| Age | Commit message (Collapse) | Author |
|---|
|
dhclient-script and disktab files in architectures where this wasn't
already being done.
OK deraadt@.
|
|
|
|
logic. As result, MDSETS gone from everything but mac68k.
MDSETS now treated as a list of complete file names to add to THESETS,
allowing more MD flexibility, i.e. may or may not be .tgz files.
All traces of tar.gz removed. Not used for sets since 2.7 or so. As a
result of code simplification from not having to consider tar.gz, the
functions get_sets(), make_lastset(), and set_not_done() are
eliminated, along with the global SETS.
Build THESETS and DEFAULTSETS to contain full file names.
Always install sets in the order they appear in THESETS, keeping
siteXX last but without needing special logic. More predictable for
user if a lot of set additions and removals done before being
satisfied, as the sets are now installed in the same order they appear
in the selection list.
Remove ability to look for non-set .tgz/.tar.gz files. The job of the
install scripts is to install the standard sets in a simple and
rational way. Not to install general tar balls. The user can do that
post-install or simply '!' out to do it during install. On their head
be it.
If no sets are found in a specified source, list the filenames in
THESETS to show what is being looked for.
|
|
|
|
machdep.allowaperture. Remove the setting of machdep.allowaperture
from md_installboot().
Add MDXAPERTURE variable to relevant architectures.
Add a new function set_machdep_allowaperture(). It is called *after*
install_sets() (which changes when the X Window question is asked), and
if MDXAPERTURE is present modifies sysctl.conf.
Shrinks overall size for i386, macppc, sparc64 (which used md_questions
for machdep.allowaperture) but increases size a bit for other
architectures since set_machep_allowaperture is in install.sub.
|
|
if the ` is not individually escaped and the here document as a whole
is not escaped. (i.e. cat << \__EOT).
|
|
1) Saving one boot's worth of dmesg in /tmp/dmesg.boot
2) Using sed to scan for devices and pull out names in
new get_diskdevs() and get_cddevs() in install.sub
3) Saving any md disk/cd sed patterns in MDDISKDEVS and
MDCDDEVS variables.
|
|
simply echo'd a single word if present at all.
Replace with variables MDFSTYPE and MDFSOPTS if required. Rework logic
in install.sub's mount_a_disk() to always include 'ro' as an option to
the mount command. This allows even those arch's with MDFSTYPE to
usually get by without MDFSOPTS.
ok deraadt@
|
|
output of both was essentially identical on all architectures. Replace
with welcome_banner() and not_going_to_install() in install.sub.
Abstract common verbiage from md_congrats() into congrats() which
calls md_congrats() for any architecture specific additional verbiage.
Reword things so ${MODE} can be plausibly used in more places.
Remove extraneous #!/bin/sh in hp300 install.md.
ok deraadt@ espie@
|
|
Abstract out common md_set_term() code into set_term() in install.sub,
calling md_set_term() from set_term() to do machine dependent stuff.
Currently only i386 does anything - keyboard mappings.
Add MDTERM variable to allow install.md to set proper default terminal
type. Default to vt220.
Eliminate md_get_partition_range() as useless since every architecture
returned '[a-p]'.
Make default term for all mvme* architectures vt100 as requested by miod@.
ok deraadt@ millert@ miod@
|
|
use later, plus a few rcsid vicinity cleanups; millert@ ok
|
|
Make all fsck list file entries simply be:
LINK instbin sbin/fsck_ffs sbin/fsck
|
|
|
|
|
|
|
|
smaller again
|
|
|
|
|
|
ask() takes 2 parameters. The first one is the question to
ask the user, and the 2nd is the default answer.
Shrinks and makes the code clearer.
From espie@ with some tweaking, ok deraadt@.
|
|
|
|
- remove dead hp300 stuff
ok millert@, espie@
|
|
|
|
|
|
|
|
|
|
|
|
|
|
a) Add /var/run to the filesystem created when the installation media
boots. This allows the creation and use of the dhclient.pid file.
Synchronize all mtree.conf files in architectures using miniroot.
b) Rework the traps used in upgrade.sh and install.sh so that HUP,
INT, QUIT, TERM and EXIT all invoke a cleanup function that kills an
active dhclient, unmounts all filesystems and fsck's -p all devices
in /etc/fstab, or just /mnt if /etc/fstab is not present.
c) Make sure the actions of the cleanup function are visible, thus
eliminating the long delay with no feedback at the end of the
upgrade/install script, after the congratulatory message.
d) Reduce manual parsing of fstab files by using umount -a to
unmount all mounted filesystems.
e) Since the new cleanup function tries to unmount all filesystems,
use the presence of /etc/fstab, rather than a difference between
`df /` and `df /mnt`, to determine if an install is being restarted
in a state where disk initialization can be skipped.
f) Change munge_fs, check_fs, mount_fs, remount_fs so that they
all 'know' about /etc/fstab rather than passing the same
parameter in all the time.
g) Use input redirection on munge_fs to read correct file, rather
than passing a file name as a parameter.
h) Indent code for various smaller functions.
i) Eliminate some subshell usage to simplify code further.
j) Display pretty messages during fsck -p to clearly indicate success
or failure of fsck, rather than just dumping fsck output.
k) Always run mount_fs in install.sh, even if disk initialization is
being skipped, because the trap should have unmounted all filesystems
when the last run terminated.
ok weingart@ millert@
|
|
|
|
|
|
|
|
anything ...' during install and/or upgrade on some archs.
On sparc, sparc64, sun3 and vax fix a typo ('echo Welcome' ->
'Welcome') in here-document displayed in md_welcome_banner().
|
|
/etc/services used during installations.
This way it is not necessary to run the install script before
using commands requiring these files.
Requested by deraadt@.
|
|
that use the miniroot install scripts.
During an install, donetconfig() in miniroot/install.sub now
creates a minimal /etc/protocols and /etc/services.
During an upgrade, enable_network() now copies the existing
protocols and services files into /etc.
Saves approximately 13K on floppy/cd images.
|
|
|
|
for several months.
|
|
change ARCH=ARCH sed to use `arch -ks` so it has the proper macppc
directory when referring to the ftp or CD directories.
|
|
|
|
gnu/usr.bin before usr.bin, until our grep replaces gnu grep
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
