| Age | Commit message (Collapse) | Author |
|---|
|
Makes the code much more robust agains MD paddings. Use new bus.h.
|
|
|
|
valid at that point, and flushing the fifo will hang the system.
|
|
|
|
- integration of Milton Ngan's patch, which provide audio
command support.
..with lots of cleaning up by me.
Audio is still untested. This will change shortly.
|
|
- adjust txhiwat and mindma params a bit
- fixed a couple of incorrectly labeled panic calls
- the "location" was being calculated incorrectly in some cases (forgot
to subtract off MID_RAMBASE). this only caused problem when trying
to change the size of the tx/rx buffers (e.g. to 64KB).
- fixed possible non-aligned DMA burst in the starting byte burst case.
(e.g. if we could DMA 3 bytes, but only have 2 it is not legal
for us to use MIDDMA_BYTE2 mode).
- opt: on tx: try and avoid flushing the internal buffer by padding out the
length of the last mbuf a bit (if possible)
|
|
- alpha changes from cgd
- merged multiple DRQ/DTQ ADD macros into a single DRQ and a single DTQ
macro with a uniform interface to make the code simpler and easier to read.
- en_start: only update atm_flags if EN_MBUF_OPT is enabled (which it
should be)
- for alburst: make sure we don't DMA more bytes than we need (on both
tx and rx). if the alburst is larger than we need, drop to
MIDDMA_WORD mode.
- major change: enable the use of byte and 2 byte DMA on the trasmit side.
this allows us to DMA from non-word sized/aligned mbufs directly.
[the old code would always call en_mfix which would copy (or move) the
data in order to ensure proper alignment... it turns out TCP gives
us non-word sized/aligned mbufs when it is retransmitting, so we needed
to handle this case more efficiently.] the following functions
were changed to make this work:
- en_dqneed: add an arg to let us know if we are transmitting or not.
if we are TX, then we must take into account byte DMAs when
estimating the number of DTQs we will need for a buffer
- en_start: only mfix mbufs if DMA is disabled
- en_txdma: only set launch.nodma if we have en_mfix'd the mbuf chain
also, we may need a DTQ to flush the chip's internal byte buffer
- en_txlaunch: only attempt a copy if we have the proper alignment.
add byte dma code for the front and end of the buffer.
make sure the internal dma buffer is flushed out.
- en_dump: keep track of how many times we have to use byte sized DMA
midwayreg:
- add byte/2byte DMA defines
midwayvar:
- add new stat counter to monitor less-than-word lengthed DMA
|
|
- en_mfix shouldn't touch M_EXT mbufs. change to avoid this [at
the expense of allocating a new cluster mbuf to copy to].
XXX: en_mfix is getting called more often than I hoped it would
(seems to happen when TCP retransmits... we get all sorts of odd
sized, odd lengthed data mbufs, yuck). i may revise the xmit
DMA code to use non-word sized dma.
|
|
- don't try and add a PDU trailer (or TBD for that matter) to an M_EXT
mbuf. when M_EXT is set, the data area of the mbuf can be shared
with other mbufs (see m_copym()), and writing to one M_EXT mbuf may
invalidate another M_EXT mbuf (saw this with PDU trailers).
- be sure to validate the length value from the PDU trailer so that it
doesn't throw us out of sync with the chip (fixes yet another source
of the dread "en_service: id mismatch" panic).
- on recv, don't bother allocating an mbuf if mlen is zero since we are
only going to toss the data anyway.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
on port-i386@netbsd.org.
|
|
to ignore inbound data sizes less than the threshold. otherwise,
when connected to a video aal0 input the driver gives us a massive
stream of 56 byte mbufs each with one aal0 cell in it and the
system just can't keep up with it, especially if the socket buffer
size is large [it hangs until you turn off the video source].
fixes: when turning off a vc, try and check the freshest copy of the mode
when seeing if we need to enter the "drain" state. also, don't
panic if we get unexpected rx interrupt on a VCI (instead make sure
the VC is off, print a warning, and move on!).
|
|
- change rxso into a void handle ... no need to know details at this low
level.
fix:
- forgot to init "vci" during ENOTHER_DRAIN case of RX DMA interrupt
[could cause a vm_fault on native mode connection close depending
on needing to drain out the VC and also the random value of vci]
|
|
|
|
|
|
|
|
- more stat counters (rxmbufout -- mbufs, ttrash -- trashed RBD)
- add swsl_size to keep track of size of software slist
- revise when we call en_service
- fix handling of circular lists (was getting full vs empty confused in
extreem cases...)
- native mode atm: remove sbappend code: can't do it here since
socket buffer is protected only by splsoftnet and that doesn't
mask enintr off. forces us to switch to a two level interrupt
scheme. revise call to atm_input to reflect that.
|
|
|
|
[1] rxslot "cur" pointer wasn't updated if we copied all data and
didn't have any fill. this could cause a service id mismatch
panic under load.
[2] recv of aal0 forgot to include the cell header in the data length
calc [add cell header length to midwayreg.h]
[3] fix control info "chop" for raw mode and aal0
[4] handle rxsb better for native atm connections
(XXX: still working on this ... not complete and needs revision)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
patches taken from jtk's dosemu for NetBSD 1.1 and updated for
the current driver. Some of the code is based an older FreeBSD
version of the driver.
|
|
have wasted weeks because of the crashes.
|
|
Enable reselections as soon as possible after a disconnect - prevents
losing a reselecting device.
Check for and ignore a spurious interrupt during a DMA input (from the
Mach driver).
|
|
|
