diff options
Diffstat (limited to 'distrib')
| -rw-r--r-- | distrib/sparc/install.md | 101 |
1 files changed, 40 insertions, 61 deletions
diff --git a/distrib/sparc/install.md b/distrib/sparc/install.md index a9c2907e854..295703aa535 100644 --- a/distrib/sparc/install.md +++ b/distrib/sparc/install.md @@ -1,4 +1,4 @@ -# $OpenBSD: install.md,v 1.14 1997/09/30 17:52:49 deraadt Exp $ +# $OpenBSD: install.md,v 1.15 1997/10/25 09:44:51 todd Exp $ # $NetBSD: install.md,v 1.3.2.5 1996/08/26 15:45:28 gwr Exp $ # # @@ -122,10 +122,28 @@ md_get_partition_range() { } md_installboot() { + local _rawdev + local _prefix + + if [ "X${1}" = X"" ]; then + echo "No disk device specified, you must run installboot manually." + return + fi + _rawdev=/dev/r${1}c + + # use extracted mdec if it exists (may be newer) + if [ -e /mnt/usr/mdec/boot ]; then + _prefix=/mnt/usr/mdec + elif [ -e /usr/mdec/boot ]; then + _prefix=/usr/mdec + else + echo "No boot block prototypes found, you must run installboot manually." + return + fi + echo "Installing boot block..." - cp /usr/mdec/boot /mnt/boot - sync; sync; sync - installboot -v /mnt/boot /usr/mdec/bootxx /dev/r${1}a + cp ${_prefix}/boot /mnt/boot + ${_prefix}/installboot -v /mnt/boot ${_prefix}/bootxx ${_rawdev} } md_native_fstype() { @@ -159,63 +177,24 @@ md_prep_disklabel() md_checkfordisklabel $_disk case $? in 0) - echo -n "Do you wish to edit the disklabel on $_disk? [y]" ;; 1) - echo "WARNING: Disk $_disk has no label" - echo -n "Do you want to create one with the disklabel editor? [y]" + echo "WARNING: Label on disk $_disk has no label. You will be creating a new one." + echo ;; 2) - echo "WARNING: Label on disk $_disk is corrupted" - echo -n "Do you want to try and repair the damage using the disklabel editor? [y]" + echo "WARNING: Label on disk $_disk is corrupted. You will be repairing." + echo ;; esac - getresp "y" - case "$resp" in - y*|Y*) ;; - *) return ;; - esac - # display example cat << \__md_prep_disklabel_1 - -Here is an example of what the partition information will look like once -you have entered the disklabel editor. Disk partition sizes and offsets -are in sector (most likely 512 bytes) units. - -Make sure these size/offset pairs are on cylinder boundaries (the number -of sector per cylinder is given in the `sectors/cylinder' entry. - -If this disk is previously un-labeled, only the "c" partition will show up -in the editor and you will have to enter lines similar to those shown in the -example for the other paritions. If you are uncertain about the syntax or -space requirements, this is a good time to review the installation notes. - -Do not change any parameters except the partition layout and the label name. -It's probably also wisest not to touch the `16 partitions:' line, even -in case you have defined less than sixteen partitions. - -[** EXAMPLE **] -disk: p4200s -bytes/sector: 512 -sectors/track: 40 -tracks/cylinder: 8 -sectors/cylinder: 320 -cylinders: 1280 -total sectors: 409600 - -16 partitions: -# size offset fstype [fsize bsize cpg] - a: 51200 0 4.2BSD 1024 8192 16 # (Cyl. 0 - 159) - b: 51200 51200 swap # (Cyl. 160 - 319) - c: 409600 0 unused 0 0 # (Cyl. 0 - 1279) - d: 307200 102400 4.2BSD 1024 8192 16 # (Cyl. 320 - 1279) -[End of **EXAMPLE**] +If you are unsure of how to use multiple partitions properly +(ie. seperating /, /usr, /tmp, /var, /usr/local, and other things) +just split the space into a root and swap partition for now. __md_prep_disklabel_1 - echo -n "Press [Enter] to continue " - getresp "" disklabel -W ${_disk} disklabel -E ${_disk} } @@ -235,10 +214,10 @@ md_welcome_banner() { echo "Welcome to the OpenBSD/sparc ${VERSION} installation program." cat << \__welcome_banner_1 -This program is designed to help you put OpenBSD on your disk, -in a simple and rational way. You'll be asked several questions, -and it would probably be useful to have your disk's hardware -manual, the installation notes, and a calculator handy. +This program is designed to help you put OpenBSD on your disk, in a +simple and rational way. You'll be asked several questions, and it +would probably be useful to have your disk's hardware manual, the +installation notes, and a calculator handy. __welcome_banner_1 else @@ -253,19 +232,19 @@ As a reminder, installing the `etc' binary set is NOT recommended. Once the rest of your system has been upgraded, you should manually merge any changes to files in the `etc' set into those files which already exist on your system. + __welcome_banner_2 fi cat << \__welcome_banner_3 -As with anything which modifies your disk's contents, this -program can cause SIGNIFICANT data loss, and you are advised -to make sure your data is backed up before beginning the -installation process. +As with anything which modifies your disk's contents, this program can +cause SIGNIFICANT data loss, and you are advised to make sure your +data is backed up before beginning the installation process. -Default answers are displayed in brackets after the questions. -You can hit Control-C at any time to quit, but if you do so at a -prompt, you may have to hit return. Also, quitting in the middle of +Default answers are displayed in brackets after the questions. You +can hit Control-C at any time to quit, but if you do so at a prompt, +you may have to hit return. Also, quitting in the middle of installation may leave your system in an inconsistent state. __welcome_banner_3 |