dnl	$OpenBSD: install,v 1.3 2004/03/08 22:31:28 miod Exp $
OpenBSDInstallPrelude

If OpenBSD will be sharing the disk with another operating system,
you should have already completed the section of these notes that
instructed you on how to prepare your hard disk.  You should know
the size of the OpenBSD area of the disk and its offset from the
beginning of the disk.  You will need this information when setting up
your OpenBSD partitions.  If your BIOS uses translated geometry, you
should use this geometry for the remainder of the install.  This is
only necessary if you are sharing the disk with other operating systems
that use the translated geometry.

There are several ways to install OpenBSD onto a disk.  The easiest way,
should your computer support it, is to boot off the OpenBSD CD-ROM, or
off the bootable CD-ROM mini image. Otherwise, you can boot from a 3.5"
1.44MB floppy disk if your machine has a floppy drive.

OpenBSDInstallPart2

	With either the CD-ROM or the floppy in the drive, reboot your
	computer. You might have to play with your BIOS options to let the
	computer boot from the installation media, rather than the hard
	disk.

	It will take a while to load the kernel from a floppy or slow
	speed CD-ROM drive, most likely more than a minute.  If some
	action doesn't eventually happen, or the spinning cursor has
	stopped and nothing further has happened, either your boot floppy
	is bad or you are having hardware problems. If trying another
	floppy disk doesn't help, try booting after disabling your CPU's
	internal and external caches (if any).  If it still doesn't work,
	OpenBSD probably can't be run on your hardware.  This can probably
	be considered a bug, so you might want to report it.
	If you do, please {:-include-:} as many details about your system
	configuration as you can.

OpenBSDBootMsgs

	You will next be asked for your terminal type.  You should just
	hit return to select the default (vt220).

dnl Replace the following paragraph...
	After entering the terminal type you will be asked whether you
        wish to do an "(I)nstall".  Enter 'I' for a fresh install.

	You will be presented with a welcome message and asked if
        you really wish to install.  Assuming you answered yes, the
	install program will then tell you which disks of that type
	it can install on, and ask you which it should use.
	The name of the disk is typically "sd0" for SCSI drives or
	"wd0" for IDE/RLL/ESDI/ST506 drives.
        Reply with the name of your disk.
dnl with this:
dnl OpenBSDInstallPart3({:- or "wd0" for IDE/RLL/ESDI/ST506 drives-:})
dnl once upgrades are available

	Next you will have to edit or create a disk label for the disk
	OpenBSD is being installed on.  If there are any existing
	partitions defined (for any operating system), and a disk label
	is not found, you will first be given an opportunity to run
	fdisk and create an OpenBSD partition.

	If fdisk is being invoked on your behalf, it will start by
	displaying the current partitions defined and then allow you
	to modify this information, add new partitions and change
	which partition to boot from by default.  If you make a mistake,
	you will be allowed to repeat this procedure as necessary to
	correct this.  Note that you should make OpenBSD be the active
	partition at least until the install has been completed.

OpenBSDInstallPart4({:- If you have DOS or Linux partitions
	defined on the disk, these will usually show up as partition
	'h', 'i' and so on.-:})

	Note that all OpenBSD partitions in the disk label must have an
	offset that makes it start within the OpenBSD part of the disk,
	and a size that keeps it inside of that portion of the disk.  This
	is within the bounds of the 'c' partition if the disk is not being
	shared with other operating systems, and within the OpenBSD fdisk
	partition if the disk is being shared.

OpenBSDInstallPart5(wd0)

OpenBSDInstallNet({:-CD-ROM, -:},nofloppy)

OpenBSDFTPInstall

OpenBSDHTTPInstall

OpenBSDTAPEInstall

OpenBSDCDROMInstall

OpenBSDDISKInstall({:-"wdN" or -:},,{:- or MS-DOS-:})

OpenBSDCommonFS

OpenBSDCommonURL

OpenBSDCongratulations