| Age | Commit message (Expand) | Author |
|---|
| 2006-11-28 | add additional link states to report the half duplex / full duplex | Reyk Floeter |
| 2006-11-28 | some additional registers. | Brad Smith |
| 2006-11-28 | sync with new miidevs entries. | Brad Smith |
| 2006-11-28 | regen | Brad Smith |
| 2006-11-28 | rename Marvell Gig PHY E1000_5/6 to E1116/E1118. | Brad Smith |
| 2006-11-02 | simplify parent driver matching code a bit. no-op change. | Brad Smith |
| 2006-10-22 | Set Jumbo frame settings for Jumbo capable bge(4) adapters. | Brad Smith |
| 2006-10-20 | remove the IFM_100_T4 switch case for the manual media code, brgphy(4) | Brad Smith |
| 2006-10-20 | attach for the Broadcom BCM5755 ASIC based chipsets as well. | Brad Smith |
| 2006-10-20 | regen | Brad Smith |
| 2006-10-20 | add PHY id for the Broadcom BCM5755 ASIC based chipsets. | Brad Smith |
| 2006-10-20 | move the Jumbo frame settings and Ethernet@Wirespeed code into separate | Brad Smith |
| 2006-10-19 | add a PHY workaround for the 5787 ASIC based chipsets. | Brad Smith |
| 2006-10-19 | Rearrange the code a bit, rename a few functions and make brgphy(4) use | Brad Smith |
| 2006-10-15 | fix parent driver match in brgphy_reset(), simplify code a bit as well, don't | Brad Smith |
| 2006-10-15 | attach to the Broadcom BCM5787 PHY. | Brad Smith |
| 2006-10-15 | regen | Brad Smith |
| 2006-10-15 | add another OUI id for Broadcom and the BCM5787 PHY id. | Brad Smith |
| 2006-10-11 | revert rev 1.54. This causes breakage with the PHY on a 5704 A3 chipset; | Brad Smith |
| 2006-10-09 | revert the last two changes. the changes were causing brgphy@gem to panic. | Brad Smith |
| 2006-10-08 | set Jumbo frame settings for Jumbo capable bge(4) adapters. | Brad Smith |
| 2006-10-08 | refactor the code a bit, use the bge(4) PHY flags and add another | Brad Smith |
| 2006-10-08 | - g/c unused code. | Brad Smith |
| 2006-10-07 | g/c unused code. | Brad Smith |
| 2006-10-02 | do not bother to read the esr and isr registers in the status routine just | Brad Smith |
| 2006-10-02 | return EINVAL for the Gig manual media types when attached to a | Brad Smith |
| 2006-10-01 | pack several boolean fields into the existing bge_flags field. | Brad Smith |
| 2006-10-01 | initial pieces for the 88E3082 Fast Ethernet PHY. untested at the moment. | Brad Smith |
| 2006-10-01 | add a few new Marvell ids. | Brad Smith |
| 2006-10-01 | regen | Brad Smith |
| 2006-10-01 | add a few new Marvell ids. | Brad Smith |
| 2006-09-27 | regen | Jonathan Gray |
| 2006-09-27 | Add another two Vitesse PHYs, one from jmc's nfe(4), one from an | Jonathan Gray |
| 2006-09-17 | do not fill in the anar for the manual 1000baseT media setting case. | Brad Smith |
| 2006-08-28 | revert flags usage commits. too close to release. will go in post release ins... | Brad Smith |
| 2006-08-28 | Fix manual media types by always leaving the PHY in autoneg mode but adjusting | Brad Smith |
| 2006-08-27 | pack several boolean fields into the existing bge_flags field. | Brad Smith |
| 2006-08-21 | another id. | Brad Smith |
| 2006-08-21 | regen | Brad Smith |
| 2006-08-21 | another Marvell Gig PHY. | Brad Smith |
| 2006-08-11 | typo, settning -> setting | Brad Smith |
| 2006-08-05 | add sys/timeout.h and remove redundant sys/socket.h header. | Brad Smith |
| 2006-08-05 | Simplify autoneg code. Tested with a fibre sk and lge. | Brad Smith |
| 2006-07-28 | Simplify autoneg code a bit. Tested on a few sk(4)'s and an axe(4). | Brad Smith |
| 2006-07-28 | another Marvell Gig PHY. | Brad Smith |
| 2006-07-28 | regen | Brad Smith |
| 2006-07-28 | another Marvell Gig PHY. | Brad Smith |
| 2006-07-23 | add sys/timeout.h | Brad Smith |
| 2006-07-23 | revert back to the old brgphy_mii_phy_auto() which simplifies the autoneg code. | Brad Smith |
| 2006-07-22 | On the Gig PHYTER, for whatever reason, the 10baseT-related bits of the | Brad Smith |
