| Age | Commit message (Collapse) | Author |
|---|
|
ok marco
|
|
way, rather than requiring some glue in each machines mainbus probe.
it is still commented out.
based on a discussion with miod@ ok marco@ deraadt@
|
|
implementation of a RAID 1 is included in this but it does not deal with
failures yet. Disabled in GENERIC.
Suggestions from and ok beck@ miod@ krw@ dlg@ deraadt@
|
|
BCM5756). They still don't work but when they do they won't use an
inappropriate Jitter bug workaround. No effect on other chips.
From Michael Chan of Broadcom, via Linux tg3 via Brad.
ok reyk@
|
|
|
|
controllers don't. Put in a temporary hack for pxammc on Zaurus.
|
|
We use the suggested workaround for the problem E40 in the PXA27x errata
sheet. Unfortunately this limits the bus speed to 9.75Mhz.
|
|
time.
Chris; Get your shiz fixed and tested for the next time. We have
better todo then wasting our time by backing out untested stuff.
OK deraadt, OK ckuethe
|
|
|
|
|
|
|
|
http://bcm-specs.sipsolutions.net/80211Init.
o Add a rewritten version of bcw_core_reset() called bcw_80211_core_reset()
according to http://bcm-specs.sipsolutions.net/80211CoreReset. This
will probably replace bcw_core_reset(), but I need more verification
first.
o Add bcw_core_enable() and bcw_core_disable(). There seems to be
devices which contain several 802.11 cores. The unused needs to be
disabled.
|
|
but defer the remainder of their initialisation until after the other devices
on their PCI bus have attached. This ensures that any USB2 controller has also
completed its initialisation before we start to initialise the USB1 parts.
This minimises the chance that a nasty SMM implementation will trash the USB1
controller's config when it performs legacy emulation handover of the USB2 part.
|
|
and defer the delay for root hubs until the host controller event thread
starts, permitting some concurrency. Speeds up the boot process dramatically
when you have lots of host controllers.
ok dlg@
|
|
reset, rather than at suspend/resume, otherwise any BIOS inserted value
is lost immediately.
ok dlg@
|
|
|
|
reported by brad
|
|
one for all SPI controllers. krw has a sun machine with a 1030 that gets
the bus width wrong too, so since vmware emulates that type of hardware
too, we can just limit the lot of them and forget about it.
|
|
|
|
|
|
From Eric Gillingham <sysrq@sysrq.tk>
|
|
called bcw_chip_init(), according to the 80211Init steps in the spec.
|
|
currently the driver only support touchscreens made by eGalax and
Future Technology Devices (ITM)
ok deraadt@
|
|
|
|
|
|
copied over from bce(4) and is obsolete or needs to be rewritten.
|
|
|
|
fill everything up to IEEE80211_ELEMID_TIM into the beacon template and
everything after and including IEEE80211_ELEMID_TIM into the tim template.
This fixes the beacons on 11g where two TIM fields where announced.
acx_beacon_locate() is used to calculate the offset to a defined TLV field.
If other dirvers need it as well we may move it up into net80211.
OK mglocker@
|
|
remove lots of obsolete registers, mark unused registers for deletion,
mark suspect registers for closer verification, comments ...
|
|
|
|
|
|
|
|
interrupts at some point.
|
|
it's a good idea to use atomic.h operations on it. This mechanic
change updates all bit operations on p_flag to atomic_{set,clear}bits_int.
Only exception is that P_OWEUPC is set by MI code before calling
need_proftick and it's automatically cleared by ADDUPC. There's
no reason for MD handling of that flag since everyone handles it the
same way.
kettenis@ ok
|
|
|
|
|
|
|
|
|
|
|
|
ieee80211_input() enqueued a packet beforehand. malo(4) does not support
hostap mode so this should not happen but perhaps mglocker@ gets it working
someday. OK mglocker@
|
|
calling if_start(). So call ifp->if_start() at the end of the RX interrupt
function. This solves the porblem of getting dhcp leases from the AP if the
network is quiet. OK mglocker@
|
|
while there, remove explicit global variable initializations to zero,
and appease the gods by removing the most ludicrous spurious casts.
No functional change (except for code shrinkage).
|
|
really using 24 bpp pixels on 32 bit boundaries.
|
|
|
|
|
|
|
|
|
|
help and ok krw@
|
|
register (typo).
|
|
|
