.\"	$OpenBSD: disklabel.8,v 1.107 2012/01/02 04:38:00 krw Exp $
.\"	$NetBSD: disklabel.8,v 1.9 1995/03/18 14:54:38 cgd Exp $
.\"
.\" Copyright (c) 1987, 1988, 1991, 1993
.\"	The Regents of the University of California.  All rights reserved.
.\"
.\" This code is derived from software contributed to Berkeley by
.\" Symmetric Computer Systems.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\"    notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\"    notice, this list of conditions and the following disclaimer in the
.\"    documentation and/or other materials provided with the distribution.
.\" 3. Neither the name of the University nor the names of its contributors
.\"    may be used to endorse or promote products derived from this software
.\"    without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED.  IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
.\" SUCH DAMAGE.
.\"
.\"	@(#)disklabel.8	8.2 (Berkeley) 4/19/94
.\"
.Dd $Mdocdate: January 2 2012 $
.Dt DISKLABEL 8
.Os
.Sh NAME
.Nm disklabel
.Nd read and write disk pack label
.Sh SYNOPSIS
.Nm disklabel
.Op Fl Acdtv
.Op Fl h | p Ar unit
.Ar disk
.Nm disklabel
.Fl w
.Op Fl Acdnv
.Ar disk Ar disktype
.Op Ar packid
.Nm disklabel
.Fl e
.Op Fl Acdnv
.Ar disk
.Nm disklabel
.Fl E
.Op Fl Acdnv
.Op Fl F Ns | Ns Fl f Ar file
.Ar disk
.Nm disklabel
.Fl R
.Op Fl nv
.Ar disk Ar protofile
.Pp
.Nm disklabel
.Fl B\ \&
.Op Fl nv
.Op Fl b Ar boot1
.Ar disk
.Op Ar disktype
.Nm disklabel
.Fl Bw
.Op Fl nv
.Op Fl b Ar boot1
.Ar disk Ar disktype
.Op Ar packid
.Nm disklabel
.Fl BR
.Op Fl nv
.Op Fl b Ar boot1
.Ar disk Ar protofile
.Op Ar disktype
.Sh DESCRIPTION
The
.Nm
utility can be used to install, examine, or modify the label on a disk drive or
pack.
The disk label contains information about disk characteristics
.Pq size, type, etc.
and the partition layout, stored on the disk itself.
It is used by the operating system to optimize disk I/O and
locate the filesystems resident on the disk.
.Pp
.Nm
supports 15 configurable partitions,
.Sq a
through
.Sq p ,
excluding
.Sq c .
The
.Sq c
partition describes the entire physical disk, is automatically created
by the kernel, and cannot be modified or deleted by
.Nm .
By convention, the
.Sq a
partition of the boot disk is the root partition, and the
.Sq b
partition of the boot disk is the swap partition,
but all other letters can be used in any order for any other
partitions as desired.
.Pp
The options are as follows:
.Bl -tag -width Ds
.It Fl A
Automatically allocate all the disk space in the
.Ox
portion of the disk in the recommended manner.
See
.Sx AUTOMATIC DISK ALLOCATION ,
below.
.It Fl B
Install bootstrap code.
Some architectures instead require bootstrap code installation to be
done using an
.Xr installboot 8
type program, as described in
.Xr boot 8 .
.It Fl b Ar boot1
Specify the primary boot program.
.It Fl c
Clear the system's in-core copy of the label and update it based on
the on-disk label.
.It Fl d
Use the
.Em default
label.
This ignores any existing
.Ox
disk label on the disk.
.It Fl E
Use the built-in command-driven label editor described below.
.It Fl e
Edit an existing disk label using the editor specified in the
.Ev EDITOR
environment variable, or
.Xr vi 1
if none is specified.
.It Fl F Ar file
Write entries to
.Ar file
in
.Xr fstab 5
format for any partitions for which mount point information is known.
The entries will be written using disklabel UIDs.
The
.Fl F
flag is only valid when used in conjunction with the
.Fl E
or
.Fl A
flags.
If
.Ar file
already exists, it will be overwritten.
.It Fl f Ar file
The same as
.Fl F
except that entries will be written using disk device names.
.It Fl h
Print partition sizes in human readable format.
.It Fl n
Make no permanent changes to the disklabel
.Pq useful for debugging purposes .
.It Fl p Ar unit
Print partition sizes in
.Ar unit
instead of sectors.
Valid units are b(ytes), c(ylinders), k(ilobytes), m(egabytes), g(igabytes)
and t(erabytes).
For operations other than displaying a partition the
.Ql %
(percent of total) and
.Ql &
(percent of free) units are also accepted.
.It Fl R
Restore a disk label that was formatted in a prior operation and
saved in an
.Tn ASCII
file.
.It Fl t
Format the label as a
.Xr disktab 5
entry.
.It Fl v
Print additional information during operation
.Pq verbose mode .
.It Fl w
Write a standard label on the designated drive.
.It Ar disk
Specify the
.Ar disk
to operate on.
It can be specified by its full pathname, by an abbreviated disk form,
or by its disklabel UID.
In its abbreviated form, the path to the device, the
.Sq r
denoting
.Qq raw device ,
and the partition letter, can all be omitted.
For example, the first IDE disk can be specified as either
.Pa /dev/rwd0c ,
.Pa /dev/wd0c ,
or
.Ar wd0 .
.It Ar disktype
Specify a
.Ar disktype
entry from the
.Xr disktab 5
database.
.It Ar packid
Specify a pack identification string for the device
.Pq see below .
.It Ar protofile
Used with the restore option
.Pq Fl R
to specify a file to read an ASCII label from.
.El
.Pp
The first form of the command
.Pq read
is used to examine the label on the named disk drive.
It will display all of the parameters associated with the drive
and its partition layout.
The kernel's in-core copy of the label is displayed; if
the disk has no label, or the partition types on the disk are
incorrect, the kernel may have constructed or modified the label.
.Pp
The second form of the command
.Pq write
is used to write a standard label on the designated drive.
The drive parameters and partitions are taken from that file.
If different disks of the same physical type are
to have different partitions, it will be necessary to have separate
disktab entries describing each, or to edit the label after
installation as described below.
The optional argument is a pack
identification string, up to 16 characters long.
The pack ID must be quoted if it contains blanks.
The existing label will be updated via the in-core
copy and any bootstrap code will be unaffected.
.Pp
In the third form of the command
.Pq edit ,
the label is read from the in-core kernel copy
and then supplied to an editor for changes.
If no editor is specified in an
.Ev EDITOR
environment variable,
.Xr vi 1
is used.
When the editor terminates, the formatted label is reread and
used to rewrite the disk label.
Existing bootstrap code is unchanged.
.Pp
The built-in label editor
.Pq fourth form
provides a simple interactive label editor.
Some commands or prompts take an optional unit.
Available units are
.Sq b
for bytes,
.Sq c
for cylinders,
.Sq k
for kilobytes,
.Sq m
for megabytes,
.Sq g
for gigabytes,
and
.Sq t
for terabytes.
If no unit is given, the default is to use sectors
(usually 512 bytes).
Quantities will be rounded to the nearest
cylinder when units are specified for sizes
.Pq or offsets .
Commands may be aborted by entering
.Ql ^D
.Pq Control-D .
Entering
.Ql ^D
at the main
.Ql >
prompt will exit the editor.
At prompts that request a size,
.Ql *
may be entered to indicate the rest of the available space.
The editor commands are as follows:
.Bl -tag -width "p [unit] "
.It Cm \&? \*(Ba h
Display help message with all available commands.
There is also
.Pq simple
context-sensitive help available at most prompts.
.It Cm A
Allocate all the disk space in the recommended manner.
See
.Sx AUTOMATIC DISK ALLOCATION ,
below.
.It Cm a Op Ar part
Add new partition.
This option adds a new partition to the disk label.
If no partition letter is specified
.Pq a\-p ,
the user will be prompted for one.
.It Cm b
Set
.Ox
disk boundaries.
This option tells
.Nm
which parts of the disk it is allowed to modify.
This option is probably only useful for ports with
.Xr fdisk 8
partition tables where the ending sector in the MBR is incorrect.
The user may enter
.Ql *
at the
.Dq Size
prompt to indicate the entire size of the disk
.Pq minus the starting sector .
This is useful for disks where the
fdisk partition table is incapable of storing the real size.
Note: data may become corrupted if boundaries are extended such
that they overlap with other resident operating systems.
.It Cm c Op Ar part
Change the size of an existing partition.
If no partition is specified, the user will be prompted for one.
The new size may be
in terms of the aforementioned units and may also be prefixed with
.Ql +
or
.Ql -
to change the size by a relative amount.
.It Cm D
Sets the disk label to the default values as reported by the kernel.
This simulates the case where there is no disk label.
.It Cm d Op Ar part
Delete an existing partition (or
.Ql *
to delete all partitions).
If no partition is specified, the user will be prompted for one.
.It Cm e
Edit drive parameters.
This option is used to set the following parameters:
disk type, a descriptive label string, sectors/track,
tracks/cylinder, sectors/cylinder, number of cylinders,
total sectors, rpm, and interleave.
.It Xo
.Cm g
.Op Ar d | u
.Xc
Set disk geometry based on what the
.Em disk
or
.Em user
thinks (the
.Em user
geometry is simply what the label said before
.Nm
made any changes).
.It Cm i
Change the disklabel UID, specified as a 16-character hexadecimal string.
If set to all zeros, a new UID will automatically be allocated when the
disklabel is written to disk.
.It Cm l Op Ar unit
Print the disk label header.
.It Cm M
Display this manual page.
The manual page is piped through the pager specified by the
.Ev PAGER
environment variable or 'less' if
.Ev PAGER
is not set.
.It Cm m Op Ar part
Modify parameters for an existing partition.
If no partition is specified, the user will be prompted for one.
This option allows
the user to change the filesystem type, starting offset, partition size,
and mount point for the specified partition.
If expert mode is enabled (see
.Cm X
below), then block fragment size, block size, and cylinders per group
can also be modified.
Note that not all parameters are configurable for non-BSD partitions.
.It Cm n Op Ar part
Name the mount point for an existing partition.
If no partition is specified, the user will be prompted for one.
This option is only valid if
.Nm
was invoked with the
.Fl f
flag.
.It Cm p Op Ar unit
Print the current partition list.
If a
.Em unit
is given, the size and offsets are displayed in terms of the
specified unit.
If the unit is
.Sq *
it is automatically determined by the size of the smallest
partition.
.It Cm q
Quit the editor.
If any changes have been made, the user will be
asked whether or not to save the changes to the on-disk label.
.It Cm R Op Ar part
Resize a partition in an automatically allocated label,
compacting unused space between partitions with a higher offset.
The last partition will be shrunk if necessary.
Works only for automatically allocated labels with no spoofed partitions.
.It Cm r
Recalculate free space.
This command displays all the free areas on the disk and the total
number of free sectors.
.It Cm s Op Ar path
Save the label to a file in
.Tn ASCII
format (suitable for loading via the
.Fl R
option).
If no path is specified, the user will be prompted for one.
.It Cm U
Undo all changes made since entering the editor.
.It Cm u
Undo
.Pq or redo
last change.
Entering
.Em u
once will undo the last change.
Entering it again will restore the change.
.It Cm w
Write the label to disk.
This option will commit any changes to the on-disk label.
.It Cm X
Toggle
.Dq expert mode .
By default, some settings are reserved for experts only
(such as the block and fragment size on ffs partitions).
.It Cm x
Exit the editor without saving any changes to the on-disk label.
.It Cm z
Zero out the existing partition table and mountpoint information,
leaving only the 'c' partition.
The drive parameters are not changed.
.El
.Pp
In the restore form of the command
.Pq fifth form ,
the prototype file used to create the label should be in the same format
as that produced when reading or editing a label.
Comments are delimited by
.Ar #
and newline.
Any existing bootstrap code will be unaffected.
.Pp
The final three forms of
.Nm
are used to install bootstrap code on machines where the bootstrap is
part of the label.
.Pp
When installing bootstrap code with the
.Fl B
flag, if the boot program name is not explicitly given with
.Fl b Ar boot1 ,
a standard boot program
will be used.
The standard boot programs are located in
.Pa /usr/mdec .
The name of the program is taken from the
.Dq b0
parameter of the
.Xr disktab 5
entry for the disk if
.Ar disktype
was given and its disktab entry exists and includes a b0 field.
Otherwise, the boot program name is derived from the name of the
disk.
These names are of the form
.Pa basename Ns boot .
For example,
.Pa /usr/mdec/sdboot
if the disk device is
.Em sd0 .
.Pp
The first of the three boot-installation forms is used to install
bootstrap code without changing the existing label.
It is essentially a read command with respect to the disk label itself
and all options are related to the specification of the boot program
as described previously.
The final two forms are analogous to the basic write and restore versions
except that they will install bootstrap code in addition to a new label.
.Pp
Note that when a disk has no real BSD disklabel, the kernel creates a
default label so that the disk can be used.
This default label will include other partitions found on the disk if
they are supported on your architecture.
For example, on systems that support
.Xr fdisk 8
partitions the default label will also include DOS and Linux partitions.
However, these entries are not dynamic, they are fixed at the time
.Nm
is run.
That means that subsequent changes that affect non-OpenBSD
partitions will not be present in the default label,
though they may be updated by hand.
To see the default label, run
.Nm
with the
.Fl d
flag.
.Nm
can then be run with the
.Fl e
flag and any entries pasted as desired from the default label into the real one.
.Sh AUTOMATIC DISK ALLOCATION
The
.Fl A
option and the editor command
.Cm A
automatically create a disklabel with a set of partitions
suitable for a majority of
.Ox
installations.
Any existing
.Ox
disklabel on the disk is ignored, but native partitions
that would normally be spoofed are preserved in the disklabel,
and are not modified during the allocation process.
.Pp
Disk size determines the set of partitions which are created.
Each partition is allocated space between a specified minimum
and maximum.
Each partition is allocated its minimum and remaining space
is split between the partitions up to their maximum allowed space,
which is a fixed percentage.
Space left after all partitions have reached their maximum size
is left unallocated.
The sizes below are approximations,
and may vary from architecture to architecture.
.Pp
.Sy Disks \*(Gt 7 Gigabytes
.Bd -literal -offset indent -compact
/		 5% of disk.  80M \(en 1G
swap		 5% of disk.  80M \(en 2x max physical memory
/tmp		 8% of disk. 120M \(en 4G
/var		13% of disk.  80M \(en 2x size of crash dump
/usr		 5% of disk. 900M \(en 2G
/usr/X11R6	 3% of disk. 512M \(en 1G
/usr/local	10% of disk.   2G \(en 10G
/usr/src	 2% of disk.   1G \(en 2G
/usr/obj	 4% of disk. 1.3G \(en 2G
/home		45% of disk.   1G \(en 300G
.Ed
.Pp
.Sy Disks \*(Gt 2 Gigabytes
.Bd -literal -offset indent -compact
/		 5% of disk. 800M \(en 2G
swap		10% of disk.  80M \(en 2x max physical memory
/usr		78% of disk. 900M \(en 3G
/home		 7% of disk. 256M \(en 2G
.Ed
.Pp
.Sy Disks \*(Gt 700 Megabytes
.Bd -literal -offset indent -compact
/		95% of disk. 700M \(en 4G
swap		 5% of disk.   1M \(en 2x max physical memory
.Ed
.Sh FILES
.Bl -tag -width Pa -compact
.It Pa /etc/disklabels
Directory for backup labels.
.It Pa /etc/disktab
Disk description file.
.It Pa /usr/mdec/ Ns Em xx Ns boot
Primary bootstrap.
.It Pa /usr/mdec/boot Ns Em xx
Secondary bootstrap.
.El
.Sh EXAMPLES
Display the in-core label for sd0 as obtained via
.Pa /dev/rsd0c :
.Pp
.Dl # disklabel sd0
.Pp
Create a label for sd0 based on information for
.Dq sd2212
found in
.Pa /etc/disktab .
Any existing bootstrap code will be clobbered.
.Pp
.Dl # disklabel -w /dev/rsd0c sd2212 foo
.Pp
Read the on-disk label from a disk with DUID 3eb7f9da875cb9ee,
edit it and reinstall in-core as well as on-disk.
Existing bootstrap code is unaffected.
.Pp
.Dl # disklabel -E 3eb7f9da875cb9ee
.Pp
Restore the on-disk and in-core label for sd0 from information in
.Pa mylabel .
Existing bootstrap code is unaffected.
.Pp
.Dl # disklabel -R sd0 mylabel
.Pp
Install a new bootstrap on sd0.
The boot code comes from
.Pa /usr/mdec/sdboot
and possibly
.Pa /usr/mdec/bootsd .
On-disk and in-core labels are unchanged, but on some systems other
information may be destroyed.
Use with care.
.Pp
.Dl # disklabel -B sd0
.Pp
Install a new label and bootstrap.
The label is derived from disktab information for
.Dq sd2212
and installed both in-core and
on-disk.
The bootstrap code comes from the file
.Pa /usr/mdec/newboot .
.Pp
.Dl # disklabel -w -B /dev/rsd0c -b newboot sd2212
.Sh DIAGNOSTICS
The kernel device drivers will not allow the size of a disk partition
to be decreased or the offset of a partition to be changed while
it is open.
Some device drivers create a label containing only a
single large partition if a disk is unlabeled; thus, the label must
be written to the
.Sq a
partition of the disk while it is open.
This sometimes requires the desired label to be set in two steps,
the first one creating at least one other partition, and the second
setting the label on the new partition while shrinking the
.Sq a
partition.
.Pp
On some machines the bootstrap code may not fit entirely in the
area allocated for it by some filesystems.
As a result, it may
not be possible to have filesystems on some partitions of a
.Dq bootable
disk.
When installing bootstrap code,
.Nm
checks for these cases.
If the installed boot code would overlap a partition of type
.Dv FS_UNUSED
it is marked as type
.Dv FS_BOOT .
The
.Xr newfs 8
utility will disallow creation of filesystems on
.Dv FS_BOOT
partitions.
Conversely, if a partition has a type other than
.Dv FS_UNUSED
or
.Dv FS_BOOT ,
.Nm
will not install bootstrap code that overlaps it.
.Sh SEE ALSO
.Xr disklabel 5 ,
.Xr disktab 5 ,
.Xr scan_ffs 8
.Sh CAVEATS
The maximum disk and partition size is 64PB.
.Pp
On some machines, such as Sparc and Sparc64, partition tables
may not exhibit the full functionality described above.