| Age | Commit message (Expand) | Author |
|---|
| 2006-07-10 | Remove the error_cnt cacluation, this only makes sense when the supplied | Dale Rahn |
| 2006-07-10 | As pointed out by miod, cpu_initclocks() can use setstatclockrate(), the | Dale Rahn |
| 2006-07-10 | Adding missing $OpenBSD$ tags, pointed out by miod. | Dale Rahn |
| 2006-07-02 | count interrupts (uvmexp). | Dale Rahn |
| 2006-06-27 | Rewritten clock driver for 80219/80321, actually manages seperate stat | Dale Rahn |
| 2006-06-19 | Close a race in the interrupt handler code. | Dale Rahn |
| 2006-06-17 | Fix error where soft irq mask was not initialized for IPL_HIGH, and cleanup. | Dale Rahn |
| 2006-06-15 | rewritten, simplifed interrupt controller for 80321, half the lines | Dale Rahn |
| 2006-06-15 | Ricoh rtc support for armish, driver from netbsd. | Dale Rahn |
| 2006-06-10 | I2C support for 80321/80219 | Dale Rahn |
| 2006-06-02 | cleanup, move thecus board_reset from MI arm/xscale into armish dir. | Dale Rahn |
| 2006-06-01 | After changing J3 to J4 on the thecus board, serial interrupts work just | Dale Rahn |
| 2006-06-01 | Splraise is strictly to increase spl, do not lower. | Dale Rahn |
| 2006-06-01 | current_ipl_level is a value, not a mask, do not '|=' into it. | Dale Rahn |
| 2006-06-01 | Just say NO to noisy dmesg. | Dale Rahn |
| 2006-06-01 | IO addresses will always be in the right range, this check is wrong. | Dale Rahn |
| 2006-05-31 | correctly perform bus base/physical addr translation. | Dale Rahn |
| 2006-05-29 | Tags. | Dale Rahn |
| 2006-05-29 | Add support for i80321 based systems. | Dale Rahn |
| 2006-04-04 | Add input routines to the i2s layer to support future Zaurus audio input. | Christopher Pascoe |
| 2006-04-04 | Add pxa2x0_dma_from_fifo to support DMA from internal peripheral FIFOs | Christopher Pascoe |
| 2006-04-04 | Abort any DMA that is in progress before changing the DMA completion handler, | Christopher Pascoe |
| 2006-04-04 | Configure the I2S controller's GPIOs, not than the USB's. | Christopher Pascoe |
| 2006-03-07 | Fix collision between SI_SOFTSERIAL and OS timers in the interrupt mask. | Uwe Stuehler |
| 2006-03-07 | Add the proper constant to replace a magic interrupt number. | Uwe Stuehler |
| 2005-12-22 | Fully implemented microtime() operation. | Dale Rahn |
| 2005-12-22 | do not do delay(HUGEVALUE) after enabling/disabling the lcd dma. yes, it | Theo de Raadt |
| 2005-12-22 | remove another debug message | Theo de Raadt |
| 2005-12-22 | silence setperf code | Theo de Raadt |
| 2005-12-20 | volatile variable for looping; ok drahn | Theo de Raadt |
| 2005-12-20 | Add machdep.maxspeed sysctl to change the meaning of hw.setperf=100 on zaurus, | Dale Rahn |
| 2005-12-20 | switch to using clock4 instead of clock0 so that we get clocks when running | Dale Rahn |
| 2005-12-14 | Don't hard-code card present and number of socket bits in the PCMCIA bus | Uwe Stuehler |
| 2005-12-13 | It would seem that some cards do not get reset correctly if RESET is | Uwe Stuehler |
| 2005-12-05 | - Run only the necessary code to transition from one speed to another. | Uwe Stuehler |
| 2005-12-02 | add registers for 4 new clocks | Theo de Raadt |
| 2005-12-02 | no 91Mhz mode for now, because the OSCR0 does not run in low-power mode; | Uwe Stuehler |
| 2005-11-23 | use proper bus_size_t for register offsets and not bus_addr_t; uwe@ miod@ tes... | Michael Shalayeff |
| 2005-11-19 | Remove unnecessary lockmgr() archaism that was costing too much in terms | Pedro Martelletto |
| 2005-11-19 | Remove superfluous statement-ending semi-colons. i.e., "return foo;;" should | Aaron Campbell |
| 2005-11-11 | round clock up | Theo de Raadt |
| 2005-10-31 | show the speed status in hw.cpuspeed; ok drahn | Theo de Raadt |
| 2005-10-31 | On suspend/resume save the current time to the RTC earlier and restore it later | Dale Rahn |
| 2005-09-22 | NEWINTR is not an option on OpenBSD. | Dale Rahn |
| 2005-09-15 | Stop compiling the texte console rotation code #ifdef __zaurus__, but use | Miod Vallat |
| 2005-08-12 | Do not notify apmd of APM_CRIT_SUSPEND_REQ events; apmd makes us fall | Uwe Stuehler |
| 2005-08-09 | - Don't depend on the APM_CRIT_RESUME event to run PWR_RESUME power hooks | Uwe Stuehler |
| 2005-08-08 | Avoid overlap in USB hard and the soft interrupt bits, update comments | Uwe Stuehler |
| 2005-07-18 | remove trailing newline in panic(9); ok millert@ and deraadt@ | Federico G. Schwindt |
| 2005-07-18 | Initialize UART registers after resume, and make functions non-static. | Uwe Stuehler |
