/* $OpenBSD: dcareg.h,v 1.5 2001/09/23 22:01:38 millert Exp $ */ /* $NetBSD: dcareg.h,v 1.6 1996/02/24 00:55:02 thorpej Exp $ */ /* * Copyright (c) 1982, 1986, 1990, 1993 * The Regents of the University of California. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by the University of * California, Berkeley and its contributors. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * @(#)dcareg.h 8.1 (Berkeley) 6/10/93 */ #include /* XXX */ #ifdef hp700 struct dcadevice { vu_char dca_reset; vu_char dca_pad[0x800-1]; vu_char dca_data; /* receive buf or xmit hold */ vu_char dca_ier; /* interrupt enable */ vu_char dca_iir; /* (RO) interrupt identify */ #define dca_fifo dca_iir /* (WO) FIFO control */ vu_char dca_cfcr; /* line control */ vu_char dca_mcr; /* modem control */ vu_char dca_lsr; /* line status */ vu_char dca_msr; /* modem status */ vu_char dca_scr; /* scratch pad */ }; #else struct dcadevice { /* card registers */ u_char dca_pad0; vu_char dca_id; /* 0x01 (read) */ #define dca_reset dca_id /* 0x01 (write) */ u_char dca_pad1; vu_char dca_ic; /* 0x03 */ u_char dca_pad2; vu_char dca_ocbrc; /* 0x05 */ u_char dca_pad3; vu_char dca_lcsm; /* 0x07 */ u_char dca_pad4[8]; /* chip registers */ u_char dca_pad5; vu_char dca_data; /* 0x11 */ u_char dca_pad6; vu_char dca_ier; /* 0x13 */ u_char dca_pad7; vu_char dca_iir; /* 0x15 (read) */ #define dca_fifo dca_iir /* 0x15 (write) */ u_char dca_pad8; vu_char dca_cfcr; /* 0x17 */ u_char dca_pad9; vu_char dca_mcr; /* 0x19 */ u_char dca_padA; vu_char dca_lsr; /* 0x1B */ u_char dca_padB; vu_char dca_msr; /* 0x1D */ }; #endif /* interface reset/id (300 only) */ #define DCAID0 0x02 #define DCAREMID0 0x82 #define DCAID1 0x42 #define DCAREMID1 0xC2 /* interrupt control (300 only) */ #define DCAIPL(x) ((((x) >> 4) & 3) + 3) #define IC_IR 0x40 #define IC_IE 0x80 /* * 16 bit baud rate divisor (lower byte in dca_data, upper in dca_ier) * NB: This constant is for a 7.3728 clock frequency. The 300 clock * frequency is 2.4576, giving a constant of 153600. */ #ifdef hp300 #define DCABRD(x) (153600 / (x)) #endif #ifdef hp700 #define DCABRD(x) (460800 / (x)) #endif /* interrupt enable register */ #define IER_ERXRDY 0x1 /* Enable receiver interrupt */ #define IER_ETXRDY 0x2 /* Enable transmitter empty interrupt */ #define IER_ERLS 0x4 /* Enable line status interrupt */ #define IER_EMSC 0x8 /* Enable modem status interrupt */ /* interrupt identification register */ #define IIR_IMASK 0xf #define IIR_RXTOUT 0xc #define IIR_RLS 0x6 /* Line status change */ #define IIR_RXRDY 0x4 /* Receiver ready */ #define IIR_TXRDY 0x2 /* Transmitter ready */ #define IIR_NOPEND 0x1 /* No pending interrupts */ #define IIR_MLSC 0x0 /* Modem status */ #define IIR_FIFO_MASK 0xc0 /* set if FIFOs are enabled */ /* fifo control register */ #define FIFO_ENABLE 0x01 /* Turn the FIFO on */ #define FIFO_RCV_RST 0x02 /* Reset RX FIFO */ #define FIFO_XMT_RST 0x04 /* Reset TX FIFO */ #define FIFO_DMA_MODE 0x08 #define FIFO_TRIGGER_1 0x00 /* Trigger RXRDY intr on 1 character */ #define FIFO_TRIGGER_4 0x40 /* ibid 4 */ #define FIFO_TRIGGER_8 0x80 /* ibid 8 */ #define FIFO_TRIGGER_14 0xc0 /* ibid 14 */ /* character format control register */ #define CFCR_DLAB 0x80 #define CFCR_SBREAK 0x40 #define CFCR_PZERO 0x30 #define CFCR_PONE 0x20 #define CFCR_PEVEN 0x10 #define CFCR_PODD 0x00 #define CFCR_PENAB 0x08 #define CFCR_STOPB 0x04 #define CFCR_8BITS 0x03 #define CFCR_7BITS 0x02 #define CFCR_6BITS 0x01 #define CFCR_5BITS 0x00 /* modem control register */ #define MCR_LOOPBACK 0x10 /* Loop test: echos from TX to RX */ #define MCR_IEN 0x08 /* Out2: enables UART interrupts */ #define MCR_DRS 0x04 /* Out1: resets some internal modems */ #define MCR_RTS 0x02 /* Request To Send */ #define MCR_DTR 0x01 /* Data Terminal Ready */ /* line status register */ #define LSR_RCV_FIFO 0x80 #define LSR_TSRE 0x40 /* Transmitter empty: byte sent */ #define LSR_TXRDY 0x20 /* Transmitter buffer empty */ #define LSR_BI 0x10 /* Break detected */ #define LSR_FE 0x08 /* Framing error: bad stop bit */ #define LSR_PE 0x04 /* Parity error */ #define LSR_OE 0x02 /* Overrun, lost incoming byte */ #define LSR_RXRDY 0x01 /* Byte ready in Receive Buffer */ #define LSR_RCV_MASK 0x1f /* Mask for incoming data or error */ /* modem status register */ #define MSR_DCD 0x80 /* Current Data Carrier Detect */ #define MSR_RI 0x40 /* Current Ring Indicator */ #define MSR_DSR 0x20 /* Current Data Set Ready */ #define MSR_CTS 0x10 /* Current Clear to Send */ #define MSR_DDCD 0x08 /* DCD has changed state */ #define MSR_TERI 0x04 /* RI has toggled low to high */ #define MSR_DDSR 0x02 /* DSR has changed state */ #define MSR_DCTS 0x01 /* CTS has changed state */