| Age | Commit message (Expand) | Author |
|---|
| 2006-06-01 | SDIO card identification | Uwe Stuehler |
| 2006-06-01 | fewer debug messages | Uwe Stuehler |
| 2006-06-01 | Right at the end of a debug kernel build, the current Makefile copies bsd | Christopher Pascoe |
| 2006-06-01 | regen | Uwe Stuehler |
| 2006-06-01 | The Spectec device is probably a SDW-820. Keep product names short | Uwe Stuehler |
| 2006-06-01 | leave the reply_dva address alone so we can post it back to the ioc rather | David Gwynne |
| 2006-06-01 | latch the AFSR/AFAR -before- reading the PCI control/status register | Jason Wright |
| 2006-06-01 | regen | Uwe Stuehler |
| 2006-06-01 | Start a list of SD vendors and products. | Uwe Stuehler |
| 2006-06-01 | do a better job of setting up the PBM. Doesn't fix the PIO faults we're | Jason Wright |
| 2006-06-01 | Add basic NMEA0183 support as a tty line discipline. The line discipline | Marc Balmer |
| 2006-06-01 | fix some macros | David Gwynne |
| 2006-06-01 | - stop using magic constants for the onboard error INOs (one was wrong anyway) | Jason Wright |
| 2006-06-01 | Compile broken ipmi into GENERIC, so it's easy for marco to fix | Bob Beck |
| 2006-06-01 | After changing J3 to J4 on the thecus board, serial interrupts work just | Dale Rahn |
| 2006-06-01 | Splraise is strictly to increase spl, do not lower. | Dale Rahn |
| 2006-06-01 | Better to attach obio devices after pci. | Dale Rahn |
| 2006-06-01 | Proper config attach, not always return 1 from probe. | Dale Rahn |
| 2006-06-01 | Make the debug printfs work if RAL_DEBUG is defined. | Robert Nagy |
| 2006-06-01 | Add powerhooks for ral(4) cards with RT2561 chipset, and also fix | Robert Nagy |
| 2006-06-01 | add 2 subclasses, subclass storage SAS and subclass system SD Host Controller. | Brad Smith |
| 2006-06-01 | enable xge(4) on the CD RAMDISKs. | Brad Smith |
| 2006-06-01 | de-static and formatting. | Brad Smith |
| 2006-06-01 | enable hardware RX checksum offload. | Brad Smith |
| 2006-06-01 | formatting | Brad Smith |
| 2006-06-01 | add bit defns for [UE]FAR | Jason Wright |
| 2006-06-01 | Correct IRQ mappings for thecus devices. | Dale Rahn |
| 2006-06-01 | current_ipl_level is a value, not a mask, do not '|=' into it. | Dale Rahn |
| 2006-06-01 | enable error interrupts and install handlers for same (the handlers don't do ... | Jason Wright |
| 2006-06-01 | observed by Naddy, found by claudio, strange constructs require strange defines | Todd T. Fries |
| 2006-06-01 | CACHE_GLOBAL is enforced at the APR level, no need to propagate it into | Miod Vallat |
| 2006-06-01 | Better test for cacheability of the previous mapping in pmap_cache_ctrl() | Miod Vallat |
| 2006-06-01 | Change spl4() to spl7() to raise-only semantics. | Miod Vallat |
| 2006-06-01 | oops, i dont know how to count bits. fix the OFFSET bitmasks in the device | David Gwynne |
| 2006-06-01 | add spi device configuration pages 0 and 1 | David Gwynne |
| 2006-06-01 | We do not create st devices with different density modes. i.e. with device | Kenneth R Westerback |
| 2006-06-01 | Add the MIIF_AUTOTSLEEP flag, needed by gigabit axe(4) devices. | Christopher Pascoe |
| 2006-06-01 | use the table ID as array index directly, faster in the forwarding path | Henning Brauer |
| 2006-06-01 | Remove unused macros, improve readability. | Christopher Pascoe |
| 2006-06-01 | Make umv_pglistalloc() return EINVAL if it is asked for 0 bytes. This | Kenneth R Westerback |
| 2006-06-01 | fix the reply handling on crazy machines that give me bits in the high part | David Gwynne |
| 2006-06-01 | Pass the value of IPG2 to the AX88178 in the index register. | Christopher Pascoe |
| 2006-06-01 | KNF. | Christopher Pascoe |
| 2006-06-01 | Whitespace cleanup. | Christopher Pascoe |
| 2006-06-01 | Consistantly map com0 irq. | Dale Rahn |
| 2006-06-01 | Just say NO to noisy dmesg. | Dale Rahn |
| 2006-06-01 | IO addresses will always be in the right range, this check is wrong. | Dale Rahn |
| 2006-06-01 | Just say no to noisy dmesg. | Dale Rahn |
| 2006-06-01 | Now that this maps correctly, allow the interrupt to map properly. | Dale Rahn |
| 2006-06-01 | Properly remap I/O Addresses for theucs/IOData boxes. | Dale Rahn |
