| Age | Commit message (Expand) | Author |
|---|
| 2010-02-22 | 0x19d2 is most likely a ZTE and not a Qualcomm vendor ID. | Marco Pfatschbacher |
| 2010-02-22 | 0x19d2 is most likely a ZTE and not a Qualcomm vendor ID. | Marco Pfatschbacher |
| 2010-02-22 | Undo 1.48 and 1.49 for now, and go back to the drawing board; PR #6320 | Miod Vallat |
| 2010-02-20 | regen | Jonathan Gray |
| 2010-02-20 | Match on new CH341A in uchcom and correctly name the CH340 device, | Jonathan Gray |
| 2010-02-19 | fix run_set_region_4 to set the whole region specified, | Damien Bergamini |
| 2010-02-18 | do not zero fields which are already zero; from cnst | Theo de Raadt |
| 2010-02-17 | change constant of convert formulra of SHT1X sensor to fit | Yojiro Uo |
| 2010-02-10 | check that rf reg is != 0xff, not rf val. | Damien Bergamini |
| 2010-02-08 | Add ZTE K3565-Z USB MSM modem. | Marco Pfatschbacher |
| 2010-02-08 | sync | Marco Pfatschbacher |
| 2010-02-08 | Add ZTE K3565-Z USB MSM modem. | Marco Pfatschbacher |
| 2010-02-08 | remove redundant bits. | Damien Bergamini |
| 2010-02-08 | final bits for RT3572 and some fixes for RT3070 and RT3071. | Damien Bergamini |
| 2010-02-08 | add the 10us sifs directly to the pre-computed ack durations. | Damien Bergamini |
| 2010-02-08 | simplify | Damien Bergamini |
| 2010-02-08 | s/RT2860_MCU_CMD_BOOT/RT2860_MCU_CMD_RFRESET/ | Damien Bergamini |
| 2010-02-08 | fix BBP R82 for RT3572 | Damien Bergamini |
| 2010-02-07 | writing to RT2860_TX_PIN_CFG requires some extra steps on RT3572 | Damien Bergamini |
| 2010-02-07 | fix my 1.44->1.45 commit | Damien Bergamini |
| 2010-02-07 | we're in 2010. | Damien Bergamini |
| 2010-02-07 | add two more ids for RT3572 and one more id for RT2770. | Damien Bergamini |
| 2010-02-07 | set tx mixer gain for RT3071 | Damien Bergamini |
| 2010-02-07 | change RF init sequence for RT3572 | Damien Bergamini |
| 2010-02-07 | cleanup run_rt3070_set_chan | Damien Bergamini |
| 2010-02-07 | add a function to set the channel on RT3572. | Damien Bergamini |
| 2010-02-07 | when calibrating filter, use better target values for >=RT3071 | Damien Bergamini |
| 2010-02-07 | read vendor RF settings for >=RT3572 and tx mixer gains for >=RT3070 | Damien Bergamini |
| 2010-02-07 | add a new function to set the AGC since the code is a bit different | Damien Bergamini |
| 2010-02-07 | use new mcu command to select the antenna on RT2020 | Damien Bergamini |
| 2010-02-07 | split 32-bit mac_rev into 16-bit mac_ver and mac_rev to avoid | Damien Bergamini |
| 2010-02-07 | add rf init values for rt3572 | Damien Bergamini |
| 2010-02-07 | add channels 167, 169, 171, 173 for dual-band devices | Damien Bergamini |
| 2010-01-26 | sync | Damien Bergamini |
| 2010-01-26 | new run(4) ids | Damien Bergamini |
| 2010-01-21 | Do not assume mac address and bss id are stored at 32-bit aligned addresses; | Miod Vallat |
| 2010-01-15 | sync | Igor Sobrado |
| 2010-01-15 | add `Logitech Webcam C200' to the list of supported uvideo(4) devices. | Igor Sobrado |
| 2010-01-13 | Fix another long standing double scsi_done() bug. This time when a | Kenneth R Westerback |
| 2010-01-09 | Zap all setting of ITSDONE in drivers that don't look at it. Nobody | Kenneth R Westerback |
| 2010-01-09 | Explicitly turn on mii/gmii/rgmii for the 178/gigabit devices | Jonathan Gray |
| 2010-01-06 | sync | Stuart Henderson |
| 2010-01-06 | Add Canon PowerShot SX100, Linksys WUSB600N v2 (new version of RT2870). From ... | Stuart Henderson |
| 2010-01-03 | delete unused variable | Theo de Raadt |
| 2010-01-02 | When finding certain novatel devices in mass storage mode | Jonathan Gray |
| 2009-12-27 | Huawei 180E, from and tested by Bruce O'Neel. | Jonathan Gray |
| 2009-12-27 | regen | Jonathan Gray |
| 2009-12-27 | Huawei E180, from Bruce O'Neel. | Jonathan Gray |
| 2009-12-19 | fix tsleep parameter | Yojiro Uo |
| 2009-12-18 | regen | Yojiro Uo |
