Age | Commit message (Expand) | Author |
2008-07-17 | Add a flag and allow the driver to identify the BCM5788 chipsets. They're | Brad Smith |
2008-07-16 | Enable the read DMA engine's PCI read request burst length long burst | Brad Smith |
2008-04-20 | Add a workaround for a CRC bug errata with BCM5701 A0 and B0 chipset | Brad Smith |
2008-04-03 | Clean up the DMA read/write control register setup code and add some | Brad Smith |
2008-03-02 | Correct the comment describing the BGE_PCISTATE_PCI_BUSSPEED bit. | Brad Smith |
2008-02-20 | When collecting the hardware statistics add the interfaces input errors | Brad Smith |
2008-02-20 | when bge has link, use autopolling for link status, not direct mii polls. | Stuart Henderson |
2008-02-18 | Add initial bits for fiber support with the BCM5714/BCM5715/BCM5780 chipsets. | Brad Smith |
2008-02-02 | - Simplify statistics updates and remove redundant register reads. | Brad Smith |
2008-01-31 | recognize the BCM5755 C0 ASIC revision. | Brad Smith |
2007-11-17 | Rename fiber TBI flag from BGE_TBI to BGE_PHY_FIBER_TBI. No functional change. | Brad Smith |
2007-10-13 | Add support for BCM5906. | Mark Kettenis |
2007-10-11 | Make BGE_JUMBO_FRAMELEN big enough to include vlan tag. Fixes problems with | Mark Kettenis |
2007-02-10 | Add more chipset revision ids. | Kenneth R Westerback |
2007-01-30 | Rough in more support for 5787/5755 chips so far known to not work or | Kenneth R Westerback |
2007-01-10 | Flow control support for bge(4)/brgphy(4). From brad@ based on code from | Mark Kettenis |
2006-12-22 | Remove never used code for a BCM5700 feature (BGE_EXTRAM) that didn't | Kenneth R Westerback |
2006-10-22 | recognize the BCM5715 A3 chipset. | Brad Smith |
2006-10-19 | s/Mhz/MHz/ in comments and printf() strings | Tom Cosgrove |
2006-10-17 | disable the firmware fastboot feature on 5752/5755 and 5787 ASICs, | Brad Smith |
2006-10-15 | recognize the BCM5787 A2 chipset. | Brad Smith |
2006-10-07 | add a no Ethernet@Wirespeed flag. | Brad Smith |
2006-10-07 | add and set PHY workaround flags depending on the ASIC revision | Brad Smith |
2006-10-01 | pack several boolean fields into the existing bge_flags field. | Brad Smith |
2006-10-01 | add the PCI ids for the BCM5722, BCM5756, BCM5906 and BCM5906M chipsets. | Brad Smith |
2006-09-17 | add a flag to indicate which boards are only capable of 10/100 modes of | Brad Smith |
2006-09-17 | Readd the Dell PHY LED setup workaround and the Jumbo capability flag. | Brad Smith |
2006-09-17 | - correct the firmware synchronization in bge_reset(), this | Brad Smith |
2006-08-29 | Add support for onboard bge(4)'s on Sun UltraSPARC hardware that apparently | Mark Kettenis |
2006-08-28 | revert flags usage commits. too close to release. will go in post release ins... | Brad Smith |
2006-08-28 | add a BGE_JUMBO flag. | Brad Smith |
2006-08-28 | Dell PCI vendor subid. | Brad Smith |
2006-08-27 | pack several boolean fields into the existing bge_flags field. | Brad Smith |
2006-08-16 | remove the sparc64 workarounds for the jumbo frame receive ring sizes now | Brad Smith |
2006-07-18 | increase the number of Jumbo slots a little bit for sparc64. | Brad Smith |
2006-07-01 | recognize the 5750 C2. | Brad Smith |
2006-06-22 | recognize the BCM5703 B0. | Brad Smith |
2006-06-19 | some new ASIC revisions. | Brad Smith |
2006-05-28 | - remove ETHER_MAX_LEN_JUMBO and ETHERMTU_JUMBO. | Brad Smith |
2006-04-21 | recognize the BCM5752 A2 | Brad Smith |
2006-04-13 | typo | Brad Smith |
2006-04-05 | add a power hook for bge(4). | Brad Smith |
2006-03-10 | in bge_intr() also check the PCI State register to see if there | Brad Smith |
2006-02-21 | - Overhaul link state detection code. | Brad Smith |
2006-02-11 | recognize another 5714 family chipset. | Brad Smith |
2006-02-01 | some more constants. | Brad Smith |
2006-01-25 | - Count packets discarded by RX/TX MAC (cause of FIFO overflow, etc) | Brad Smith |
2006-01-21 | some cleaning after removing code for reading the VPD. | Brad Smith |
2005-12-28 | eliminate the last few quirk flags. | Brad Smith |
2005-12-12 | If a PCI-X card is detected then set bge_pcix. | Brad Smith |