summaryrefslogtreecommitdiff
path: root/sys/dev/pci/if_bge.c
AgeCommit message (Expand)Author
2006-10-15recognize the BCM5787 A2 chipset.Brad Smith
2006-10-10revert the firmware synchronization change in rev 1.178, this is the causeBrad Smith
2006-10-09The mickey (/brad) jumbo allocation avoidance patch triggers the sameTheo de Raadt
2006-10-07add a no Ethernet@Wirespeed flag.Brad Smith
2006-10-07add and set PHY workaround flags depending on the ASIC revisionBrad Smith
2006-10-01pack several boolean fields into the existing bge_flags field.Brad Smith
2006-10-01add the PCI ids for the BCM5722, BCM5756, BCM5906 and BCM5906M chipsets.Brad Smith
2006-09-26update the comment for bge_chipinit().Brad Smith
2006-09-26do not alloc jumbo buffers (3.5m per iface) and also do not allow card to rec...Michael Shalayeff
2006-09-17add a flag to indicate which boards are only capable of 10/100 modes ofBrad Smith
2006-09-17Readd the Dell PHY LED setup workaround and the Jumbo capability flag.Brad Smith
2006-09-17- correct the firmware synchronization in bge_reset(), thisBrad Smith
2006-09-17defer establishing the interrupt until later during attach, to let theBrad Smith
2006-09-16Get subvendor from the PROM instead of the PCI configuration space, since theMark Kettenis
2006-08-30Try to read station address from the chip first, then try the EEPROM (if weMark Kettenis
2006-08-29Add support for onboard bge(4)'s on Sun UltraSPARC hardware that apparentlyMark Kettenis
2006-08-28Get MAC address from the OpenFirmware local-mac-address property on sparc64.Mark Kettenis
2006-08-28revert flags usage commits. too close to release. will go in post release ins...Brad Smith
2006-08-28add a BGE_JUMBO flag.Brad Smith
2006-08-28Set the BGE_NO3LED flag to properly adjust the PHY LED mode if attachingBrad Smith
2006-08-27it works a little better like this.Brad Smith
2006-08-27pack several boolean fields into the existing bge_flags field.Brad Smith
2006-08-04move the promiscuous mode handling code into bge_setpromisc() and simplifyBrad Smith
2006-07-01recognize the 5750 C2.Brad Smith
2006-06-29do not return from the reset function if there was a timeoutBrad Smith
2006-06-27don't set BGE_DEBUG by default, reduces the bloat a bit. noticed by deraadt.Brad Smith
2006-06-27Disable Jumbos on the 5714 family of chips for now. The bge driver assumesBrad Smith
2006-06-22recognize the BCM5703 B0.Brad Smith
2006-06-21remove some unused code.Brad Smith
2006-06-21add the BCM5786 PCI id.Brad Smith
2006-06-20have bge_start() check for an empty send queue instead.Brad Smith
2006-06-20- check for revision B2 intead of B1 in one more spot.Brad Smith
2006-06-20add the BCM5755 and BCM5787 ASICs to the appropriate macros.Brad Smith
2006-06-19add the new ASIC revs to the bge_majorrevs table.Brad Smith
2006-06-19add new PCI ids.Brad Smith
2006-06-17add sys/timeout.hBrad Smith
2006-06-15make these tables look a little bit nicer.Brad Smith
2006-06-11the link state detection code should be checking for revision B2 insteadBrad Smith
2006-06-02Deja-vu - again I make bge stop claiming all interrupts for it's own.Bob Beck
2006-05-31xcs -> xscBrad Smith
2006-05-28- remove ETHER_MAX_LEN_JUMBO and ETHERMTU_JUMBO.Brad Smith
2006-05-28unknown ioctl is ENOTTY not EINVALJason Wright
2006-05-27remove IFCAP_JUMBO_MTU interface capabilities flag and set if_hardmtu in a fewBrad Smith
2006-05-20remove commented out and unused capabilities flags.Brad Smith
2006-05-20set if_jumbo_mtu and the IFCAP_JUMBO_MTU capabilities flag whereBrad Smith
2006-05-08KNFBrad Smith
2006-04-30styleBrad Smith
2006-04-24add a missing return here.Brad Smith
2006-04-21recognize the BCM5752 A2Brad Smith
2006-04-05add a power hook for bge(4).Brad Smith
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 15:18:36 +0000