.\" $OpenBSD: raidctl.8,v 1.19 2001/12/30 00:31:03 brad Exp $ .\" $NetBSD: raidctl.8,v 1.24 2001/07/10 01:30:52 lukem Exp $ .\" .\" Copyright (c) 1998 The NetBSD Foundation, Inc. .\" All rights reserved. .\" .\" This code is derived from software contributed to The NetBSD Foundation .\" by Greg Oster .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" 3. All advertising materials mentioning features or use of this software .\" must display the following acknowledgement: .\" This product includes software developed by the NetBSD .\" Foundation, Inc. and its contributors. .\" 4. Neither the name of The NetBSD Foundation nor the names of its .\" contributors may be used to endorse or promote products derived .\" from this software without specific prior written permission. .\" .\" THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS .\" ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED .\" TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR .\" PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS .\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR .\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF .\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS .\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN .\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) .\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE .\" POSSIBILITY OF SUCH DAMAGE. .\" .\" .\" Copyright (c) 1995 Carnegie-Mellon University. .\" All rights reserved. .\" .\" Author: Mark Holland .\" .\" Permission to use, copy, modify and distribute this software and .\" its documentation is hereby granted, provided that both the copyright .\" notice and this permission notice appear in all copies of the .\" software, derivative works or modified versions, and any portions .\" thereof, and that both notices appear in supporting documentation. .\" .\" CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS "AS IS" .\" CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND .\" FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. .\" .\" Carnegie Mellon requests users of this software to return to .\" .\" Software Distribution Coordinator or Software.Distribution@CS.CMU.EDU .\" School of Computer Science .\" Carnegie Mellon University .\" Pittsburgh PA 15213-3890 .\" .\" any improvements or extensions that they make and grant Carnegie the .\" rights to redistribute these changes. .\" .Dd July 10, 2001 .Dt RAIDCTL 8 .Os .Sh NAME .Nm raidctl .Nd configuration utility for the RAIDframe disk driver .Sh SYNOPSIS .Nm raidctl .Op Fl v .Fl a Ar component Ar dev .Nm raidctl .Op Fl v .Fl A Op yes | no | root .Ar dev .Nm raifctl .Op Fl v .Fl B Ar dev .Nm raidctl .Op Fl v .Fl c Ar config_file Ar dev .Nm raidctl .Op Fl v .Fl C Ar config_file Ar dev .Nm raidctl .Op Fl v .Fl f Ar component Ar dev .Nm raidctl .Op Fl v .Fl F Ar component Ar dev .Nm raidctl .Op Fl v .Fl g Ar component Ar dev .Nm raidctl .Op Fl v .Fl G Ar dev .Nm raidctl .Op Fl v .Fl i Ar dev .Nm raidctl .Op Fl v .Fl I Ar serial_number Ar dev .Nm raidctl .Op Fl v .Fl p Ar dev .Nm raidctl .Op Fl v .Fl P Ar dev .Nm raidctl .Op Fl v .Fl r Ar component Ar dev .Nm raidctl .Op Fl v .Fl R Ar component Ar dev .Nm raidctl .Op Fl v .Fl s Ar dev .Nm raidctl .Op Fl v .Fl S Ar dev .Nm raidctl .Op Fl v .Fl u Ar dev .Sh DESCRIPTION .Nm is the user-land control program for .Xr raid 4 , the RAIDframe disk device. .Nm is primarily used to dynamically configure and unconfigure RAIDframe disk devices. For more information about the RAIDframe disk device, see .Xr raid 4 . .Pp This document assumes the reader has at least rudimentary knowledge of RAID and RAID concepts. .Pp The command-line options for .Nm are as follows: .Bl -tag -width indent .It Fl a Ar component Ar dev Add .Ar component as a hot spare for the device .Ar dev . .It Fl A Ic yes Ar dev Make the RAID set auto-configurable. The RAID set will be automatically configured at boot .Ar before the root file system is mounted. Note that all components of the set must be of type RAID in the disklabel. .It Fl A Ic no Ar dev Turn off auto-configuration for the RAID set. .It Fl A Ic root Ar dev Make the RAID set auto-configurable, and also mark the set as being eligible to be the root partition. A RAID set configured this way will .Ar override the use of the boot disk as the root device. All components of the set must be of type RAID in the disklabel. Note that the kernel being booted must currently reside on a non-RAID set. .It Fl B Ar dev Initiate a copyback of reconstructed data from a spare disk to its original disk. This is performed after a component has failed, and the failed drive has been reconstructed onto a spare drive. .It Fl c Ar config_file Ar dev Configure the RAIDframe device .Ar dev according to the configuration given in .Ar config_file . A description of the contents of .Ar config_file is given later. .It Fl C Ar config_file Ar dev As for .Ar -c , but forces the configuration to take place. This is required the first time a RAID set is configured. .It Fl f Ar component Ar dev This marks the specified .Ar component as having failed, but does not initiate a reconstruction of that component. .It Fl F Ar component Ar dev Fails the specified .Ar component of the device, and immediately begin a reconstruction of the failed disk onto an available hot spare. This is one of the mechanisms used to start the reconstruction process if a component does have a hardware failure. .It Fl g Ar component Ar dev Get the component label for the specified component. .It Fl G Ar dev Generate the configuration of the RAIDframe device in a format suitable for use with .Nm .Fl c or .Fl C . .It Fl i Ar dev Initialize the RAID device. In particular, (re-write) the parity on the selected device. This .Ar MUST be done for .Ar all RAID sets before the RAID device is labeled and before file systems are created on the RAID device. .It Fl I Ar serial_number Ar dev Initialize the component labels on each component of the device. .Ar serial_number is used as one of the keys in determining whether a particular set of components belong to the same RAID set. While not strictly enforced, different serial numbers should be used for different RAID sets. This step .Ar MUST be performed when a new RAID set is created. .It Fl p Ar dev Check the status of the parity on the RAID set. Displays a status message, and returns successfully if the parity is up-to-date. .It Fl P Ar dev Check the status of the parity on the RAID set, and initialize (re-write) the parity if the parity is not known to be up-to-date. This is normally used after a system crash (and before a .Xr fsck 8 ) to ensure the integrity of the parity. .It Fl r Ar component Ar dev Remove the spare disk specified by .Ar component from the set of available spare components. .It Fl R Ar component Ar dev Fails the specified .Ar component , if necessary, and immediately begins a reconstruction back to .Ar component . This is useful for reconstructing back onto a component after it has been replaced following a failure. .It Fl s Ar dev Display the status of the RAIDframe device for each of the components and spares. .It Fl S Ar dev Check the status of parity re-writing, component reconstruction, and component copyback. The output indicates the amount of progress achieved in each of these areas. .It Fl u Ar dev Unconfigure the RAIDframe device. .It Fl v Be more verbose. For operations such as reconstructions, parity re-writing, and copybacks, provide a progress indicator. .El .Pp The device used by .Nm is specified by .Ar dev . .Ar dev may be either the full name of the device, e.g. /dev/rraid0c, or just simply raid0 (for /dev/rraid0c). .Pp .Ss Configuration file The format of the configuration file is complex, and only an abbreviated treatment is given here. In the configuration files, a .Sq # indicates the beginning of a comment. .Pp There are 4 required sections of a configuration file, and 2 optional sections. Each section begins with a .Sq START , followed by the section name, and the configuration parameters associated with that section. The first section is the .Sq array section, and it specifies the number of rows, columns, and spare disks in the RAID set. For example: .Bd -unfilled -offset indent START array 1 3 0 .Ed .Pp indicates an array with 1 row, 3 columns, and 0 spare disks. Note that although multi-dimensional arrays may be specified, they are .Ar NOT supported in the driver. .Pp The second section, the .Sq disks section, specifies the actual components of the device. For example: .Bd -unfilled -offset indent START disks /dev/sd0e /dev/sd1e /dev/sd2e .Ed .Pp specifies the three component disks to be used in the RAID device. If any of the specified drives cannot be found when the RAID device is configured, then they will be marked as .Sq failed , and the system will operate in degraded mode. Note that it is .Ar imperative that the order of the components in the configuration file does not change between configurations of a RAID device. Changing the order of the components will result in data loss if the set is configured with the .Fl C option. In normal circumstances, the RAID set will not configure if only .Fl c is specified, and the components are out-of-order. .Pp The next section, which is the .Sq spare section, is optional, and, if present, specifies the devices to be used as .Sq hot spares -- devices which are on-line, but are not actively used by the RAID driver unless one of the main components fail. A simple .Sq spare section might be: .Bd -unfilled -offset indent START spare /dev/sd3e .Ed .Pp for a configuration with a single spare component. If no spare drives are to be used in the configuration, then the .Sq spare section may be omitted. .Pp The next section is the .Sq layout section. This section describes the general layout parameters for the RAID device, and provides such information as sectors per stripe unit, stripe units per parity unit, stripe units per reconstruction unit, and the parity configuration to use. This section might look like: .Bd -unfilled -offset indent START layout # sectPerSU SUsPerParityUnit SUsPerReconUnit RAID_level 32 1 1 5 .Ed .Pp The sectors per stripe unit specifies, in blocks, the interleave factor; i.e. the number of contiguous sectors to be written to each component for a single stripe. Appropriate selection of this value (32 in this example) is the subject of much research in RAID architectures. The stripe units per parity unit and stripe units per reconstruction unit are normally each set to 1. While certain values above 1 are permitted, a discussion of valid values and the consequences of using anything other than 1 are outside the scope of this document. The last value in this section (5 in this example) indicates the parity configuration desired. Valid entries include: .Bl -tag -width inde .It 0 RAID level 0. No parity, only simple striping. .It 1 RAID level 1. Mirroring. The parity is the mirror. .It 4 RAID level 4. Striping across components, with parity stored on the last component. .It 5 RAID level 5. Striping across components, parity distributed across all components. .El .Pp There are other valid entries here, including those for Even-Odd parity, RAID level 5 with rotated sparing, Chained declustering, and Interleaved declustering, but as of this writing the code for those parity operations has not been tested with .Nx . .Pp The next required section is the .Sq queue section. This is most often specified as: .Bd -unfilled -offset indent START queue fifo 100 .Ed .Pp where the queuing method is specified as fifo (first-in, first-out), and the size of the per-component queue is limited to 100 requests. Other queuing methods may also be specified, but a discussion of them is beyond the scope of this document. .Pp The final section, the .Sq debug section, is optional. For more details on this the reader is referred to the RAIDframe documentation discussed in the .Sx HISTORY section. See .Sx EXAMPLES for a more complete configuration file example. .Sh EXAMPLES It is highly recommended that before using the RAID driver for real file systems that the system administrator(s) become quite familiar with the use of .Nm "" , and that they understand how the component reconstruction process works. The examples in this section will focus on configuring a number of different RAID sets of varying degrees of redundancy. By working through these examples, administrators should be able to develop a good feel for how to configure a RAID set, and how to initiate reconstruction of failed components. .Pp In the following examples .Sq raid0 will be used to denote the RAID device. .Sq /dev/rraid0c may be used in place of .Sq raid0 . .Pp .Ss Initialization and Configuration The initial step in configuring a RAID set is to identify the components that will be used in the RAID set. All components should be the same size. Each component should have a disklabel type of .Dv FS_RAID , and a typical disklabel entry for a RAID component might look like: .Bd -unfilled -offset indent f: 1800000 200495 RAID # (Cyl. 405*- 4041*) .Ed .Pp While .Dv FS_BSDFFS will also work as the component type, the type .Dv FS_RAID is preferred for RAIDframe use, as it is required for features such as auto-configuration. As part of the initial configuration of each RAID set, each component will be given a .Sq component label . A .Sq component label contains important information about the component, including a user-specified serial number, the row and column of that component in the RAID set, the redundancy level of the RAID set, a 'modification counter', and whether the parity information (if any) on that component is known to be correct. Component labels are an integral part of the RAID set, since they are used to ensure that components are configured in the correct order, and used to keep track of other vital information about the RAID set. Component labels are also required for the auto-detection and auto-configuration of RAID sets at boot time. For a component label to be considered valid, that particular component label must be in agreement with the other component labels in the set. For example, the serial number, .Sq modification counter , number of rows and number of columns must all be in agreement. If any of these are different, then the component is not considered to be part of the set. See .Xr raid 4 for more information about component labels. .Pp Once the components have been identified, and the disks have appropriate labels, .Nm "" is then used to configure the .Xr raid 4 device. To configure the device, a configuration file which looks something like: .Bd -unfilled -offset indent START array # numRow numCol numSpare 1 3 1 START disks /dev/sd1e /dev/sd2e /dev/sd3e START spare /dev/sd4e START layout # sectPerSU SUsPerParityUnit SUsPerReconUnit RAID_level_5 32 1 1 5 START queue fifo 100 .Ed .Pp is created in a file. The above configuration file specifies a RAID 5 set consisting of the components /dev/sd1e, /dev/sd2e, and /dev/sd3e, with /dev/sd4e available as a .Sq hot spare in case one of the three main drives should fail. A RAID 0 set would be specified in a similar way: .Bd -unfilled -offset indent START array # numRow numCol numSpare 1 4 0 START disks /dev/sd10e /dev/sd11e /dev/sd12e /dev/sd13e START layout # sectPerSU SUsPerParityUnit SUsPerReconUnit RAID_level_0 64 1 1 0 START queue fifo 100 .Ed .Pp In this case, devices /dev/sd10e, /dev/sd11e, /dev/sd12e, and /dev/sd13e are the components that make up this RAID set. Note that there are no hot spares for a RAID 0 set, since there is no way to recover data if any of the components fail. .Pp For a RAID 1 (mirror) set, the following configuration might be used: .Bd -unfilled -offset indent START array # numRow numCol numSpare 1 2 0 START disks /dev/sd20e /dev/sd21e START layout # sectPerSU SUsPerParityUnit SUsPerReconUnit RAID_level_1 128 1 1 1 START queue fifo 100 .Ed .Pp In this case, /dev/sd20e and /dev/sd21e are the two components of the mirror set. While no hot spares have been specified in this configuration, they easily could be, just as they were specified in the RAID 5 case above. Note as well that RAID 1 sets are currently limited to only 2 components. At present, n-way mirroring is not possible. .Pp The first time a RAID set is configured, the .Fl C option must be used: .Bd -unfilled -offset indent raidctl -C raid0.conf raid0 .Ed .Pp where .Sq raid0.conf is the name of the RAID configuration file. The .Fl C forces the configuration to succeed, even if any of the component labels are incorrect. The .Fl C option should not be used lightly in situations other than initial configurations, as if the system is refusing to configure a RAID set, there is probably a very good reason for it. After the initial configuration is done (and appropriate component labels are added with the .Fl I option) then raid0 can be configured normally with: .Bd -unfilled -offset indent raidctl -c raid0.conf raid0 .Ed .Pp When the RAID set is configured for the first time, it is necessary to initialize the component labels, and to initialize the parity on the RAID set. Initializing the component labels is done with: .Bd -unfilled -offset indent raidctl -I 112341 raid0 .Ed .Pp where .Sq 112341 is a user-specified serial number for the RAID set. This initialization step is .Ar required for all RAID sets. As well, using different serial numbers between RAID sets is .Ar strongly encouraged , as using the same serial number for all RAID sets will only serve to decrease the usefulness of the component label checking. .Pp Initializing the RAID set is done via the .Fl i option. This initialization .Ar MUST be done for .Ar all RAID sets, since among other things it verifies that the parity (if any) on the RAID set is correct. Since this initialization may be quite time-consuming, the .Fl v option may be also used in conjunction with .Fl i : .Bd -unfilled -offset indent raidctl -iv raid0 .Ed .Pp This will give more verbose output on the status of the initialization: .Bd -unfilled -offset indent Initiating re-write of parity Parity Re-write status: 10% |**** | ETA: 06:03 / .Ed .Pp The output provides a .Sq Percent Complete in both a numeric and graphical format, as well as an estimated time to completion of the operation. .Pp Since it is the parity that provides the .Sq redundancy part of RAID, it is critical that the parity is correct as much as possible. If the parity is not correct, then there is no guarantee that data will not be lost if a component fails. .Pp Once the parity is known to be correct, it is then safe to perform .Xr disklabel 8 , .Xr newfs 8 , or .Xr fsck 8 on the device or its filesystems, and then to mount the filesystems for use. .Pp Under certain circumstances (e.g. the additional component has not arrived, or data is being migrated off of a disk destined to become a component) it may be desirable to to configure a RAID 1 set with only a single component. This can be achieved by configuring the set with a physically existing component (as either the first or second component) and with a .Sq fake component. In the following: .Bd -unfilled -offset indent START array # numRow numCol numSpare 1 2 0 START disks /dev/sd6e /dev/sd0e START layout # sectPerSU SUsPerParityUnit SUsPerReconUnit RAID_level_1 128 1 1 1 START queue fifo 100 .Ed .Pp /dev/sd0e is the real component, and will be the second disk of a RAID 1 set. The component /dev/sd6e, which must exist, but have no physical device associated with it, is simply used as a placeholder. Configuration (using .Fl C and .Fl I Ar 12345 as above) proceeds normally, but initialization of the RAID set will have to wait until all physical components are present. After configuration, this set can be used normally, but will be operating in degraded mode. Once a second physical component is obtained, it can be hot-added, the existing data mirrored, and normal operation resumed. .Pp .Ss Maintenance of the RAID set After the parity has been initialized for the first time, the command: .Bd -unfilled -offset indent raidctl -p raid0 .Ed .Pp can be used to check the current status of the parity. To check the parity and rebuild it necessary (for example, after an unclean shutdown) the command: .Bd -unfilled -offset indent raidctl -P raid0 .Ed .Pp is used. Note that re-writing the parity can be done while other operations on the RAID set are taking place (e.g. while doing a .Xr fsck 8 on a file system on the RAID set). However: for maximum effectiveness of the RAID set, the parity should be known to be correct before any data on the set is modified. .Pp To see how the RAID set is doing, the following command can be used to show the RAID set's status: .Bd -unfilled -offset indent raidctl -s raid0 .Ed .Pp The output will look something like: .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: optimal /dev/sd3e: optimal Spares: /dev/sd4e: spare Component label for /dev/sd1e: Row: 0 Column: 0 Num Rows: 1 Num Columns: 3 Version: 2 Serial Number: 13432 Mod Counter: 65 Clean: No Status: 0 sectPerSU: 32 SUsPerPU: 1 SUsPerRU: 1 RAID Level: 5 blocksize: 512 numBlocks: 1799936 Autoconfig: No Last configured as: raid0 Component label for /dev/sd2e: Row: 0 Column: 1 Num Rows: 1 Num Columns: 3 Version: 2 Serial Number: 13432 Mod Counter: 65 Clean: No Status: 0 sectPerSU: 32 SUsPerPU: 1 SUsPerRU: 1 RAID Level: 5 blocksize: 512 numBlocks: 1799936 Autoconfig: No Last configured as: raid0 Component label for /dev/sd3e: Row: 0 Column: 2 Num Rows: 1 Num Columns: 3 Version: 2 Serial Number: 13432 Mod Counter: 65 Clean: No Status: 0 sectPerSU: 32 SUsPerPU: 1 SUsPerRU: 1 RAID Level: 5 blocksize: 512 numBlocks: 1799936 Autoconfig: No Last configured as: raid0 Parity status: clean Reconstruction is 100% complete. Parity Re-write is 100% complete. Copyback is 100% complete. .Ed .Pp This indicates that all is well with the RAID set. Of importance here are the component lines which read .Sq optimal , and the .Sq Parity status line which indicates that the parity is up-to-date. Note that if there are file systems open on the RAID set, the individual components will not be .Sq clean but the set as a whole can still be clean. .Pp To check the component label of /dev/sd1e, the following is used: .Bd -unfilled -offset indent raidctl -g /dev/sd1e raid0 .Ed .Pp The output of this command will look something like: .Bd -unfilled -offset indent Component label for /dev/sd1e: Row: 0 Column: 0 Num Rows: 1 Num Columns: 3 Version: 2 Serial Number: 13432 Mod Counter: 65 Clean: No Status: 0 sectPerSU: 32 SUsPerPU: 1 SUsPerRU: 1 RAID Level: 5 blocksize: 512 numBlocks: 1799936 Autoconfig: No Last configured as: raid0 .Ed .Pp .Ss Dealing with Component Failures If for some reason (perhaps to test reconstruction) it is necessary to pretend a drive has failed, the following will perform that function: .Bd -unfilled -offset indent raidctl -f /dev/sd2e raid0 .Ed .Pp The system will then be performing all operations in degraded mode, where missing data is re-computed from existing data and the parity. In this case, obtaining the status of raid0 will return (in part): .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: failed /dev/sd3e: optimal Spares: /dev/sd4e: spare .Ed .Pp Note that with the use of .Fl f a reconstruction has not been started. To both fail the disk and start a reconstruction, the .Fl F option must be used: .Bd -unfilled -offset indent raidctl -F /dev/sd2e raid0 .Ed .Pp The .Fl f option may be used first, and then the .Fl F option used later, on the same disk, if desired. Immediately after the reconstruction is started, the status will report: .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: reconstructing /dev/sd3e: optimal Spares: /dev/sd4e: used_spare [...] Parity status: clean Reconstruction is 10% complete. Parity Re-write is 100% complete. Copyback is 100% complete. .Ed .Pp This indicates that a reconstruction is in progress. To find out how the reconstruction is progressing the .Fl S option may be used. This will indicate the progress in terms of the percentage of the reconstruction that is completed. When the reconstruction is finished the .Fl s option will show: .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: spared /dev/sd3e: optimal Spares: /dev/sd4e: used_spare [...] Parity status: clean Reconstruction is 100% complete. Parity Re-write is 100% complete. Copyback is 100% complete. .Ed .Pp At this point there are at least two options. First, if /dev/sd2e is known to be good (i.e. the failure was either caused by .Fl f or .Fl F , or the failed disk was replaced), then a copyback of the data can be initiated with the .Fl B option. In this example, this would copy the entire contents of /dev/sd4e to /dev/sd2e. Once the copyback procedure is complete, the status of the device would be (in part): .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: optimal /dev/sd3e: optimal Spares: /dev/sd4e: spare .Ed .Pp and the system is back to normal operation. .Pp The second option after the reconstruction is to simply use /dev/sd4e in place of /dev/sd2e in the configuration file. For example, the configuration file (in part) might now look like: .Bd -unfilled -offset indent START array 1 3 0 START drives /dev/sd1e /dev/sd4e /dev/sd3e .Ed .Pp This can be done as /dev/sd4e is completely interchangeable with /dev/sd2e at this point. Note that extreme care must be taken when changing the order of the drives in a configuration. This is one of the few instances where the devices and/or their orderings can be changed without loss of data! In general, the ordering of components in a configuration file should .Ar never be changed. .Pp If a component fails and there are no hot spares available on-line, the status of the RAID set might (in part) look like: .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: failed /dev/sd3e: optimal No spares. .Ed .Pp In this case there are a number of options. The first option is to add a hot spare using: .Bd -unfilled -offset indent raidctl -a /dev/sd4e raid0 .Ed .Pp After the hot add, the status would then be: .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: failed /dev/sd3e: optimal Spares: /dev/sd4e: spare .Ed .Pp Reconstruction could then take place using .Fl F as describe above. .Pp A second option is to rebuild directly onto /dev/sd2e. Once the disk containing /dev/sd2e has been replaced, one can simply use: .Bd -unfilled -offset indent raidctl -R /dev/sd2e raid0 .Ed .Pp to rebuild the /dev/sd2e component. As the rebuilding is in progress, the status will be: .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: reconstructing /dev/sd3e: optimal No spares. .Ed .Pp and when completed, will be: .Bd -unfilled -offset indent Components: /dev/sd1e: optimal /dev/sd2e: optimal /dev/sd3e: optimal No spares. .Ed .Pp In circumstances where a particular component is completely unavailable after a reboot, a special component name will be used to indicate the missing component. For example: .Bd -unfilled -offset indent Components: /dev/sd2e: optimal component1: failed No spares. .Ed .Pp indicates that the second component of this RAID set was not detected at all by the auto-configuration code. The name .Sq component1 can be used anywhere a normal component name would be used. For example, to add a hot spare to the above set, and rebuild to that hot spare, the following could be done: .Bd -unfilled -offset indent raidctl -a /dev/sd3e raid0 raidctl -F component1 raid0 .Ed .Pp at which point the data missing from .Sq component1 would be reconstructed onto /dev/sd3e. .Pp .Ss RAID on RAID RAID sets can be layered to create more complex and much larger RAID sets. A RAID 0 set, for example, could be constructed from four RAID 5 sets. The following configuration file shows such a setup: .Bd -unfilled -offset indent START array # numRow numCol numSpare 1 4 0 START disks /dev/raid1e /dev/raid2e /dev/raid3e /dev/raid4e START layout # sectPerSU SUsPerParityUnit SUsPerReconUnit RAID_level_0 128 1 1 0 START queue fifo 100 .Ed .Pp A similar configuration file might be used for a RAID 0 set constructed from components on RAID 1 sets. In such a configuration, the mirroring provides a high degree of redundancy, while the striping provides additional speed benefits. .Pp .Ss Auto-configuration and Root on RAID RAID sets can also be auto-configured at boot. To make a set auto-configurable, simply prepare the RAID set as above, and then do a: .Bd -unfilled -offset indent raidctl -A yes raid0 .Ed .Pp to turn on auto-configuration for that set. To turn off auto-configuration, use: .Bd -unfilled -offset indent raidctl -A no raid0 .Ed .Pp RAID sets which are auto-configurable will be configured before the root file system is mounted. These RAID sets are thus available for use as a root file system, or for any other file system. A primary advantage of using the auto-configuration is that RAID components become more independent of the disks they reside on. For example, SCSI ID's can change, but auto-configured sets will always be configured correctly, even if the SCSI ID's of the component disks have become scrambled. .Pp Having a system's root file system .Pq Pa / on a RAID set is also allowed, with the .Sq a partition of such a RAID set being used for .Pa / . To use raid0a as the root file system, simply use: .Bd -unfilled -offset indent raidctl -A root raid0 .Ed .Pp To return raid0a to be just an auto-configuring set simply use the .Fl A Ar yes arguments. .Pp Note that kernels can only be directly read from RAID 1 components on alpha and pmax architectures. On those architectures, the .Dv FS_RAID file system is recognized by the bootblocks, and will properly load the kernel directly from a RAID 1 component. For other architectures, or to support the root file system on other RAID sets, some other mechanism must be used to get a kernel booting. For example, a small partition containing only the secondary boot-blocks and an alternate kernel (or two) could be used. Once a kernel is booting however, and an auto-configuring RAID set is found that is eligible to be root, then that RAID set will be auto-configured and used as the root device. If two or more RAID sets claim to be root devices, then the user will be prompted to select the root device. At this time, RAID 0, 1, 4, and 5 sets are all supported as root devices. .Pp A typical RAID 1 setup with root on RAID might be as follows: .Bl -enum .It wd0a - a small partition, which contains a complete, bootable, basic .Ox installation. .It wd1a - also contains a complete, bootable, basic .Ox installation. .It wd0e and wd1e - a RAID 1 set, raid0, used for the root file system. .It wd0f and wd1f - a RAID 1 set, raid1, which will be used only for swap space. .It wd0g and wd1g - a RAID 1 set, raid2, used for .Pa /usr , .Pa /home , or other data, if desired. .It wd0h and wd0h - a RAID 1 set, raid3, if desired. .El .Pp RAID sets raid0, raid1, and raid2 are all marked as auto-configurable. raid0 is marked as being a root file system. When new kernels are installed, the kernel is not only copied to .Pa / , but also to wd0a and wd1a. The kernel on wd0a is required, since that is the kernel the system boots from. The kernel on wd1a is also required, since that will be the kernel used should wd0 fail. The important point here is to have redundant copies of the kernel available, in the event that one of the drives fail. .Pp There is no requirement that the root file system be on the same disk as the kernel. For example, obtaining the kernel from wd0a, and using sd0e and sd1e for raid0, and the root file system, is fine. It .Ar is critical, however, that there be multiple kernels available, in the event of media failure. .Pp Multi-layered RAID devices (such as a RAID 0 set made up of RAID 1 sets) are .Ar not supported as root devices or auto-configurable devices at this point. (Multi-layered RAID devices .Ar are supported in general, however, as mentioned earlier.) Note that in order to enable component auto-detection and auto-configuration of RAID devices, the line: .Bd -unfilled -offset indent options RAID_AUTOCONFIG .Ed .Pp must be in the kernel configuration file. See .Xr raid 4 for more details. .Pp .Ss Unconfiguration The final operation performed by .Nm is to unconfigure a .Xr raid 4 device. This is accomplished via a simple: .Bd -unfilled -offset indent raidctl -u raid0 .Ed .Pp at which point the device is ready to be reconfigured. .Pp .Ss Performance Tuning Selection of the various parameter values which result in the best performance can be quite tricky, and often requires a bit of trial-and-error to get those values most appropriate for a given system. A whole range of factors come into play, including: .Bl -enum .It Types of components (e.g. SCSI vs. IDE) and their bandwidth .It Types of controller cards and their bandwidth .It Distribution of components among controllers .It IO bandwidth .It file system access patterns .It CPU speed .El .Pp As with most performance tuning, benchmarking under real-life loads may be the only way to measure expected performance. Understanding some of the underlying technology is also useful in tuning. The goal of this section is to provide pointers to those parameters which may make significant differences in performance. .Pp For a RAID 1 set, a SectPerSU value of 64 or 128 is typically sufficient. Since data in a RAID 1 set is arranged in a linear fashion on each component, selecting an appropriate stripe size is somewhat less critical than it is for a RAID 5 set. However: a stripe size that is too small will cause large IO's to be broken up into a number of smaller ones, hurting performance. At the same time, a large stripe size may cause problems with concurrent accesses to stripes, which may also affect performance. Thus values in the range of 32 to 128 are often the most effective. .Pp Tuning RAID 5 sets is trickier. In the best case, IO is presented to the RAID set one stripe at a time. Since the entire stripe is available at the beginning of the IO, the parity of that stripe can be calculated before the stripe is written, and then the stripe data and parity can be written in parallel. When the amount of data being written is less than a full stripe worth, the .Sq small write problem occurs. Since a .Sq small write means only a portion of the stripe on the components is going to change, the data (and parity) on the components must be updated slightly differently. First, the .Sq old parity and .Sq old data must be read from the components. Then the new parity is constructed, using the new data to be written, and the old data and old parity. Finally, the new data and new parity are written. All this extra data shuffling results in a serious loss of performance, and is typically 2 to 4 times slower than a full stripe write (or read). To combat this problem in the real world, it may be useful to ensure that stripe sizes are small enough that a .Sq large IO from the system will use exactly one large stripe write. As is seen later, there are some file system dependencies which may come into play here as well. .Pp Since the size of a .Sq large IO is often (currently) only 32K or 64K, on a 5-drive RAID 5 set it may be desirable to select a SectPerSU value of 16 blocks (8K) or 32 blocks (16K). Since there are 4 data sectors per stripe, the maximum data per stripe is 64 blocks (32K) or 128 blocks (64K). Again, empirical measurement will provide the best indicators of which values will yeild better performance. .Pp The parameters used for the file system are also critical to good performance. For .Xr newfs 8 , for example, increasing the block size to 32K or 64K may improve performance dramatically. As well, changing the cylinders-per-group parameter from 16 to 32 or higher is often not only necessary for larger file systems, but may also have positive performance implications. .Pp .Ss Summary Despite the length of this man-page, configuring a RAID set is a relatively straight-forward process. All that needs to be done is the following steps: .Bl -enum .It Use .Xr disklabel 8 to create the components (of type RAID). .It Construct a RAID configuration file: e.g. .Sq raid0.conf .It Configure the RAID set with: .Bd -unfilled -offset indent raidctl -C raid0.conf raid0 .Ed .Pp .It Initialize the component labels with: .Bd -unfilled -offset indent raidctl -I 123456 raid0 .Ed .Pp .It Initialize other important parts of the set with: .Bd -unfilled -offset indent raidctl -i raid0 .Ed .Pp .It Get the default label for the RAID set: .Bd -unfilled -offset indent disklabel raid0 > /tmp/label .Ed .Pp .It Edit the label: .Bd -unfilled -offset indent vi /tmp/label .Ed .Pp .It Put the new label on the RAID set: .Bd -unfilled -offset indent disklabel -R -r raid0 /tmp/label .Ed .Pp .It Create the file system: .Bd -unfilled -offset indent newfs /dev/rraid0e .Ed .Pp .It Mount the file system: .Bd -unfilled -offset indent mount /dev/raid0e /mnt .Ed .Pp .It Use: .Bd -unfilled -offset indent raidctl -c raid0.conf raid0 .Ed .Pp To re-configure the RAID set the next time it is needed, or put raid0.conf into /etc where it will automatically be started by the /etc/rc scripts. .El .Pp .Sh WARNINGS Certain RAID levels (1, 4, 5, 6, and others) can protect against some data loss due to component failure. However the loss of two components of a RAID 4 or 5 system, or the loss of a single component of a RAID 0 system will result in the entire filesystem being lost. RAID is .Ar NOT a substitute for good backup practices. .Pp Recomputation of parity .Ar MUST be performed whenever there is a chance that it may have been compromised. This includes after system crashes, or before a RAID device has been used for the first time. Failure to keep parity correct will be catastrophic should a component ever fail -- it is better to use RAID 0 and get the additional space and speed, than it is to use parity, but not keep the parity correct. At least with RAID 0 there is no perception of increased data security. .Pp .Sh FILES .Bl -tag -width /dev/XXrXraidX -compact .It Pa /dev/{,r}raid* .Cm raid device special files. .El .Pp .Sh SEE ALSO .Xr raid 4 , .Xr ccd 4 , .Xr rc 8 .Sh BUGS Hot-spare removal is currently not available. .Sh HISTORY RAIDframe is a framework for rapid prototyping of RAID structures developed by the folks at the Parallel Data Laboratory at Carnegie Mellon University (CMU). A more complete description of the internals and functionality of RAIDframe is found in the paper "RAIDframe: A Rapid Prototyping Tool for RAID Systems", by William V. Courtright II, Garth Gibson, Mark Holland, LeAnn Neal Reilly, and Jim Zelenka, and published by the Parallel Data Laboratory of Carnegie Mellon University. .Pp The .Nm command first appeared as a program in CMU's RAIDframe v1.1 distribution. This version of .Nm is a complete re-write, and first appeared in .Nx 1.4 . .Sh COPYRIGHT .Bd -unfilled The RAIDframe Copyright is as follows: Copyright (c) 1994-1996 Carnegie-Mellon University. All rights reserved. Permission to use, copy, modify and distribute this software and its documentation is hereby granted, provided that both the copyright notice and this permission notice appear in all copies of the software, derivative works or modified versions, and any portions thereof, and that both notices appear in supporting documentation. CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS "AS IS" CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. Carnegie Mellon requests users of this software to return to Software Distribution Coordinator or Software.Distribution@CS.CMU.EDU School of Computer Science Carnegie Mellon University Pittsburgh PA 15213-3890 any improvements or extensions that they make and grant Carnegie the rights to redistribute these changes. .Ed