diff options
Diffstat (limited to 'sbin/mount_nfs/mount_nfs.8')
-rw-r--r-- | sbin/mount_nfs/mount_nfs.8 | 38 |
1 files changed, 19 insertions, 19 deletions
diff --git a/sbin/mount_nfs/mount_nfs.8 b/sbin/mount_nfs/mount_nfs.8 index 5e06f4e6e95..2c88aabe99d 100644 --- a/sbin/mount_nfs/mount_nfs.8 +++ b/sbin/mount_nfs/mount_nfs.8 @@ -1,4 +1,4 @@ -.\" $OpenBSD: mount_nfs.8,v 1.34 2005/06/23 00:41:56 jaredy Exp $ +.\" $OpenBSD: mount_nfs.8,v 1.35 2005/06/29 20:48:05 jaredy Exp $ .\" $NetBSD: mount_nfs.8,v 1.3 1996/02/18 11:59:10 fvdl Exp $ .\" .\" Copyright (c) 1992, 1993, 1994, 1995 @@ -74,24 +74,6 @@ Use the NFS Version 2 protocol. Use the NFS Version 3 protocol. The default is to try version 3 first, and fall back to version 2 if the mount fails. -.It Fl I Ar readdirsize -Set the readdir read size to the specified value. -The value should normally be a multiple of -.Dv DIRBLKSIZ -that is less than or equal to the read size for the mount. -.It Fl R Ar retrycnt -Set the retry count for doing the mount to the specified value. -The default is 10000. -.It Fl T -Use TCP instead of UDP. -This is recommended for servers that are not on the same LAN cable as -the client. -(NB: This is NOT supported by most non-BSD servers.) -.It Fl U -Force the mount protocol to use UDP, even for TCP NFS mounts. -(Necessary for some old -.Bx -servers.) .It Fl a Ar maxreadahead Set the read-ahead count to the specified value. This may be in the range of 0\-4, and determines how many blocks @@ -124,6 +106,11 @@ This should be used for mounts on old servers that cannot handle a group list size of 16, as specified in RFC 1057. Try 8, if users in a lot of groups cannot get a response from the mount point. +.It Fl I Ar readdirsize +Set the readdir read size to the specified value. +The value should normally be a multiple of +.Dv DIRBLKSIZ +that is less than or equal to the read size for the mount. .It Fl i Make the mount interruptible, which implies that file system calls that are delayed due to an unresponsive server will fail with EINTR when a @@ -180,6 +167,9 @@ The default is 5 seconds. Use the specified port number for NFS requests. The default is to query the portmapper for the NFS port. .El +.It Fl R Ar retrycnt +Set the retry count for doing the mount to the specified value. +The default is 10000. .It Fl r Ar readsize Set the read data size to the specified value. It should normally be a power of 2 greater than or equal to 1024. @@ -201,6 +191,11 @@ after .Ar retrans round trip timeout intervals have been reached (see .Fl x ) . +.It Fl T +Use TCP instead of UDP. +This is recommended for servers that are not on the same LAN cable as +the client. +(NB: This is NOT supported by most non-BSD servers.) .It Fl t Ar timeout Set the initial retransmit timeout to the specified value. May be useful for fine tuning UDP mounts over internetworks @@ -214,6 +209,11 @@ value if there is a low retransmit rate but long response delay observed. option should be specified when using this option to manually tune the timeout interval.) +.It Fl U +Force the mount protocol to use UDP, even for TCP NFS mounts. +(Necessary for some old +.Bx +servers.) .It Fl w Ar writesize Set the write data size to the specified value. Ditto the comments w.r.t. the |