| Age | Commit message (Expand) | Author |
|---|
| 2010-02-11 | No need for M_CANFAIL if M_NOWAIT is used. Found by Gleydson Soares. | Claudio Jeker |
| 2010-02-10 | Only allow the common voltages of the card and the host when writing the OCR | Dale Rahn |
| 2010-02-10 | check that rf reg is != 0xff, not rf val. | Damien Bergamini |
| 2010-02-09 | Build ral firmware on loongson (for Gdium). | Miod Vallat |
| 2010-02-09 | XY Failure reads no longer require temp buffer or WUF_FAIL | Jordan Hargrave |
| 2010-02-08 | Use character raw device to read disklabel during bootprobe, as all | Kenneth R Westerback |
| 2010-02-08 | Add ZTE K3565-Z USB MSM modem. | Marco Pfatschbacher |
| 2010-02-08 | sync | Marco Pfatschbacher |
| 2010-02-08 | Add ZTE K3565-Z USB MSM modem. | Marco Pfatschbacher |
| 2010-02-08 | remove redundant bits. | Damien Bergamini |
| 2010-02-08 | final bits for RT3572 and some fixes for RT3070 and RT3071. | Damien Bergamini |
| 2010-02-08 | add the 10us sifs directly to the pre-computed ack durations. | Damien Bergamini |
| 2010-02-08 | simplify | Damien Bergamini |
| 2010-02-08 | s/RT2860_MCU_CMD_BOOT/RT2860_MCU_CMD_RFRESET/ | Damien Bergamini |
| 2010-02-08 | fix BBP R82 for RT3572 | Damien Bergamini |
| 2010-02-08 | When initialising the chip actually set the hardware MAC address, thus | Joel Sing |
| 2010-02-07 | regen | Mark Kettenis |
| 2010-02-07 | Add VIA VT8251 AHCI. | Mark Kettenis |
| 2010-02-07 | writing to RT2860_TX_PIN_CFG requires some extra steps on RT3572 | Damien Bergamini |
| 2010-02-07 | fix my 1.44->1.45 commit | Damien Bergamini |
| 2010-02-07 | HT is not enable so skip this. | Damien Bergamini |
| 2010-02-07 | we're in 2010. | Damien Bergamini |
| 2010-02-07 | add two more ids for RT3572 and one more id for RT2770. | Damien Bergamini |
| 2010-02-07 | set default value for BBP R106 | Damien Bergamini |
| 2010-02-07 | set tx mixer gain for RT3071 | Damien Bergamini |
| 2010-02-07 | change RF init sequence for RT3572 | Damien Bergamini |
| 2010-02-07 | cleanup run_rt3070_set_chan | Damien Bergamini |
| 2010-02-07 | add a function to set the channel on RT3572. | Damien Bergamini |
| 2010-02-07 | when calibrating filter, use better target values for >=RT3071 | Damien Bergamini |
| 2010-02-07 | read vendor RF settings for >=RT3572 and tx mixer gains for >=RT3070 | Damien Bergamini |
| 2010-02-07 | add a new function to set the AGC since the code is a bit different | Damien Bergamini |
| 2010-02-07 | use new mcu command to select the antenna on RT2020 | Damien Bergamini |
| 2010-02-07 | split 32-bit mac_rev into 16-bit mac_ver and mac_rev to avoid | Damien Bergamini |
| 2010-02-07 | add rf init values for rt3572 | Damien Bergamini |
| 2010-02-07 | update firmware for rt2870 and >=rt3071 | Damien Bergamini |
| 2010-02-07 | add channels 167, 169, 171, 173 for dual-band devices | Damien Bergamini |
| 2010-02-05 | regen | Miod Vallat |
| 2010-02-05 | Add SiliconMotion Voyager GX, reportedly found in Gdium Liberty. | Miod Vallat |
| 2010-02-05 | regen | Jasper Lievisse Adriaanse |
| 2010-02-05 | - fix doubles | Jasper Lievisse Adriaanse |
| 2010-02-05 | regen | Jasper Lievisse Adriaanse |
| 2010-02-05 | - add few new devices found in dmesglog | Jasper Lievisse Adriaanse |
| 2010-02-04 | Added optimization for XY reads, requires only one temp buffer | Jordan Hargrave |
| 2010-02-04 | Optimized failure handing for Read with X/P failures | Jordan Hargrave |
| 2010-02-03 | init ofdm sensitivity with min value (which depends on the chip) | Damien Bergamini |
| 2010-02-03 | Enable the next page bit for IP1001, otherwise the PHY fails | Stuart Henderson |
| 2010-02-03 | Use nitems. | Joel Sing |
| 2010-02-02 | Attach athn(4) to the AR2427 which is a castrated (no 11n) AR928X. | Damien Bergamini |
| 2010-02-02 | regen | Damien Bergamini |
| 2010-02-02 | add AR2427 pci id | Damien Bergamini |
