| Age | Commit message (Expand) | Author |
|---|
| 2007-05-25 | "interupt" -> "interrupt" in various comments. Mostly from Diego Casati. | Kenneth R Westerback |
| 2007-05-21 | timecounters for armish. | Dale Rahn |
| 2007-05-19 | Implement splassert for armish and zaurus. | Miod Vallat |
| 2007-05-15 | Dummy mutex code for arm platforms. ok drahn@ deraadt@ | Miod Vallat |
| 2007-05-09 | diable -> disable | Miod Vallat |
| 2007-03-29 | Add power hook to scoop(4), replacing the Zaurus-specific scoop_* calls in | Uwe Stuehler |
| 2007-03-24 | Call the new ohci_checkrev function on xscale, otherwise the USB version | Christopher Pascoe |
| 2007-03-18 | typo | Theo de Raadt |
| 2007-03-18 | Support the PXA27x SD/SDIO/MMC controller on Zaurus | Uwe Stuehler |
| 2007-02-25 | add missing USBD_FORCE_SHORT_XFER checks, put back some code I had for a | Dale Rahn |
| 2007-02-25 | Defines to make isr status more useable. Bit patterns for debug prints. | Dale Rahn |
| 2007-02-24 | move debug print into debug block. | Dale Rahn |
| 2007-02-24 | Add my copyright, since I took the skeleton driver and made it complete. | Dale Rahn |
| 2007-02-23 | Use the maxpacket len from the pipe, not hardcoded. properly deal | Dale Rahn |
| 2007-02-15 | TX is working fine, turn off debug. | Dale Rahn |
| 2007-02-15 | Add a mapping for logical to physical endpoints, otherwise data tries to | Dale Rahn |
| 2007-02-15 | Fix transmit packet termination. odd length and 64 byte multiple packets | Dale Rahn |
| 2007-02-13 | Add a delay for ep0 handling. Dunno why, but without debug prints it would | Dale Rahn |
| 2007-02-13 | USB client mode with cdce function driver is coming along, RX and TX kinda work. | Dale Rahn |
| 2007-02-12 | Reduce debug. | Dale Rahn |
| 2007-02-12 | If SMAC is set in the correct register, it works much better, also set | Dale Rahn |
| 2007-02-07 | Several improvements to the usb client code. Still not working. | Dale Rahn |
| 2007-01-11 | do not report the clock frequencies on arm becuase there is no | Robert Nagy |
| 2006-12-20 | Enable recursive interrupts on armish. nudge by deraadt@ | Dale Rahn |
| 2006-12-14 | Make pci subsystem aware of domains. Each host bridge gets assigned a unique | Mark Kettenis |
| 2006-12-14 | - enable nested interrupts on zaurus. most obvious side-effect of this is | Niall O'Higgins |
| 2006-12-12 | Complete gwk's previous patch to stop setperf methods from returning | Dimitry Andric |
| 2006-11-28 | add needs-flag to allow pxaudc to compile without usbf (to get the | Uwe Stuehler |
| 2006-11-25 | Initial USB device controller (UDC) and USB CDC Ethernet function support | Uwe Stuehler |
| 2006-10-19 | s/Mhz/MHz/ in comments and printf() strings | Tom Cosgrove |
| 2006-08-24 | missing newline in a printf | Theo de Raadt |
| 2006-07-20 | Get rid of the 'nextevent out of bounds' error message, if interrupts | Dale Rahn |
| 2006-07-10 | Remove the error_cnt cacluation, this only makes sense when the supplied | Dale Rahn |
| 2006-07-10 | As pointed out by miod, cpu_initclocks() can use setstatclockrate(), the | Dale Rahn |
| 2006-07-10 | Adding missing $OpenBSD$ tags, pointed out by miod. | Dale Rahn |
| 2006-07-02 | count interrupts (uvmexp). | Dale Rahn |
| 2006-06-27 | Rewritten clock driver for 80219/80321, actually manages seperate stat | Dale Rahn |
| 2006-06-19 | Close a race in the interrupt handler code. | Dale Rahn |
| 2006-06-17 | Fix error where soft irq mask was not initialized for IPL_HIGH, and cleanup. | Dale Rahn |
| 2006-06-15 | rewritten, simplifed interrupt controller for 80321, half the lines | Dale Rahn |
| 2006-06-15 | Ricoh rtc support for armish, driver from netbsd. | Dale Rahn |
| 2006-06-10 | I2C support for 80321/80219 | Dale Rahn |
| 2006-06-02 | cleanup, move thecus board_reset from MI arm/xscale into armish dir. | Dale Rahn |
| 2006-06-01 | After changing J3 to J4 on the thecus board, serial interrupts work just | Dale Rahn |
| 2006-06-01 | Splraise is strictly to increase spl, do not lower. | Dale Rahn |
| 2006-06-01 | current_ipl_level is a value, not a mask, do not '|=' into it. | Dale Rahn |
| 2006-06-01 | Just say NO to noisy dmesg. | Dale Rahn |
| 2006-06-01 | IO addresses will always be in the right range, this check is wrong. | Dale Rahn |
| 2006-05-31 | correctly perform bus base/physical addr translation. | Dale Rahn |
| 2006-05-29 | Tags. | Dale Rahn |
