Installation is supported from several media types, including:

	AmigaDOS partitions
	FFS partitions
	Tape
	Remote NFS partition
	FTP
	HTTP

The installation program is run under a minimal OpenBSD environment
provided by one of two means: a ramdisk or a miniroot filesystem.
We recommend using the ramdisk if your machine is big enough (at
least 6MB of fastmem is required), otherwise a miniroot filesystem
needs to be transferred to the OpenBSD swap partition.  This can be
done from AmigaDOS in the case of a new install or upgrade, or from
OpenBSD when doing an upgrade.  See the "Preparing your System for
OpenBSD Installation" section for details.

The steps necessary to prepare the distribution sets for
installation depend on which method of installation you choose.
The various methods are explained below.  However, for all methods
you need to transfer a OpenBSD kernel binary to your AmigaDOS
partition, optionally you must also get the miniroot image there
for later transfer to your swap partition as explained elsewhere.
For ramdisk installs you need to get both the bsd and bsd.rd
kernel images, and for miniroot installs you need bsd and the
miniroot22.fs image.

To prepare for installing via an AmigaDOS partition:

	To install OpenBSD from an AmigaDOS partition, you need to
	get the OpenBSD distribution sets you wish to install
	on your system on to an AmigaDOS partition.  All of the
	set_name.tar.gz pieces can be placed in a single directory
	instead of separate ones for each distribution set.  This
	will also simplify the installation work later on.

	Note where you place the files, you will need this later.
	Also, it might be a good idea to type down the AmigaDOS
	partition structure of the disk you put these files on.  In
	the context of the install program you will only be able to
	identify the partition by starting sector (block) number
	and/or size.  The partition names are *not* available.

	Once you have done this, you can proceed to the next
	step in the installation process, preparing your hard disk.

To prepare for installing via a tape:

	To install OpenBSD from a tape, you need to somehow
	get the OpenBSD filesets you wish to install on
	your system on to the appropriate kind of tape,
	in tar format.

	If you're making the tape on a UN*X system, the easiest
	way to do so is:

		tar cvf <tape_device> <files>

	where "<tape_device>" is the name of the tape device
	that describes the tape drive you're using (possibly
	something like /dev/nrst0, but we make no guarantees 8-).
	If you can't figure it out, ask your system administrator.
	"<files>" are the names of the "set_name.tar.gz" files
	which you want to be placed on the tape.

	Once you have done this, you can proceed to the next
	step in the installation process, preparing your hard disk.

To prepare for installing via NFS:

	Place the OpenBSD software you wish to install into
	a directory on an NFS server, and make that directory
	mountable by the machine which you will be installing
	OpenBSD on.  This will probably require modifying the
	/etc/exports file of the NFS server and resetting
	mountd, acts which will require superuser privileges.
	Note the numeric IP address of the NFS server and of
	the router closest to the the new OpenBSD machine,
	if the NFS server is not on a network which is
	directly attached to the OpenBSD machine.

	Once you have done this, you can proceed to the next
	step in the installation process, preparing your hard disk.

To prepare for installing via FTP/HTTP:

	The preparations for this method of installation
	are easy: all you have to do is make sure that
	there's some FTP- or website from which you can
	retrieve the OpenBSD installation when it's time to
	do the install.  You should know the numeric IP
	address of that site, and the numeric IP address of
	your nearest router if one is necessary

	Once you have done this, you can proceed to the next
	step in the installation process, preparing your hard disk.

If you are upgrading OpenBSD, you also have the option of installing
OpenBSD by putting the new distribution sets somewhere in your existing
file system, and using them from there.  To do that, you must do the
following:

	Place the distribution sets you wish to upgrade somewhere in
	your current file system tree.  At a bare minimum, you must
	upgrade the "base" binary distribution, and so must put the
	"base22.tar.gz" set somewhere in your file system.  If you wish,
	you can do the other sets, as well, but you should NOT upgrade
	the "etc" distribution; the "etc" distribution contains system
	configuration files that you should review and update by hand.

	Once you have done this, you can proceed to the next step in
	the upgrade process, actually upgrading your system.