summaryrefslogtreecommitdiff
path: root/sys/dev/mii
AgeCommit message (Expand)Author
2008-04-30regenBrad Smith
2008-04-30Add the id for the Marvell 88E3016 10/100 PHYBrad Smith
2008-04-26Adjust the output voltage for BCM5906 PHY otherwise it might not beBrad Smith
2008-04-20Add a workaround for a CRC bug errata with BCM5701 A0 and B0 chipsetBrad Smith
2008-04-02Add support for the DP83865.Mark Kettenis
2008-04-02regenMark Kettenis
2008-04-02Add the National Semiconductor DP83865 Gigabit PHY.Mark Kettenis
2008-04-02regenBrad Smith
2008-04-02Add the Cicada CS8204 quad port PHY.Brad Smith
2008-04-02Return right away for unknown media types instead of fallingBrad Smith
2008-04-01Add some defines and remove some of the magic numbers from the code.Brad Smith
2008-03-21Add defines for 1Gbps/2.5Gbps fiber interfaces.Brad Smith
2008-03-12Fix comment typo, of -> if.Brad Smith
2008-03-02Add missing half duplex flag for 100baseT4.Brad Smith
2008-03-02Correct a status flag which could cause half duplex to be reported forBrad Smith
2008-02-28Update for the BCM5706 miidevs entry change.Brad Smith
2008-02-28regenBrad Smith
2008-02-28- Update the BCM5706 PHY entry to also mention SX since this id is sharedBrad Smith
2008-01-31recognize the BCM5722 PHY.Brad Smith
2008-01-31regenBrad Smith
2008-01-31add the Broadcom BCM5722 PHY id.Brad Smith
2007-11-25Set half duplex flag when appropriate and some minor cleaning.Brad Smith
2007-11-18eephy_mii_phy_auto() was deleted in r1.38. So delete the declaration too.Kenneth R Westerback
2007-11-06regenMark Kettenis
2007-11-06Add Enable/Agere LU3X31T2.Mark Kettenis
2007-10-30Initial port of Sepherosa Ziehau's DragonFlyBSD driversJonathan Gray
2007-10-30regenJonathan Gray
2007-10-30Add Agere ET1011 10/100/1000 PHYJonathan Gray
2007-10-13Add support for BCM5906.Mark Kettenis
2007-10-10Add support for the RTL8211B PHY based on a patch byJonathan Gray
2007-10-06Oops, committed this with a typo, which made it do not quite the right thing.Mark Kettenis
2007-10-05Disable fiber/copper auto-selection on the 88E1111 if it is in RGMII mode, toMark Kettenis
2007-09-17- Use a 64-bit int for the baudrate within the ifmedia_baudrate struct andBrad Smith
2007-09-17regenMark Kettenis
2007-09-17Add another OUI for Broadcom, and add the PHY for the Broadcom BCM5906.Mark Kettenis
2007-08-30PHY on D495GCCR boardChris Kuethe
2007-08-30regenChris Kuethe
2007-08-30Intel PHY on D945GCCR boardChris Kuethe
2007-02-11Add support for fiber on the 88E1112 (88E8021/22 integrated PHY).Mark Kettenis
2007-02-10Use right flow control autonegotiation bits for 1000baseX.Mark Kettenis
2007-01-30Rough in more support for 5787/5755 chips so far known to not work orKenneth R Westerback
2007-01-27In autoneg mode, use RL_MEDIASTAT on re(4), like we do on rl(4) already.Miod Vallat
2007-01-21Use MII_ANEGTICKS_GIGE instead of MII_ANEGTICKS.Mark Kettenis
2007-01-10Flow control support for bge(4)/brgphy(4). From brad@ based on code fromMark Kettenis
2007-01-05Now that all ethernet drivers that support flow control set MIIF_DOPAUSE,Mark Kettenis
2006-12-31Bring last few phys into line by calling their XXX_status() functionsKenneth R Westerback
2006-12-30Set MASTER based on IFM_ETH_MASTER instead of LINK0.Mark Kettenis
2006-12-30Only advertise flow control if MIIF_DOPAUSE is set.Mark Kettenis
2006-12-30Rewrite eephy(4) to take advantage of generic phy code.Mark Kettenis
2006-12-30Add flow control support.Mark Kettenis
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-19 01:40:20 +0000