diff options
Diffstat (limited to 'sys/dev/pci/ixgbe_82598.c')
| -rw-r--r-- | sys/dev/pci/ixgbe_82598.c | 1116 |
1 files changed, 1116 insertions, 0 deletions
diff --git a/sys/dev/pci/ixgbe_82598.c b/sys/dev/pci/ixgbe_82598.c new file mode 100644 index 00000000000..58e38a27cc1 --- /dev/null +++ b/sys/dev/pci/ixgbe_82598.c @@ -0,0 +1,1116 @@ +/* $OpenBSD: ixgbe_82598.c,v 1.1 2008/06/08 20:01:02 reyk Exp $ */ + +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD: src/sys/dev/ixgbe/ixgbe_82598.c,v 1.4 2008/05/16 18:46:30 jfv Exp $*/ + +#include <dev/pci/ixgbe.h> +#include <dev/pci/ixgbe_type.h> + +s32 ixgbe_init_ops_82598(struct ixgbe_hw *hw); +s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw, + ixgbe_link_speed *speed, + bool *autoneg); +s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw, + ixgbe_link_speed *speed, + bool *autoneg); +enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw); +s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num); +s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw); +s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw, + ixgbe_link_speed *speed, + bool *link_up, bool link_up_wait_to_complete); +s32 ixgbe_setup_mac_link_speed_82598(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg, + bool autoneg_wait_to_complete); +s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw); +s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg, + bool autoneg_wait_to_complete); +#ifndef NO_82598_A0_SUPPORT +s32 ixgbe_reset_hw_rev_0_82598(struct ixgbe_hw *hw); +#endif +s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw); +s32 ixgbe_configure_fiber_serdes_fc_82598(struct ixgbe_hw *hw); +s32 ixgbe_setup_fiber_serdes_link_82598(struct ixgbe_hw *hw); +s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq); +s32 ixgbe_blink_led_stop_82598(struct ixgbe_hw *hw, u32 index); +s32 ixgbe_blink_led_start_82598(struct ixgbe_hw *hw, u32 index); + +/** + * ixgbe_init_ops_82598 - Inits func ptrs and MAC type + * @hw: pointer to hardware structure + * + * Initialize the function pointers and assign the MAC type for 82598. + * Does not touch the hardware. + **/ +s32 ixgbe_init_ops_82598(struct ixgbe_hw *hw) +{ + struct ixgbe_mac_info *mac = &hw->mac; + struct ixgbe_phy_info *phy = &hw->phy; + s32 ret_val; + + ret_val = ixgbe_init_phy_ops_generic(hw); + ret_val = ixgbe_init_ops_generic(hw); + + /* MAC */ +#ifndef NO_82598_A0_SUPPORT + if (hw->revision_id == 0) + mac->ops.reset_hw = &ixgbe_reset_hw_rev_0_82598; + else + mac->ops.reset_hw = &ixgbe_reset_hw_82598; +#else + mac->ops.reset_hw = &ixgbe_reset_hw_82598; +#endif + mac->ops.get_media_type = &ixgbe_get_media_type_82598; + + /* LEDs */ + mac->ops.blink_led_start = &ixgbe_blink_led_start_82598; + mac->ops.blink_led_stop = &ixgbe_blink_led_stop_82598; + + /* RAR, Multicast, VLAN */ + mac->ops.set_vmdq = &ixgbe_set_vmdq_82598; + + /* Flow Control */ + mac->ops.setup_fc = &ixgbe_setup_fc_82598; + + /* Call PHY identify routine to get the phy type */ + phy->ops.identify(hw); + + /* PHY Init */ + switch (hw->phy.type) { + case ixgbe_phy_tn: + phy->ops.check_link = &ixgbe_check_phy_link_tnx; + phy->ops.get_firmware_version = + &ixgbe_get_phy_firmware_version_tnx; + break; + case ixgbe_phy_nl: + phy->ops.reset = &ixgbe_reset_phy_nl; + break; + default: + break; + } + + /* Link */ + mac->ops.check_link = &ixgbe_check_mac_link_82598; + if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) { + mac->ops.setup_link = &ixgbe_setup_copper_link_82598; + mac->ops.setup_link_speed = + &ixgbe_setup_copper_link_speed_82598; + mac->ops.get_link_capabilities = + &ixgbe_get_copper_link_capabilities_82598; + } else { + mac->ops.setup_link = &ixgbe_setup_mac_link_82598; + mac->ops.setup_link_speed = &ixgbe_setup_mac_link_speed_82598; + mac->ops.get_link_capabilities = + &ixgbe_get_link_capabilities_82598; + } + + mac->mcft_size = 128; + mac->vft_size = 128; + mac->num_rar_entries = 16; + mac->max_tx_queues = 32; + mac->max_rx_queues = 64; + + return IXGBE_SUCCESS; +} + +/** + * ixgbe_get_link_capabilities_82598 - Determines link capabilities + * @hw: pointer to hardware structure + * @speed: pointer to link speed + * @autoneg: boolean auto-negotiation value + * + * Determines the link capabilities by reading the AUTOC register. + **/ +s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw, + ixgbe_link_speed *speed, + bool *autoneg) +{ + s32 status = IXGBE_SUCCESS; + s32 autoc_reg; + + autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + + if (hw->mac.link_settings_loaded) { + autoc_reg &= ~IXGBE_AUTOC_LMS_ATTACH_TYPE; + autoc_reg &= ~IXGBE_AUTOC_LMS_MASK; + autoc_reg |= hw->mac.link_attach_type; + autoc_reg |= hw->mac.link_mode_select; + } + + switch (autoc_reg & IXGBE_AUTOC_LMS_MASK) { + case IXGBE_AUTOC_LMS_1G_LINK_NO_AN: + *speed = IXGBE_LINK_SPEED_1GB_FULL; + *autoneg = FALSE; + break; + + case IXGBE_AUTOC_LMS_10G_LINK_NO_AN: + *speed = IXGBE_LINK_SPEED_10GB_FULL; + *autoneg = FALSE; + break; + + case IXGBE_AUTOC_LMS_1G_AN: + *speed = IXGBE_LINK_SPEED_1GB_FULL; + *autoneg = TRUE; + break; + + case IXGBE_AUTOC_LMS_KX4_AN: + case IXGBE_AUTOC_LMS_KX4_AN_1G_AN: + *speed = IXGBE_LINK_SPEED_UNKNOWN; + if (autoc_reg & IXGBE_AUTOC_KX4_SUPP) + *speed |= IXGBE_LINK_SPEED_10GB_FULL; + if (autoc_reg & IXGBE_AUTOC_KX_SUPP) + *speed |= IXGBE_LINK_SPEED_1GB_FULL; + *autoneg = TRUE; + break; + + default: + status = IXGBE_ERR_LINK_SETUP; + break; + } + + return status; +} + +/** + * ixgbe_get_copper_link_capabilities_82598 - Determines link capabilities + * @hw: pointer to hardware structure + * @speed: pointer to link speed + * @autoneg: boolean auto-negotiation value + * + * Determines the link capabilities by reading the AUTOC register. + **/ +s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw, + ixgbe_link_speed *speed, + bool *autoneg) +{ + s32 status = IXGBE_ERR_LINK_SETUP; + u16 speed_ability; + + *speed = 0; + *autoneg = TRUE; + + status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_SPEED_ABILITY, + IXGBE_MDIO_PMA_PMD_DEV_TYPE, + &speed_ability); + + if (status == IXGBE_SUCCESS) { + if (speed_ability & IXGBE_MDIO_PHY_SPEED_10G) + *speed |= IXGBE_LINK_SPEED_10GB_FULL; + if (speed_ability & IXGBE_MDIO_PHY_SPEED_1G) + *speed |= IXGBE_LINK_SPEED_1GB_FULL; + } + + return status; +} + +/** + * ixgbe_get_media_type_82598 - Determines media type + * @hw: pointer to hardware structure + * + * Returns the media type (fiber, copper, backplane) + **/ +enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw) +{ + enum ixgbe_media_type media_type; + + /* Media type for I82598 is based on device ID */ + switch (hw->device_id) { + case IXGBE_DEV_ID_82598AF_DUAL_PORT: + case IXGBE_DEV_ID_82598AF_SINGLE_PORT: + case IXGBE_DEV_ID_82598EB_CX4: + case IXGBE_DEV_ID_82598_CX4_DUAL_PORT: + case IXGBE_DEV_ID_82598_DA_DUAL_PORT: + case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM: + case IXGBE_DEV_ID_82598EB_XF_LR: + media_type = ixgbe_media_type_fiber; + break; + case IXGBE_DEV_ID_82598AT: + media_type = ixgbe_media_type_copper; + break; + case IXGBE_DEV_ID_82598AT_DUAL_PORT: + media_type = ixgbe_media_type_copper; + break; + default: + media_type = ixgbe_media_type_unknown; + break; + } + + return media_type; +} + +/** + * ixgbe_setup_fc_82598 - Configure flow control settings + * @hw: pointer to hardware structure + * @packetbuf_num: packet buffer number (0-7) + * + * Configures the flow control settings based on SW configuration. This + * function is used for 802.3x flow control configuration only. + **/ +s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num) +{ + u32 frctl_reg; + u32 rmcs_reg; + + if (packetbuf_num < 0 || packetbuf_num > 7) { + DEBUGOUT1("Invalid packet buffer number [%d], expected range is" + " 0-7\n", packetbuf_num); + ASSERT(0); + } + + frctl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL); + frctl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE); + + rmcs_reg = IXGBE_READ_REG(hw, IXGBE_RMCS); + rmcs_reg &= ~(IXGBE_RMCS_TFCE_PRIORITY | IXGBE_RMCS_TFCE_802_3X); + + /* + * 10 gig parts do not have a word in the EEPROM to determine the + * default flow control setting, so we explicitly set it to full. + */ + if (hw->fc.type == ixgbe_fc_default) + hw->fc.type = ixgbe_fc_full; + + /* + * We want to save off the original Flow Control configuration just in + * case we get disconnected and then reconnected into a different hub + * or switch with different Flow Control capabilities. + */ + hw->fc.original_type = hw->fc.type; + + /* + * The possible values of the "flow_control" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames but not + * send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but we do not + * support receiving pause frames) + * 3: Both Rx and Tx flow control (symmetric) are enabled. + * other: Invalid. + */ + switch (hw->fc.type) { + case ixgbe_fc_none: + break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled, + * and Tx Flow control is disabled. + */ + frctl_reg |= IXGBE_FCTRL_RFCE; + break; + case ixgbe_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is disabled, + * by a software over-ride. + */ + rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; + break; + case ixgbe_fc_full: + /* + * Flow control (both Rx and Tx) is enabled by a software + * over-ride. + */ + frctl_reg |= IXGBE_FCTRL_RFCE; + rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; + break; + default: + /* We should never get here. The value should be 0-3. */ + DEBUGOUT("Flow control param set incorrectly\n"); + ASSERT(0); + break; + } + + /* Enable 802.3x based flow control settings. */ + IXGBE_WRITE_REG(hw, IXGBE_FCTRL, frctl_reg); + IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg); + + /* + * Check for invalid software configuration, zeros are completely + * invalid for all parameters used past this point, and if we enable + * flow control with zero water marks, we blast flow control packets. + */ + if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) { + DEBUGOUT("Flow control structure initialized incorrectly\n"); + return IXGBE_ERR_INVALID_LINK_SETTINGS; + } + + /* + * We need to set up the Receive Threshold high and low water + * marks as well as (optionally) enabling the transmission of + * XON frames. + */ + if (hw->fc.type & ixgbe_fc_tx_pause) { + if (hw->fc.send_xon) { + IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), + (hw->fc.low_water | IXGBE_FCRTL_XONE)); + } else { + IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), + hw->fc.low_water); + } + IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), + (hw->fc.high_water)|IXGBE_FCRTH_FCEN); + } + + IXGBE_WRITE_REG(hw, IXGBE_FCTTV(0), hw->fc.pause_time); + IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1)); + + return IXGBE_SUCCESS; +} + +/** + * ixgbe_setup_mac_link_82598 - Configures MAC link settings + * @hw: pointer to hardware structure + * + * Configures link settings based on values in the ixgbe_hw struct. + * Restarts the link. Performs autonegotiation if needed. + **/ +s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw) +{ + ixgbe_link_speed speed; + bool link_up; + u32 autoc_reg; + u32 links_reg; + u32 i; + s32 status = IXGBE_SUCCESS; + + autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + + if (hw->mac.link_settings_loaded) { + autoc_reg &= ~IXGBE_AUTOC_LMS_ATTACH_TYPE; + autoc_reg &= ~IXGBE_AUTOC_LMS_MASK; + autoc_reg |= hw->mac.link_attach_type; + autoc_reg |= hw->mac.link_mode_select; + + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); + IXGBE_WRITE_FLUSH(hw); + msec_delay(50); + } + + /* Restart link */ + autoc_reg |= IXGBE_AUTOC_AN_RESTART; + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); + + /* Only poll for autoneg to complete if specified to do so */ + if (hw->phy.autoneg_wait_to_complete) { + if (hw->mac.link_mode_select == IXGBE_AUTOC_LMS_KX4_AN || + hw->mac.link_mode_select == IXGBE_AUTOC_LMS_KX4_AN_1G_AN) { + links_reg = 0; /* Just in case Autoneg time = 0 */ + for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) { + links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); + if (links_reg & IXGBE_LINKS_KX_AN_COMP) + break; + msec_delay(100); + } + if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) { + status = IXGBE_ERR_AUTONEG_NOT_COMPLETE; + DEBUGOUT("Autonegotiation did not complete.\n"); + } + } + } + + /* + * We want to save off the original Flow Control configuration just in + * case we get disconnected and then reconnected into a different hub + * or switch with different Flow Control capabilities. + */ + hw->fc.original_type = hw->fc.type; + /* + * Set up the SerDes link if in 1Gb mode, otherwise just set up + * 10Gb flow control. + */ + hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); + if (speed == IXGBE_LINK_SPEED_1GB_FULL) + status = ixgbe_setup_fiber_serdes_link_82598(hw); + else + ixgbe_setup_fc_82598(hw, 0); + + /* Add delay to filter out noises during initial link setup */ + msec_delay(50); + + return status; +} + +/** + * ixgbe_check_mac_link_82598 - Get link/speed status + * @hw: pointer to hardware structure + * @speed: pointer to link speed + * @link_up: TRUE is link is up, FALSE otherwise + * @link_up_wait_to_complete: bool used to wait for link up or not + * + * Reads the links register to determine if link is up and the current speed + **/ +s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw, ixgbe_link_speed *speed, + bool *link_up, bool link_up_wait_to_complete) +{ + u32 links_reg; + u32 i; + u16 link_reg, adapt_comp_reg; + + if (hw->phy.type == ixgbe_phy_nl) { + hw->phy.ops.read_reg(hw, 1, IXGBE_TWINAX_DEV, &link_reg); + hw->phy.ops.read_reg(hw, 1, IXGBE_TWINAX_DEV, &link_reg); + hw->phy.ops.read_reg(hw, 0xC00C, IXGBE_TWINAX_DEV, + &adapt_comp_reg); + if (link_up_wait_to_complete) { + for (i = 0; i < IXGBE_LINK_UP_TIME; i++) { + if ((link_reg & (1 << 2)) && + ((adapt_comp_reg & 1) == 0)) { + *link_up = TRUE; + break; + } else { + *link_up = FALSE; + } + msec_delay(100); + hw->phy.ops.read_reg(hw, 1, IXGBE_TWINAX_DEV, + &link_reg); + hw->phy.ops.read_reg(hw, 0xC00C, + IXGBE_TWINAX_DEV, + &adapt_comp_reg); + } + } else { + if ((link_reg & (1 << 2)) && + ((adapt_comp_reg & 1) == 0)) + *link_up = TRUE; + else + *link_up = FALSE; + } + + if (*link_up == FALSE) + goto out; + } + + links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); + if (link_up_wait_to_complete) { + for (i = 0; i < IXGBE_LINK_UP_TIME; i++) { + if (links_reg & IXGBE_LINKS_UP) { + *link_up = TRUE; + break; + } else { + *link_up = FALSE; + } + msec_delay(100); + links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); + } + } else { + if (links_reg & IXGBE_LINKS_UP) + *link_up = TRUE; + else + *link_up = FALSE; + } + + if (links_reg & IXGBE_LINKS_SPEED) + *speed = IXGBE_LINK_SPEED_10GB_FULL; + else + *speed = IXGBE_LINK_SPEED_1GB_FULL; + +out: + return IXGBE_SUCCESS; +} + +/** + * ixgbe_configure_fiber_serdes_fc_82598 - Configure fiber flow control + * @hw: pointer to hardware structure + * + * Reads PCS registers and sets flow control settings, based on + * link-partner's abilities. + **/ +s32 ixgbe_configure_fiber_serdes_fc_82598(struct ixgbe_hw *hw) +{ + s32 ret_val = IXGBE_SUCCESS; + u32 pcs_anadv_reg, pcs_lpab_reg, pcs_lstat_reg, i; + DEBUGFUNC("ixgbe_configure_fiber_serdes_fc_82598"); + + /* Check that autonegotiation has completed */ + for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) { + msec_delay(10); + pcs_lstat_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); + if (pcs_lstat_reg & IXGBE_PCS1GLSTA_LINK_OK) { + if (pcs_lstat_reg & IXGBE_PCS1GLSTA_AN_COMPLETE) { + if (!(pcs_lstat_reg & + (IXGBE_PCS1GLSTA_AN_TIMED_OUT))) + hw->mac.autoneg_failed = 0; + else + hw->mac.autoneg_failed = 1; + break; + } else { + hw->mac.autoneg_failed = 1; + break; + } + } + } + + if (hw->mac.autoneg_failed) { + /* + * AutoNeg failed to achieve a link, so we will turn + * flow control off. + */ + hw->fc.type = ixgbe_fc_none; + DEBUGOUT("Flow Control = NONE.\n"); + ret_val = ixgbe_setup_fc_82598(hw, 0); + goto out; + } + + /* + * Read the AN advertisement and LP ability registers and resolve + * local flow control settings accordingly + */ + pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); + if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) { + /* + * Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.original_type == ixgbe_fc_full) { + hw->fc.type = ixgbe_fc_full; + DEBUGOUT("Flow Control = FULL.\n"); + } else { + hw->fc.type = ixgbe_fc_rx_pause; + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); + } + } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { + hw->fc.type = ixgbe_fc_tx_pause; + DEBUGOUT("Flow Control = TX PAUSE frames only.\n"); + } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && + !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { + hw->fc.type = ixgbe_fc_rx_pause; + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); + } else { + hw->fc.type = ixgbe_fc_none; + DEBUGOUT("Flow Control = NONE.\n"); + } + + ret_val = ixgbe_setup_fc_82598(hw, 0); + if (ret_val) { + DEBUGOUT("Error forcing flow control settings\n"); + goto out; + } + +out: + return ret_val; +} + +/** + * ixgbe_setup_fiber_serdes_link_82598 - Configure fiber serdes link + * @hw: pointer to hardware structure + * + * Sets up PCS registers and sets flow control settings, based on + * link-partner's abilities. + **/ +s32 ixgbe_setup_fiber_serdes_link_82598(struct ixgbe_hw *hw) +{ + u32 reg; + s32 ret_val; + + DEBUGFUNC("ixgbe_setup_fiber_serdes_link_82598"); + + /* + * 10 gig parts do not have a word in the EEPROM to determine the + * default flow control setting, so we explicitly set it to full. + */ + if (hw->fc.type == ixgbe_fc_default) + hw->fc.type = ixgbe_fc_full; + + /* + * 82598 fiber/serdes devices require that flow control be resolved in + * software. + */ + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + + /* + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but + * we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. + */ + switch (hw->fc.type) { + case ixgbe_fc_none: + /* + * Flow control completely disabled by a software + * over-ride. + */ + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is + * disabled by a software over-ride. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + case ixgbe_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is + * disabled, by a software over-ride. + */ + reg |= (IXGBE_PCS1GANA_ASM_PAUSE); + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); + break; + case ixgbe_fc_full: + /* + * Flow control (both Rx and Tx) is enabled by a + * software over-ride. + */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + ret_val = -IXGBE_ERR_CONFIG; + goto out; + break; + } + + IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); + + /* Set PCS register for autoneg */ + /* Enable and restart autoneg */ + reg |= IXGBE_PCS1GLCTL_AN_ENABLE | IXGBE_PCS1GLCTL_AN_RESTART; + + reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; /* Disable AN timeout */ + DEBUGOUT1("Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg); + IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); + + /* + * Configure flow control. If we aren't auto-negotiating, + * just setup the flow control and do not worry about PCS autoneg. + */ + ixgbe_configure_fiber_serdes_fc_82598(hw); + +out: + return IXGBE_SUCCESS; +} + +/** + * ixgbe_setup_mac_link_speed_82598 - Set MAC link speed + * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg: TRUE if auto-negotiation enabled + * @autoneg_wait_to_complete: TRUE if waiting is needed to complete + * + * Set the link speed in the AUTOC register and restarts link. + **/ +s32 ixgbe_setup_mac_link_speed_82598(struct ixgbe_hw *hw, + ixgbe_link_speed speed, bool autoneg, + bool autoneg_wait_to_complete) +{ + s32 status = IXGBE_SUCCESS; + + /* If speed is 10G, then check for CX4 or XAUI. */ + if ((speed == IXGBE_LINK_SPEED_10GB_FULL) && + (!(hw->mac.link_attach_type & IXGBE_AUTOC_10G_KX4))) { + hw->mac.link_mode_select = IXGBE_AUTOC_LMS_10G_LINK_NO_AN; + } else if ((speed == IXGBE_LINK_SPEED_1GB_FULL) && (!autoneg)) { + hw->mac.link_mode_select = IXGBE_AUTOC_LMS_1G_LINK_NO_AN; + } else if (autoneg) { + /* BX mode - Autonegotiate 1G */ + if (!(hw->mac.link_attach_type & IXGBE_AUTOC_1G_PMA_PMD)) + hw->mac.link_mode_select = IXGBE_AUTOC_LMS_1G_AN; + else /* KX/KX4 mode */ + hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN_1G_AN; + } else { + status = IXGBE_ERR_LINK_SETUP; + } + + if (status == IXGBE_SUCCESS) { + hw->phy.autoneg_wait_to_complete = autoneg_wait_to_complete; + + hw->mac.link_settings_loaded = TRUE; + /* + * Setup and restart the link based on the new values in + * ixgbe_hw This will write the AUTOC register based on the new + * stored values + */ + ixgbe_setup_mac_link_82598(hw); + } + + return status; +} + + +/** + * ixgbe_setup_copper_link_82598 - Setup copper link settings + * @hw: pointer to hardware structure + * + * Configures link settings based on values in the ixgbe_hw struct. + * Restarts the link. Performs autonegotiation if needed. Restart + * phy and wait for autonegotiate to finish. Then synchronize the + * MAC and PHY. + **/ +s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw) +{ + s32 status; + + /* Restart autonegotiation on PHY */ + status = hw->phy.ops.setup_link(hw); + + /* Set MAC to KX/KX4 autoneg, which defaults to Parallel detection */ + hw->mac.link_attach_type = (IXGBE_AUTOC_10G_KX4 | IXGBE_AUTOC_1G_KX); + hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN; + + /* Set up MAC */ + ixgbe_setup_mac_link_82598(hw); + + return status; +} + +/** + * ixgbe_setup_copper_link_speed_82598 - Set the PHY autoneg advertised field + * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg: TRUE if autonegotiation enabled + * @autoneg_wait_to_complete: TRUE if waiting is needed to complete + * + * Sets the link speed in the AUTOC register in the MAC and restarts link. + **/ +s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg, + bool autoneg_wait_to_complete) +{ + s32 status; + + /* Setup the PHY according to input speed */ + status = hw->phy.ops.setup_link_speed(hw, speed, autoneg, + autoneg_wait_to_complete); + + /* Set MAC to KX/KX4 autoneg, which defaults to Parallel detection */ + hw->mac.link_attach_type = (IXGBE_AUTOC_10G_KX4 | IXGBE_AUTOC_1G_KX); + hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN; + + /* Set up MAC */ + ixgbe_setup_mac_link_82598(hw); + + return status; +} + +#ifndef NO_82598_A0_SUPPORT +/** + * ixgbe_reset_hw_rev_0_82598 - Performs hardware reset + * @hw: pointer to hardware structure + * + * Resets the hardware by resetting the transmit and receive units, masks and + * clears all interrupts, performing a PHY reset, and performing a link (MAC) + * reset. + **/ +s32 ixgbe_reset_hw_rev_0_82598(struct ixgbe_hw *hw) +{ + s32 status = IXGBE_SUCCESS; + u32 ctrl; + u32 gheccr; + u32 autoc; + u32 i; + u32 resets; + + /* Call adapter stop to disable tx/rx and clear interrupts */ + hw->mac.ops.stop_adapter(hw); + + /* Reset PHY */ + hw->phy.ops.reset(hw); + + for (resets = 0; resets < 10; resets++) { + /* + * Prevent the PCI-E bus from from hanging by disabling PCI-E + * master access and verify no pending requests before reset + */ + if (ixgbe_disable_pcie_master(hw) != IXGBE_SUCCESS) { + status = IXGBE_ERR_MASTER_REQUESTS_PENDING; + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + } + + /* + * Issue global reset to the MAC. This needs to be a SW reset. + * If link reset is used, it might reset the MAC when mng is + * using it. + */ + ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); + IXGBE_WRITE_REG(hw, IXGBE_CTRL, (ctrl | IXGBE_CTRL_RST)); + IXGBE_WRITE_FLUSH(hw); + + /* + * Poll for reset bit to self-clear indicating reset is + * complete + */ + for (i = 0; i < 10; i++) { + usec_delay(1); + ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); + if (!(ctrl & IXGBE_CTRL_RST)) + break; + } + if (ctrl & IXGBE_CTRL_RST) { + status = IXGBE_ERR_RESET_FAILED; + DEBUGOUT("Reset polling failed to complete.\n"); + } + } + + msec_delay(50); + + gheccr = IXGBE_READ_REG(hw, IXGBE_GHECCR); + gheccr &= ~((1 << 21) | (1 << 18) | (1 << 9) | (1 << 6)); + IXGBE_WRITE_REG(hw, IXGBE_GHECCR, gheccr); + + /* + * AUTOC register which stores link settings gets cleared + * and reloaded from EEPROM after reset. We need to restore + * our stored value from init in case SW changed the attach + * type or speed. If this is the first time and link settings + * have not been stored, store default settings from AUTOC. + */ + autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); + if (hw->mac.link_settings_loaded) { + autoc &= ~(IXGBE_AUTOC_LMS_ATTACH_TYPE); + autoc &= ~(IXGBE_AUTOC_LMS_MASK); + autoc |= hw->mac.link_attach_type; + autoc |= hw->mac.link_mode_select; + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc); + } else { + hw->mac.link_attach_type = + (autoc & IXGBE_AUTOC_LMS_ATTACH_TYPE); + hw->mac.link_mode_select = (autoc & IXGBE_AUTOC_LMS_MASK); + hw->mac.link_settings_loaded = TRUE; + } + + /* Store the permanent mac address */ + hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr); + + return status; +} + +#endif /* NO_A0_SUPPORT */ +/** + * ixgbe_reset_hw_82598 - Performs hardware reset + * @hw: pointer to hardware structure + * + * Resets the hardware by resetting the transmit and receive units, masks and + * clears all interrupts, performing a PHY reset, and performing a link (MAC) + * reset. + **/ +s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw) +{ + s32 status = IXGBE_SUCCESS; + u32 ctrl; + u32 gheccr; + u32 i; + u32 autoc; + u8 analog_val; + + /* Call adapter stop to disable tx/rx and clear interrupts */ + hw->mac.ops.stop_adapter(hw); + + /* + * Power up the Atlas Tx lanes if they are currently powered down. + * Atlas Tx lanes are powered down for MAC loopback tests, but + * they are not automatically restored on reset. + */ + hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, &analog_val); + if (analog_val & IXGBE_ATLAS_PDN_TX_REG_EN) { + /* Enable Tx Atlas so packets can be transmitted again */ + hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, + &analog_val); + analog_val &= ~IXGBE_ATLAS_PDN_TX_REG_EN; + hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, + analog_val); + + hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_10G, + &analog_val); + analog_val &= ~ IXGBE_ATLAS_PDN_TX_10G_QL_ALL; + hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_10G, + analog_val); + + hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_1G, + &analog_val); + analog_val &= ~IXGBE_ATLAS_PDN_TX_1G_QL_ALL; + hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_1G, + analog_val); + + hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_AN, + &analog_val); + analog_val &= ~IXGBE_ATLAS_PDN_TX_AN_QL_ALL; + hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_AN, + analog_val); + } + + /* Reset PHY */ + if (hw->phy.reset_disable == FALSE) + hw->phy.ops.reset(hw); + + /* + * Prevent the PCI-E bus from from hanging by disabling PCI-E master + * access and verify no pending requests before reset + */ + if (ixgbe_disable_pcie_master(hw) != IXGBE_SUCCESS) { + status = IXGBE_ERR_MASTER_REQUESTS_PENDING; + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + } + + /* + * Issue global reset to the MAC. This needs to be a SW reset. + * If link reset is used, it might reset the MAC when mng is using it + */ + ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); + IXGBE_WRITE_REG(hw, IXGBE_CTRL, (ctrl | IXGBE_CTRL_RST)); + IXGBE_WRITE_FLUSH(hw); + + /* Poll for reset bit to self-clear indicating reset is complete */ + for (i = 0; i < 10; i++) { + usec_delay(1); + ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); + if (!(ctrl & IXGBE_CTRL_RST)) + break; + } + if (ctrl & IXGBE_CTRL_RST) { + status = IXGBE_ERR_RESET_FAILED; + DEBUGOUT("Reset polling failed to complete.\n"); + } + + msec_delay(50); + + gheccr = IXGBE_READ_REG(hw, IXGBE_GHECCR); + gheccr &= ~((1 << 21) | (1 << 18) | (1 << 9) | (1 << 6)); + IXGBE_WRITE_REG(hw, IXGBE_GHECCR, gheccr); + + /* + * AUTOC register which stores link settings gets cleared + * and reloaded from EEPROM after reset. We need to restore + * our stored value from init in case SW changed the attach + * type or speed. If this is the first time and link settings + * have not been stored, store default settings from AUTOC. + */ + autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); + if (hw->mac.link_settings_loaded) { + autoc &= ~(IXGBE_AUTOC_LMS_ATTACH_TYPE); + autoc &= ~(IXGBE_AUTOC_LMS_MASK); + autoc |= hw->mac.link_attach_type; + autoc |= hw->mac.link_mode_select; + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc); + } else { + hw->mac.link_attach_type = + (autoc & IXGBE_AUTOC_LMS_ATTACH_TYPE); + hw->mac.link_mode_select = (autoc & IXGBE_AUTOC_LMS_MASK); + hw->mac.link_settings_loaded = TRUE; + } + + /* Store the permanent mac address */ + hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr); + + return status; +} + +/** + * ixgbe_set_vmdq_82598 - Associate a VMDq set index with a rx address + * @hw: pointer to hardware struct + * @rar: receive address register index to associate with a VMDq index + * @vmdq: VMDq set index + **/ +s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq) +{ + u32 rar_high; + + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar)); + rar_high &= ~IXGBE_RAH_VIND_MASK; + rar_high |= ((vmdq << IXGBE_RAH_VIND_SHIFT) & IXGBE_RAH_VIND_MASK); + IXGBE_WRITE_REG(hw, IXGBE_RAH(rar), rar_high); + return IXGBE_SUCCESS; +} + +/** + * ixgbe_blink_led_start_82598 - Blink LED based on index. + * @hw: pointer to hardware structure + * @index: led number to blink + **/ +s32 ixgbe_blink_led_start_82598(struct ixgbe_hw *hw, u32 index) +{ + ixgbe_link_speed speed = 0; + bool link_up = 0; + u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + + /* + * Link must be up to auto-blink the LEDs on the 82598EB MAC; + * force it if link is down. + */ + hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); + + if (!link_up) { + autoc_reg |= IXGBE_AUTOC_FLU; + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); + msec_delay(10); + } + + led_reg &= ~IXGBE_LED_MODE_MASK(index); + led_reg |= IXGBE_LED_BLINK(index); + IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); + IXGBE_WRITE_FLUSH(hw); + + return IXGBE_SUCCESS; +} + +/** + * ixgbe_blink_led_stop_82598 - Stop blinking LED based on index. + * @hw: pointer to hardware structure + * @index: led number to stop blinking + **/ +s32 ixgbe_blink_led_stop_82598(struct ixgbe_hw *hw, u32 index) +{ + u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + + autoc_reg &= ~IXGBE_AUTOC_FLU; + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); + + led_reg &= ~IXGBE_LED_MODE_MASK(index); + led_reg &= ~IXGBE_LED_BLINK(index); + IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); + IXGBE_WRITE_FLUSH(hw); + + return IXGBE_SUCCESS; +} |