summaryrefslogtreecommitdiff
path: root/sys/dev
AgeCommit message (Expand)Author
2006-03-18probe for it8712 and sis950 (somewhat of a clone)Theo de Raadt
2006-03-18typoBrad Smith
2006-03-18scsi completions never go via the generic done path now. xs is always setDavid Gwynne
2006-03-18use polling for the synchronise command while i move the xs setup andDavid Gwynne
2006-03-18rename ami_cmd to ami_start_xsDavid Gwynne
2006-03-17create a completion path for scsi commands without the cruft for wakingDavid Gwynne
2006-03-17split the completion path up. its now the responsibility of the the pathDavid Gwynne
2006-03-17remove the last remnants of AMI_POLLINGDavid Gwynne
2006-03-16Comment out tekram_sync_table and only degine {,dt_}scf_period[] forMiod Vallat
2006-03-16Move lmc_system_errors[] so that there is only one instance of it in theMiod Vallat
2006-03-16Move the agpgart handling code to a separate file.Matthieu Herrb
2006-03-16if the link is down with a card using a fibre interface then show aBrad Smith
2006-03-16if the link is down then show a media status of none.Brad Smith
2006-03-16tidy up a bit.Brad Smith
2006-03-16sortTheo de Raadt
2006-03-15bits of my tree commited by Matthieu by mistake.Miod Vallat
2006-03-15Remove dead code (SUPPORTS_NON_CONSOLE and MD_DISPLAY_ISA_IOT)Matthieu Herrb
2006-03-15Nuke dk_establish(), no longer used.Miod Vallat
2006-03-15Correct checks against cd_ndevs - valid numbers are strictly inferior toMiod Vallat
2006-03-15Entries in cd_devs[] may be NULL, so be sure to check for them in yourMiod Vallat
2006-03-15switch the ioctl paths to using ami_start instead of ami_cmd. now the onlyDavid Gwynne
2006-03-15clean up ami_start and move the error handling for a failed command fromDavid Gwynne
2006-03-15split the code in ami_cmd that does the polling commands out into aDavid Gwynne
2006-03-15sc->sc_dev.dv_xname converted to DEVNAME(sc). makes things a little easierDavid Gwynne
2006-03-14Return ENXIO when trying to open a non-existent device, not ENODEV.Miod Vallat
2006-03-14move the loading of the dmamaps for passthrough commands out of ami_cmdDavid Gwynne
2006-03-14move the loading of the dma maps for logical disk reads and writes fromDavid Gwynne
2006-03-14knfDavid Gwynne
2006-03-14shuffle the switch statement around in scsi_cmd. do the io commandsDavid Gwynne
2006-03-14a touch of knfDavid Gwynne
2006-03-14add support for the Sony CLIE PEG-T625 and potentially a range of otherDavid Gwynne
2006-03-13Remove unused softc member.Miod Vallat
2006-03-13make the dmseg printing look a little nicer.Brad Smith
2006-03-13RegenMiod Vallat
2006-03-13Conforming to the party's line, report unconfigured devices asMiod Vallat
2006-03-13* Add "pcitag_t *pba_bridgetag" to pci_attach_args. This is set toBrad Smith
2006-03-13Set the address decode bit only if the iobase 0 register is available.Federico G. Schwindt
2006-03-13repair commands w/ no scsi_xfer but the affected code was currently dead anyw...Michael Shalayeff
2006-03-13finner grained use of splbio in scsi_raw_cmd.David Gwynne
2006-03-13finer use of splbio in scsi_cmd.David Gwynne
2006-03-13split the io and synchronise paths for scsi commands going to the logicalDavid Gwynne
2006-03-12regenBrad Smith
2006-03-12some ATI devices.Brad Smith
2006-03-12make SAFE_DEBUG compile clean; ssehic@gmailTheo de Raadt
2006-03-12Make use of pci_matchbyid().Brad Smith
2006-03-12with pcn(4) now in place remove or replace the references to PCI le(4)Martin Reindl
2006-03-12Properly scale voltage on w83l784r.Mark Kettenis
2006-03-12Match emc6d100 and emc6w201. Fix typo. print rev with 0x prefix.Mark Kettenis
2006-03-12Tweak comment.Mark Kettenis
2006-03-12explicitly initialize a couple variablesJacob Meuser