| Age | Commit message (Expand) | Author |
|---|
| 2010-02-09 | - add the whole gang of USB devices; as prompted by deraadt@ | Jasper Lievisse Adriaanse |
| 2010-02-09 | Fix off-by-one system control register defines, makes 2D acceleration on | Miod Vallat |
| 2010-02-09 | XY Failure reads no longer require temp buffer or WUF_FAIL | Jordan Hargrave |
| 2010-02-08 | Use character raw device to read disklabel during bootprobe, as all | Kenneth R Westerback |
| 2010-02-08 | Add ZTE K3565-Z USB MSM modem. | Marco Pfatschbacher |
| 2010-02-08 | sync | Marco Pfatschbacher |
| 2010-02-08 | Add ZTE K3565-Z USB MSM modem. | Marco Pfatschbacher |
| 2010-02-08 | remove redundant bits. | Damien Bergamini |
| 2010-02-08 | final bits for RT3572 and some fixes for RT3070 and RT3071. | Damien Bergamini |
| 2010-02-08 | Add ral(4), found on the Gdium Liberty 1000. | Miod Vallat |
| 2010-02-08 | Minimal completion support for .l.s and .l.d routines, necessary for at | Miod Vallat |
| 2010-02-08 | add the 10us sifs directly to the pre-computed ack durations. | Damien Bergamini |
| 2010-02-08 | simplify | Damien Bergamini |
| 2010-02-08 | s/RT2860_MCU_CMD_BOOT/RT2860_MCU_CMD_RFRESET/ | Damien Bergamini |
| 2010-02-08 | fix BBP R82 for RT3572 | Damien Bergamini |
| 2010-02-08 | The IMPs are history so is splimp, this needs now splnet so update comment. | Claudio Jeker |
| 2010-02-08 | arpioctl() is not used sore remove it. Found by Gleydson Soares. | Claudio Jeker |
| 2010-02-08 | When initialising the chip actually set the hardware MAC address, thus | Joel Sing |
| 2010-02-08 | More destatic and ansification. | Joel Sing |
| 2010-02-08 | More destatic and ansification. | Joel Sing |
| 2010-02-08 | Destatic and ansify. | Joel Sing |
| 2010-02-08 | Destatic and ansify. | Joel Sing |
| 2010-02-07 | Fix machine tag. | Dale Rahn |
| 2010-02-07 | Beagle has two memory banks, fix buffer overflow. | Dale Rahn |
| 2010-02-07 | regen | Mark Kettenis |
| 2010-02-07 | Add VIA VT8251 AHCI. | Mark Kettenis |
| 2010-02-07 | writing to RT2860_TX_PIN_CFG requires some extra steps on RT3572 | Damien Bergamini |
| 2010-02-07 | fix my 1.44->1.45 commit | Damien Bergamini |
| 2010-02-07 | HT is not enable so skip this. | Damien Bergamini |
| 2010-02-07 | we're in 2010. | Damien Bergamini |
| 2010-02-07 | add two more ids for RT3572 and one more id for RT2770. | Damien Bergamini |
| 2010-02-07 | set default value for BBP R106 | Damien Bergamini |
| 2010-02-07 | set tx mixer gain for RT3071 | Damien Bergamini |
| 2010-02-07 | change RF init sequence for RT3572 | Damien Bergamini |
| 2010-02-07 | cleanup run_rt3070_set_chan | Damien Bergamini |
| 2010-02-07 | add a function to set the channel on RT3572. | Damien Bergamini |
| 2010-02-07 | when calibrating filter, use better target values for >=RT3071 | Damien Bergamini |
| 2010-02-07 | read vendor RF settings for >=RT3572 and tx mixer gains for >=RT3070 | Damien Bergamini |
| 2010-02-07 | add a new function to set the AGC since the code is a bit different | Damien Bergamini |
| 2010-02-07 | use new mcu command to select the antenna on RT2020 | Damien Bergamini |
| 2010-02-07 | split 32-bit mac_rev into 16-bit mac_ver and mac_rev to avoid | Damien Bergamini |
| 2010-02-07 | add rf init values for rt3572 | Damien Bergamini |
| 2010-02-07 | update firmware for rt2870 and >=rt3071 | Damien Bergamini |
| 2010-02-07 | add channels 167, 169, 171, 173 for dual-band devices | Damien Bergamini |
| 2010-02-06 | when receiving the first message of an rsn group key handshake | joshua stein |
| 2010-02-05 | Now that the BTB errata are out of the way, enable the CS5536 timecounter again, | Miod Vallat |
| 2010-02-05 | add uaudio; ok miod@ | Otto Moerbeek |
| 2010-02-05 | Blind support for SM501 model. This should give the Gdium Liberty a working, | Miod Vallat |
| 2010-02-05 | regen | Miod Vallat |
| 2010-02-05 | Add SiliconMotion Voyager GX, reportedly found in Gdium Liberty. | Miod Vallat |
