summaryrefslogtreecommitdiff
path: root/sys/dev/ic/bwi.c
AgeCommit message (Expand)Author
2008-02-25Make bwi compile in debug mode again.Marcus Glocker
2008-02-25Sync up with DragonFlyBSD driver. Please read their commit messageMarcus Glocker
2008-02-16Zap KKASSERT porting macro and use KASSERT instead.Marcus Glocker
2008-02-16Count output packets.Marcus Glocker
2008-02-16Replace bwi_rate2plcp() with ieee80211_rate2plcp().Marcus Glocker
2008-02-16Fix spacing / comments.Marcus Glocker
2008-02-16While importing the driver a lot of printf's have been converted toMarcus Glocker
2008-02-16Report rssi and rate in rx radio tap.Marcus Glocker
2008-02-16Better support for 11b mode.Marcus Glocker
2008-02-16Remove some double prototype definitions.Marcus Glocker
2008-02-16Always print device name in front of debug messages.Marcus Glocker
2007-11-17- Add more LED support, like activity blinking (though just supportingMarcus Glocker
2007-10-18Add some first LEDs support. Tested on my cardbus Linksys WPC54G Ver 3.Marcus Glocker
2007-10-04Since we know the firmware load works, merge the single firmware filesMarcus Glocker
2007-10-01Spacing.Marcus Glocker
2007-10-01Fix `bogus xmit rate setup' panic, which mostly happened while associatingMarcus Glocker
2007-10-01remove rate_fb variable as it always gets set to the same valueJonathan Gray
2007-10-01Print the MAC address.Jonathan Gray
2007-10-01Disable default debug setting, make tx power map printing debug only.Jonathan Gray
2007-10-01Use uint_* consistent.Marcus Glocker
2007-09-30Spacing.Marcus Glocker
2007-09-30Don't count interrupts with state "not of interest".Marcus Glocker
2007-09-30BWI_BBP_ATTEN is a 16-bit register, so use CSR_WRITE_2 to access it.Mark Kettenis
2007-09-29Fix two panic's on macppc. Allows me first network communication overMarcus Glocker
2007-09-27Spacing.Marcus Glocker
2007-09-27Add automatic rate control (AMRR).Marcus Glocker
2007-09-27Spacing.Marcus Glocker
2007-09-27Kill __BIT* macros.Marcus Glocker
2007-09-24Add radio tap support. We still need to calculate correct RX rate andMarcus Glocker
2007-09-23Fix page fault kernel crash when changing media and device is up.Marcus Glocker
2007-09-23Add missing device name printf arguments for firmware load error output.Marcus Glocker
2007-09-23More debug ouput cleanup.Marcus Glocker
2007-09-23Correctly clear PCI_STATUS_TARGET_TARGET_ABORT bit.Marcus Glocker
2007-09-23Properly handle the physical address in bwi_encap() as well.Jonathan Gray
2007-09-23Make sure to set physical address in bwi_newbuf()Jonathan Gray
2007-09-18Drag back the original DragonFlyBSD firmware loading routines, so we canMarcus Glocker
2007-09-17If device is down, don't handle any interrupts. Even don't read theMarcus Glocker
2007-09-17Several DPRINTF arguments was missing, which can lead to ugly kernelMarcus Glocker
2007-09-17In case of IV load failure free ucode.Marcus Glocker
2007-09-16Remove more obsolete firmware specific bits.Marcus Glocker
2007-09-16Remove obsolete firmware specific bits.Marcus Glocker
2007-09-16Better version of fake KKASSERT until they are changed properly.Jonathan Gray
2007-09-16Do sc_disable when device gets stopped.Marcus Glocker
2007-09-16Clear error before starting m_defrag() equivalent.Jonathan Gray
2007-09-16Move some noisy debug printfs to higher levels.Jonathan Gray
2007-09-16CardBus works much better when sc_enable is called.Jonathan Gray
2007-09-16Free ucode if an error happens while FW / IV load. Always return a properMarcus Glocker
2007-09-16Convert most of the remaining non firmware handling code.Jonathan Gray
2007-09-16Remove most of the __unused due to to code being enabled.Jonathan Gray
2007-09-15Adapt firmware images prefix to driver name. Needs bump to firmwareMarcus Glocker
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-21 11:00:42 +0000