ md_welcome_banner() { echo "Welcome to the OpenBSD/pmax ${VERSION} installation program." cat << \__welcome_banner_1 -This program is designed to help you put OpenBSD on your disk, -in a simple and rational way. You'll be asked several questions, -and it would probably be useful to have your disk's hardware -manual, the installation notes, and a calculator handy. +This program is designed to help you put OpenBSD on your disk in a simple and +rational way. __welcome_banner_1 else - echo "" echo "Welcome to the OpenBSD/pmax ${VERSION} upgrade program." cat << \__welcome_banner_2 @@ -283,26 +231,22 @@ __welcome_banner_2 cat << \__welcome_banner_3 -As with anything which modifies your disk's contents, this -program can cause SIGNIFICANT data loss, and you are advised -to make sure your data is backed up before beginning the -installation process. +As with anything which modifies your disk's contents, this program can +cause SIGNIFICANT data loss, and you are advised to make sure your +data is backed up before beginning the installation process. -Default answers are displayed in brackets after the questions. -You can hit Control-C at any time to quit, but if you do so at a -prompt, you may have to hit return. Also, quitting in the middle of +Default answers are displayed in brackets after the questions. You +can hit Control-C at any time to quit, but if you do so at a prompt, +you may have to hit return. Also, quitting in the middle of installation may leave your system in an inconsistent state. - __welcome_banner_3 } | more } md_not_going_to_install() { cat << \__not_going_to_install_1 - OK, then. Enter `halt' at the prompt to halt the machine. Once the machine has halted, power-cycle the system to load new boot code. - __not_going_to_install_1 } @@ -314,10 +258,8 @@ md_congrats() { what="upgraded"; fi cat << __congratulations_1 - -CONGRATULATIONS! You have successfully $what OpenBSD! -To boot the installed system, enter halt at the command prompt. Once the -system has halted, reset the machine and boot from the disk. - +CONGRATULATIONS! You have successfully $what OpenBSD! To boot the +installed system, enter halt at the command prompt. Once the system +has halted, reset the machine and boot from the disk. __congratulations_1 } |