From 28c50a073408e43d50310d8c0bb405461cfbccc7 Mon Sep 17 00:00:00 2001 From: Miod Vallat Date: Sat, 30 Mar 2002 22:52:59 +0000 Subject: Factorize more common texts from the ramdisk operation. No text changes except for harmonization, and the blurb about network interface flags has bene slightly changed for some arches. --- distrib/notes/i386/install | 99 +++++----------------------------------------- 1 file changed, 10 insertions(+), 89 deletions(-) (limited to 'distrib/notes/i386/install') diff --git a/distrib/notes/i386/install b/distrib/notes/i386/install index bf6beb819c8..728309c1d3b 100644 --- a/distrib/notes/i386/install +++ b/distrib/notes/i386/install @@ -1,3 +1,4 @@ +dnl $OpenBSD: install,v 1.33 2002/03/30 22:52:57 miod Exp $ OpenBSDInstallPrelude If OpenBSD will be sharing the disk with DOS or another operating @@ -39,18 +40,7 @@ OpenBSDBootMsgs You will next be asked for your terminal type. You should just hit return to select the default (vt220). - Now you will be asked whether you wish to do an "install" - or an "upgrade". Enter 'i' for a fresh install or 'u' to - upgrade an existing installation. - - You will be presented with a welcome message and asked if - you really wish to install (or upgrade). - - The install program will then tell you which disks of that - type it can install on, and ask you which it should use. The - name of the disk is typically "wd0" for IDE/RLL/ESDI/ST506 - drives or "sd0" for SCSI drives. Reply with the name of your - disk. +OpenBSDInstallPart3({:- or "wd0" for IDE/RLL/ESDI/ST506 drives-:}) Next you will have to edit or create a disk label for the disk OpenBSD is being installed on. If there are any existing @@ -66,30 +56,9 @@ OpenBSDBootMsgs correct this. Note that you should make OpenBSD be the active partition at least until the install has been completed. - Next the disk label which defines the layout of the OpenBSD - file systems must be set up. The installation script will - invoke an interactive editor allowing you to do this. Note - that partition 'c' inside this disk label should ALWAYS - reflect the entire disk, including any non-OpenBSD portions. - If you are labeling a new disk, you will probably start - out with an 'a' partition that spans the disk. In this case - You should delete 'a' before adding new partitions. - The root file system should be in partition 'a', and swap - is usually in partition 'b'. If you have DOS or Linux - partitions defined on the disk, these will usually show up - as partition 'h', 'i' and so on. It is recommended that - you create separate partitions for /usr, /tmp, and /var, and - if you have room for it, one for /home. In doing this, remember - to skip 'c', leaving it as type "unused". Create your next - partition as 'd' and continue from there with any additional - partitions. If you have DOS or Linux partitions defined on the - disk, these will usually show up as partition 'h', 'i', and - so on. - - When you are finished with disklabel you will be prompted for - the mount points for the partitions in the current label. - For help in the disk label editor, enter '?' or 'M' to view - the manual page (see the info on the ``-E'' flag). +OpenBSDInstallPart4({:- If you have DOS or Linux partitions + defined on the disk, these will usually show up as partition + 'h', 'i' and so on.-:}) Note that all OpenBSD partitions in the disk label must have an offset that makes it start within the OpenBSD part of the disk, @@ -98,65 +67,17 @@ OpenBSDBootMsgs shared with other operating systems, and within the OpenBSD fdisk partition if the disk is being shared. - The swap partition (usually 'b') should have a type of "swap", all - other native OpenBSD partitions should have a type of "4.2BSD". - Block and fragment sizes are usually 8192 and 1024 bytes, but can - also be 4096 and 512 or even 16384 and 2048 bytes. - - The install program will now label your disk and ask which file - systems should be created on which partitions. It will auto- - matically select the 'a' partition to be the root file system. - Next it will ask for which disk and partition you want a file - system created on. This will be the same as the disk name (e.g. - "wd0") with the letter identifying the partition (e.g. "d") - appended (e.g. "wd0d"). Then it will ask where this partition is - to be mounted, e.g. /usr. This process will be repeated until - you enter "done". - - At this point you will be asked to confirm that the file system - information you have entered is correct, and given an opportunity - to change the file system table. Next it will create the new file - systems as specified, OVERWRITING ANY EXISTING DATA. This is the - point of no return. - - After all your file systems have been created, the install program - will give you an opportunity to configure the network. The network - configuration you enter (if any) can then be used to do the install - from another system using HTTP or FTP, and will also be the - configuration used by the system after the installation is complete. - - If you select to configure the network, the install program will - ask you for a name of your system and the DNS domain name to use. - Note that the host name should be without the domain part, and that - the domain name should NOT {:-include-:} the host name part. - - Next the system will give you a list of network interfaces you can - configure. For each network interface you select to configure, it - will ask for the IP address to use, the symbolic host name to use, - the netmask to use and any interface-specific flags to set. The - interface-specific flags are usually used to determine which media - the network card is to use. The flags usually carry the following +OpenBSDInstallPart5(wd0) + +OpenBSDInstallNet(linkflags)dnl + The flags usually carry the following meaning: -link0 -link1 Use BNC (coaxial) port [default] link0 -link1 Use AUI port link0 link1 Use UTP (twisted pair) port - After all network interfaces have been configured the install pro- - gram will ask for a default route and IP address of the primary - name server to use. You will also be presented with an opportunity - to edit the host table. - - At this point you will be allowed to edit the file system table - that will be used for the remainder of the installation and that - will be used by the finished system, following which the new file - systems will be mounted to complete the installation. - - After these preparatory steps have been completed, you will be - able to extract the distribution sets onto your system. There - are several install methods supported; FTP, HTTP, tape, CD-ROM, - or a local disk partition. Note that installation from floppies - is not currently supported. +OpenBSDInstallNet2({:-CD-ROM, -:},nofloppy) OpenBSDFTPInstall -- cgit v1.2.3