| Age | Commit message (Expand) | Author |
|---|
| 2017-01-31 | In a comment inside ieee80211_up_to_ac(), update a reference section | Stefan Sperling |
| 2017-01-31 | When telling clients which EDCA parameters to use, copy these parameters | Stefan Sperling |
| 2017-01-30 | Enable ieee80211_edca_table, which was under #if 0. This table can be used | Stefan Sperling |
| 2017-01-28 | Make mira cope with out-of-range single frame error rate (SFER) values. | Stefan Sperling |
| 2017-01-28 | Introduce ieee80211_mira_probe_done() helper which resets probing state, | Stefan Sperling |
| 2017-01-25 | In amsdu_decap() check the actual length of the data in the remaining mbuf | Stefan Sperling |
| 2017-01-19 | Enable TKIP as pairwise cipher when ifconfig's wpaprotos option enables WPA1. | Stefan Sperling |
| 2017-01-16 | Reset block ack state and cancel related timeouts when a HT node disassociates. | Stefan Sperling |
| 2017-01-16 | Prevent wireless frame injection attack described at 33C3 in the talk | Stefan Sperling |
| 2017-01-12 | Rename ieee80211_mira_node_destroy() to ieee80211_mira_cancel_timeouts(). | Stefan Sperling |
| 2017-01-10 | Make receiving A-MPDUs with an 11n-enabled athn(4) driver work by not | Stefan Sperling |
| 2017-01-09 | When a HT node leaves or reassociates as a non-HT node, | Stefan Sperling |
| 2017-01-09 | Stop defining MIRA_DEBUG by default. | Stefan Sperling |
| 2017-01-09 | Show node MAC addresses in mira debug output. | Stefan Sperling |
| 2017-01-09 | Make the net80211 stack send EDCA parameters to the driver in hostap mode. | Stefan Sperling |
| 2017-01-09 | When acting as 11n hostap, send Microsoft WME parameters to clients so | Stefan Sperling |
| 2017-01-09 | Manage the HT protection setting if acting as hostap with 11n enabled. | Stefan Sperling |
| 2017-01-09 | The point of ieee80211_node_leave() is to place the node in COLLECT state. | Stefan Sperling |
| 2017-01-09 | When acting as hostap, negotiate HT before calling the driver's ic_newassoc() | Stefan Sperling |
| 2017-01-09 | Fix ieee80211_add_htop(), which is not yet called in active code paths. | Stefan Sperling |
| 2016-12-31 | When we disable WPA on an interface, wipe all of the WPA parameters, | Peter Hessler |
| 2016-12-26 | Allow using 11n mode with APs that do not advertise support for all of MCS 0-7. | Stefan Sperling |
| 2016-12-26 | When calculating the set of MCS rates below a particular MCS, skip rates | Stefan Sperling |
| 2016-12-20 | Disable TKIP (WPA1) by default. | Stefan Sperling |
| 2016-12-18 | While copying out channel flags to userspace, omit the HT channel flag if | Stefan Sperling |
| 2016-12-18 | Set the maximum TKIP countermeasure timeout to 90 seconds instead of 120. | Stefan Sperling |
| 2016-12-17 | Don't crash while sending a TKIP MIC failure report to the AP. | Stefan Sperling |
| 2016-12-17 | Complete our half-done implementation of TKIP countermeasures in hostap mode. | Stefan Sperling |
| 2016-12-10 | Make mira rate scaling actually work with MIMO Tx rates. | Stefan Sperling |
| 2016-12-08 | Fix mira's next intra-rate calculations for MCS >= 8. | Stefan Sperling |
| 2016-12-06 | avoid a potentially uninitialised return value | Jonathan Gray |
| 2016-11-30 | Add a new implementation of MiRA, a rate scaling algorithm for 802.11n. | Stefan Sperling |
| 2016-10-08 | Allow writing an MCS index to radiotap's rate field. The format we use is | Stefan Sperling |
| 2016-09-21 | When processing an ADDBA request, iwm(4) runs a task which sends a | Stefan Sperling |
| 2016-09-20 | Parse the DTIM count and period advertised in beacons and store them | Stefan Sperling |
| 2016-09-15 | move from RB macros to the RBT functions. | David Gwynne |
| 2016-08-31 | If a driver reports RSSI in the 20-100 range, convert to a negative value. | Stefan Sperling |
| 2016-08-17 | If a wireless device or driver scans all bands at once give 5GHz APs | Stefan Sperling |
| 2016-08-15 | Expose more 802.11n information to userspace: | Stefan Sperling |
| 2016-07-20 | In net80211, enable RTS for frames above a particular size (currently 512 | Stefan Sperling |
| 2016-05-21 | Add a wireless driver capability flag for devices which scan 2GHz and 5GHz | Stefan Sperling |
| 2016-05-18 | In hostap mode, don't re-use association IDs (AIDs) of nodes which are | Stefan Sperling |
| 2016-05-12 | Fix "comma at end of enumerator list" warnings | David Coppa |
| 2016-05-10 | make bpf_mtap callers set the M_FILDROP flag if they care about it. | David Gwynne |
| 2016-05-02 | Fix a corner case of 12-bit arithmetic: also increment the ba_winmiss | Theo Buehler |
| 2016-05-02 | IEEE 802.11 sequence numbers wrap at 12 bit. | Stefan Sperling |
| 2016-04-28 | Rework handling of frames which fall beyond the block ack window. | Stefan Sperling |
| 2016-04-28 | Add a net80211 stat counter for block ack window "slides" as opposed | Stefan Sperling |
| 2016-04-28 | When a frame which falls into the block ack window is received, clear | Stefan Sperling |
| 2016-04-28 | Copy some ieee8021_node HT information to userspace. | Stefan Sperling |
