OpenBSDInstallPrelude OpenBSDInstallPart2 If you are using the floppy{:--:}OSrev.fs floppy, type "boot dva0" and hit return when presented with the SRM console prompt. You should see info about the primary and secondary boot and then the kernel should start to load. It will take a while to load the kernel from the floppy, most likely more than a minute. If some action doesn't eventually happen, or the spinning cursor has stopped and nothing further has happened, either your boot floppy is bad or you are having hardware problems. Either you have a bad boot floppy (in which case you should try another) or your alpha is not currently supported by OpenBSD. If you are booting from the CD-ROM, type "show device" and hit return when presented with the SRM console prompt. You should see a list of devices; the SCSI devices will start with "DKA". Find the SCSI device that is your CD-ROM and enter "boot dka4 -fi OSREV/alpha/bsd", assuming that your CD-ROM was listed as DKA4* (substitute the SCSI id of your CD-ROM for the "4"). You should see info about the primary and secondary boot and then the kernel should start to load. If the kernel fails to load or the spinning cursor has stopped and nothing further has happened, you either have a hardware problem or your alpha is not currently supported by OpenBSD; try booting from a floppy instead. OpenBSDBootMsgs While booting, you will probably see several warnings. You should be warned that the kernel can't figure out what device it booted from and that no swap space is present. Do not be alarmed, these are completely normal. The first warning occurs because while OpenBSD/alpha can boot from the floppy drive, the kernel itself lacks a floppy driver. When you reach the prompt asking you for a shell name, just hit return. You will next be asked for your terminal type. If you are installing from a non-serial console, the default of "sun" is correct. If you are installing from a serial console you should choose the terminal type from amongst those listed. (If your terminal type is xterm, just use vt100). After entering the terminal type you will be asked whether you wish to do an "install" or an "upgrade". Enter 'i' for a fresh install or 'u' to upgrade an existing installation. You will be presented with a welcome message and asked if you really wish to install (or upgrade). Assuming you answered yes, the install program will then tell you which disks of that type it can install on, and ask you which it should use. The name of the disk is typically "sd0" for SCSI drives or "wd0" for IDE drives. Reply with the name of your disk. Next the disk label which defines the layout of the OpenBSD file systems must be set up. The installation script will invoke an interactive editor allowing you to do this. Note that partition 'c' inside this disk label should ALWAYS reflect the entire disk, including any non-OpenBSD portions. If you are labeling a new disk, you will probably start out with an 'a' partition that spans the disk. In this case You should delete 'a' before adding new partitions. The root file system should be in partition 'a', and swap is usually in partition 'b'. It is recommended that you create separate partitions for /usr and /var, and if you have room for it, one for /home. For help in the disk label editor, enter '?' or 'M' to view the manual page (see the info on the ``-E'' flag). The swap partition (usually 'b') should have a type of "swap", all other native OpenBSD partitions should have a type of "4.2BSD". Block and fragment sizes are usually 8192 and 1024 bytes, but can also be 16384 and 2048 bytes. The install program will now label your disk and ask which file systems should be created on which partitions. It will auto- matically select the 'a' partition to be the root file system. Next it will ask for which disk and partition you want a file system created on. This will be the same as the disk name (e.g. "sd0") with the letter identifying the partition (e.g. "d") appended (e.g. "sd0d"). Then it will ask where this partition is to be mounted, e.g. /usr. This process will be repeated until you enter "done". At this point you will be asked to confirm that the file system information you have entered is correct, and given an opportunity to change the file system table. Next it will create the new file systems as specified, OVERWRITING ANY EXISTING DATA. This is the point of no return. After all your file systems have been created, the install program will give you an opportunity to configure the network. The network configuration you enter (if any) can then be used to do the install from another system using NFS, HTTP or FTP, and will also be the configuration used by the system after the installation is complete. If you select to configure the network, the install program will ask you for a name of your system and the DNS domain name to use. Note that the host name should be without the domain part, and that the domain name should NOT {:-include-:} the host name part. Next the system will give you a list of network interfaces you can configure. For each network interface you select to configure, it will ask for the IP address to use, the symbolic host name to use, the netmask to use and any interface-specific flags to set. The interface-specific flags are usually used to determine which media the network card is to use. The flags usually carry the following meaning: -link0 -link1 Use BNC (coaxial) port [default] link0 -link1 Use AUI port link0 link1 Use UTP (twisted pair) port After all network interfaces has been configured the install pro- gram will ask for a default route and IP address of the primary name server to use. You will also be presented with an opportunity to edit the host table. At this point you will be allowed to edit the file system table that will be used for the remainder of the installation and that will be used by the finished system, following which the new file systems will be mounted to complete the installation. After these preparatory steps has been completed, you will be able to extract the distribution sets onto your system. There are several install methods supported; FTP, HTTP, tape, CD-ROM, NFS or a local disk partition. To install from a tape, the distrib- ution sets must have been written to tape prior to running the installation program, either as tar images or as gzipped tar images. Note that installation from floppies is not currently supported. OpenBSDFTPInstall OpenBSDHTTPInstall OpenBSDTAPEInstall OpenBSDCDROMInstall OpenBSDNFSInstall OpenBSDDISKInstall({:-"wdN" or -:},{:-only -:}) OpenBSDCommonFS OpenBSDCommonURL OpenBSDCongratulations