| Age | Commit message (Expand) | Author |
|---|
| 2006-10-02 | One <arm/exec.h> to bind them all. | Miod Vallat |
| 2006-09-27 | Add Maxim/Dallas DS2490 USB 1-Wire adapter driver. | Alexander Yurchenko |
| 2006-09-27 | Add files.onewire to all our USB archs, it will be used soon. | Alexander Yurchenko |
| 2006-09-15 | Reset the sysfail led on thecus, so that it doesn't blink | Dale Rahn |
| 2006-08-26 | Set flags to 0x0001 for fintek(4), to make the fans run at full speed. | Mark Kettenis |
| 2006-08-18 | add ucycom@uhidev and ucom@ucycom on the usb machines (docs are forthcoming) | Jason Wright |
| 2006-08-14 | Enable uslcom(4) and uark(4) on all the USB capable archs. | Jonathan Gray |
| 2006-08-12 | Setting d_secsize to DEV_BSIZE (or 1 << DEV_BSHIFT, or 512) and then | Kenneth R Westerback |
| 2006-08-11 | add rum(4) on arches where ural(4) is enabled. | Damien Bergamini |
| 2006-08-01 | Make RB_POWERDOWN work on the Thecus. | Mark Kettenis |
| 2006-08-01 | Enable pcaled0. | Mark Kettenis |
| 2006-08-01 | trust the bootloader about the root disk; ok kettenis | Theo de Raadt |
| 2006-07-30 | spacing | Theo de Raadt |
| 2006-07-30 | With new kernel and bootloader, argument passing now works, version 1.0. | Dale Rahn |
| 2006-07-30 | Perform a limited PCI probe to locate the wdc on iodata/thecus, boot loader | Dale Rahn |
| 2006-07-29 | Make _rtt reset the machine. | Mark Kettenis |
| 2006-07-29 | ework armish bootloader into an interactive one, much like i386 has. | Mark Kettenis |
| 2006-07-29 | only enter for armish | Theo de Raadt |
| 2006-07-28 | Pass the end of the symbol table to the kernel. | Mark Kettenis |
| 2006-07-28 | no man page for now | Theo de Raadt |
| 2006-07-28 | should install into /usr/mdec/ | Theo de Raadt |
| 2006-07-28 | enter boot | Theo de Raadt |
| 2006-07-28 | First stab at an armish bootloader. It will load /bsd from the drive in the | Mark Kettenis |
| 2006-07-27 | Compile all kernels with -Wstack-usage-larger-than-2047, now that all | Miod Vallat |
| 2006-07-20 | assume root is always on wd0a, for now | Theo de Raadt |
| 2006-07-17 | Switch to a three-phase pci resource fixup: | Dale Rahn |
| 2006-07-14 | Add a major line for wd, for kernels with root on wd0a to work. | Miod Vallat |
| 2006-07-12 | Fix dependencies | Miod Vallat |
| 2006-07-12 | Orphaned stuff. | Miod Vallat |
| 2006-07-11 | Remove old debug goo; drahn@ ok | Miod Vallat |
| 2006-06-26 | Kludge around the fact that redboot uses ELF's vaddr, however maps | Dale Rahn |
| 2006-06-19 | move clock_subr.c to a better place, and now it is always in the kernel | Theo de Raadt |
| 2006-06-17 | Dont disable siop, add pcalcd, commented for now (no gpioctl on ramdisk). | Dale Rahn |
| 2006-06-17 | Add pcaled with it's gpio attachment. Make gpio at iopxs not be '0' but '*' | Dale Rahn |
| 2006-06-16 | On the road to certance support. | Dale Rahn |
| 2006-06-16 | If there is going to be a kludge to change the irq for com, do it early | Dale Rahn |
| 2006-06-15 | The process is not: build, ifdef, commit. argh. | Dale Rahn |
| 2006-06-15 | rewritten, simplifed interrupt controller for 80321, half the lines | Dale Rahn |
| 2006-06-15 | Hack to attach the iodata PLD device, it controls the front panel LEDs | Dale Rahn |
| 2006-06-15 | All all 256MB on the thecus to configure, by raising the amount of | Dale Rahn |
| 2006-06-15 | sane irq numbers for pci interrupts, remove uncertanty on armish irq table. | Dale Rahn |
| 2006-06-15 | Fan controller for Thecus N2100, still needs more work, currently sets the | Dale Rahn |
| 2006-06-15 | Ricoh rtc support for armish, driver from netbsd. | Dale Rahn |
| 2006-06-15 | whitespace cleanup | Dale Rahn |
| 2006-06-10 | Add IIC attachment/probe. no IIC devices yet. | Dale Rahn |
| 2006-06-10 | bring PHYS address in sync with RAMDISK, matches the addresss redboot | Dale Rahn |
| 2006-06-10 | include i2c bits instead of dummying out i2c_bitbang. | Dale Rahn |
| 2006-06-04 | Shrink VM_PHYSSEG_MAX to 1 on platforms where physical memory is contiguous | Miod Vallat |
| 2006-06-02 | cleanup, move thecus board_reset from MI arm/xscale into armish dir. | Dale Rahn |
| 2006-06-01 | After changing J3 to J4 on the thecus board, serial interrupts work just | Dale Rahn |
