diff options
Diffstat (limited to 'share')
| -rw-r--r-- | share/man/man4/bge.4 | 26 | ||||
| -rw-r--r-- | share/man/man4/nge.4 | 26 |
2 files changed, 18 insertions, 34 deletions
diff --git a/share/man/man4/bge.4 b/share/man/man4/bge.4 index ab5fdb74acb..0365c63522b 100644 --- a/share/man/man4/bge.4 +++ b/share/man/man4/bge.4 @@ -1,4 +1,4 @@ -.\" $OpenBSD: bge.4,v 1.37 2008/05/31 23:42:48 brad Exp $ +.\" $OpenBSD: bge.4,v 1.38 2008/07/26 00:51:38 brad Exp $ .\" Copyright (c) 2001 Wind River Systems .\" Copyright (c) 1997, 1998, 1999, 2000, 2001 .\" Bill Paul <wpaul@windriver.com>. All rights reserved. @@ -30,7 +30,7 @@ .\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF .\" THE POSSIBILITY OF SUCH DAMAGE. .\" -.Dd $Mdocdate: May 31 2008 $ +.Dd $Mdocdate: July 26 2008 $ .Dt BGE 4 .Os .Sh NAME @@ -110,26 +110,16 @@ SysKonnect SK-9D21 (10/100/1000baseT) SysKonnect SK-9D41 (1000baseSX) .El .Pp -All of these NICs are capable of 10, 100 speeds over CAT5 copper cable; -the Gigabit controller chips also support 1000Mbps, except for the -SysKonnect SK-9D41 which supports only 1000Mbps over multimode fiber. -It has two R4000 CPU cores and is PCI v2.2 and PCI-X v1.0 compliant. -It supports +The +.Nm +driver supports .\"IP, TCP .\"and UDP checksum offload for both receive and transmit, VLAN tag insertion as well as a 256-bit multicast hash filter. -Additional features may be provided via value-add firmware updates. -The BCM57xx supports TBI (ten bit interface) and GMII transceivers, which -means it can be used with either copper or 1000baseX fiber applications. -Note however the device only supports a single speed in TBI mode. -.Pp -Most BCM5700-based cards also use the Broadcom BCM5401 or BCM5411 10/100/1000 -copper Gigabit transceivers, -which support autonegotiation of 10, 100 and 1000Mbps modes in -full or half duplex. .Pp -The BCM5700, BCM5701, BCM5703 and BCM5704 are capable of supporting Jumbo frames, -which can be configured via the interface MTU setting. +The BCM5700, BCM5701, BCM5703 and BCM5704 chips are capable of +supporting Jumbo frames, which can be configured via the +interface MTU setting. Selecting an MTU larger than 1500 bytes with the .Xr ifconfig 8 utility configures the adapter to receive and transmit Jumbo frames. diff --git a/share/man/man4/nge.4 b/share/man/man4/nge.4 index df26162942b..639e0b30c05 100644 --- a/share/man/man4/nge.4 +++ b/share/man/man4/nge.4 @@ -1,4 +1,4 @@ -.\" $OpenBSD: nge.4,v 1.31 2008/04/03 07:07:22 jmc Exp $ +.\" $OpenBSD: nge.4,v 1.32 2008/07/26 00:51:38 brad Exp $ .\" Copyright (c) 2001 Wind River Systems .\" Copyright (c) 1997, 1998, 1999, 2000, 2001 .\" Bill Paul <wpaul@bsdi.com>. All rights reserved. @@ -32,7 +32,7 @@ .\" .\" $FreeBSD: nge.4,v 1.11 2002/08/08 18:30:39 ambrisko Exp $ .\" -.Dd $Mdocdate: April 3 2008 $ +.Dd $Mdocdate: July 26 2008 $ .Dt NGE 4 .Os .Sh NAME @@ -71,21 +71,15 @@ Surecom Technology EP-320G-TX TRENDnet TEG-PCITX (32-bit PCI) and TEG-PCITX2 (64-bit PCI) .El .Pp -All of these NICs are capable of 10, 100 and 1000Mbps speeds over CAT5 -copper cable. -The DP83820 supports TBI (ten bit interface) and GMII -transceivers, which means it can be used with either copper or 1000baseX -fiber applications. -The DP83820 supports IPv4 receive IP/TCP/UDP checksum offload -as well as a 2048-bit multicast hash filter and up to 4 pattern match -buffers. -.Pp -Most cards also use the DP83861 10/100/1000 copper Gigabit transceiver -chip, which supports autonegotiation of 10, 100 and 1000Mbps modes in -full or half duplex. +The +.Nm +driver supports IPv4 receive IP/TCP/UDP checksum offload as well as +a 2048-bit multicast hash filter and up to 4 pattern match buffers. .Pp -The DP83820 also supports Jumbo frames, which can be configured -via the interface MTU setting. +The +.Nm +driver also supports Jumbo frames, which can be configured via the +interface MTU setting. Selecting an MTU larger than 1500 bytes with the .Xr ifconfig 8 utility configures the adapter to receive and transmit Jumbo frames. |