dnl $OpenBSD: install,v 1.9 2008/08/05 22:58:01 miod Exp $ OpenBSDInstallPrelude If OpenBSD will be sharing the disk with another operating system, you should have already completed the section of these notes that instructed you on how to prepare your hard disk. You should know the size of the OpenBSD area of the disk and its offset from the beginning of the disk. You will need this information when setting up your OpenBSD partitions. There are several ways to install OpenBSD onto a disk. The easiest way, should your computer support it, is to boot off the OpenBSD CD-ROM, or off the bootable CD-ROM mini image. Otherwise, you can boot from a 3.5" 1.44MB floppy disk if your machine has a floppy drive. If your machine supports PXE network boots, you could try to configure a server for a network install. OpenBSDInstallPart2 If you are using CD-ROM or floppy media, ensure the disk is in the drive before starting. Reboot the computer to begin the install. You might have to play with your BIOS options to get the computer to boot from the correct installation media (floppy, CD, or network/PXE) rather than from the hard disk. If you are installing across the network with PXE, you will need to tell pxeboot to get the bsd.rd install kernel: boot> boot bsd.rd It can take a while to load the kernel from a floppy, slow speed CD-ROM drive, or across a network, most likely more than a minute. If some action doesn't eventually happen, or the spinning cursor has stopped and nothing further has happened, either your boot floppy is bad or you are having hardware problems. If trying another floppy disk doesn't help, try booting after disabling your CPU's internal and external caches (if any). If it still doesn't work, OpenBSD probably can't be run on your hardware. This can probably be considered a bug, so you might want to report it. If you do, please {:-include-:} as many details about your system configuration as you can. OpenBSDBootMsgs You will next be asked for your terminal type. If you are installing from a non-serial console, the default of "vt220" is correct. If you are installing from a serial console you should choose the terminal type from amongst those listed. (If your terminal type is xterm, just use vt220.) OpenBSDInstallPart3 Next you will have to edit or create a disk label for the disk OpenBSD is being installed on. If there are any existing partitions defined (for any operating system), and a disk label is not found, you will first be given an opportunity to run fdisk and create an OpenBSD partition. If fdisk is being invoked on your behalf, it will start by displaying the current partitions defined and then allow you to modify this information, add new partitions, and change which partition to boot from by default. If you make a mistake, you will be allowed to repeat this procedure as necessary to correct this. Note that you should make OpenBSD be the active partition at least until the install has been completed. OpenBSDInstallPart4({:- If you have DOS or Linux partitions defined on the disk, these will usually show up as partition 'h', 'i' and so on.-:}) Note that all OpenBSD partitions in the disk label must have an offset that makes it start within the OpenBSD part of the disk, and a size that keeps it inside of that portion of the disk. This is within the bounds of the 'c' partition if the disk is not being shared with other operating systems, and within the OpenBSD fdisk partition if the disk is being shared. OpenBSDInstallPart5(wd0) OpenBSDInstallNet({:-CD-ROM, -:},nofloppy) OpenBSDFTPInstall OpenBSDHTTPInstall OpenBSDTAPEInstall OpenBSDCDROMInstall OpenBSDDISKInstall({:-"wdN" or -:},,{:- or MS-DOS-:}) OpenBSDCommonFS OpenBSDCommonURL OpenBSDInstallWrapup OpenBSDInstallAperture OpenBSDInstallConsole OpenBSDInstallWrapupPart2 OpenBSDCongratulations