/* $OpenBSD: zs.c,v 1.22 2006/01/09 20:56:59 miod Exp $ */ /* $NetBSD: zs.c,v 1.19 1998/01/12 19:22:18 thorpej Exp $ */ /* * Copyright (c) 1996-1998 Bill Studenmund * Copyright (c) 1995 Gordon W. Ross * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * 4. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Gordon Ross * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ /* * Zilog Z8530 Dual UART driver (machine-dependent part) * * Runs two serial lines per chip using slave drivers. * Plain tty/async lines use the zs_async slave. * Sun keyboard/mouse uses the zs_kbd/zs_ms slaves. * Other ports use their own mice & keyboard slaves. * * Credits & history: * * With NetBSD 1.1, port-mac68k started using a port of the port-sparc * (port-sun3?) zs.c driver (which was in turn based on code in the * Berkeley 4.4 Lite release). Bill Studenmund did the port, with * help from Allen Briggs and Gordon Ross . Noud de * Brouwer field-tested the driver at a local ISP. * * Bill Studenmund and Gordon Ross then ported the machine-independant * z8530 driver to work with port-mac68k. NetBSD 1.2 contained an * intermediate version (mac68k using a local, patched version of * the m.i. drivers), with NetBSD 1.3 containing a full version. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #ifdef DDB #include #endif /* Are these in a header file anywhere? */ /* Booter flags interface */ #define ZSMAC_RAW 0x01 #define ZSMAC_LOCALTALK 0x02 #define ZS_STD_BRG (57600*4) #include "zsc.h" /* get the # of zs chips defined */ /* * Some warts needed by z8530tty.c - */ int zs_def_cflag = (CREAD | CS8 | HUPCL); int zs_major = 12; /* * abort detection on console will now timeout after iterating on a loop * the following # of times. Cheep hack. Also, abort detection is turned * off after a timeout (i.e. maybe there's not a terminal hooked up). */ #define ZSABORT_DELAY 3000000 /* * Define interrupt levels. */ #define ZSHARD_PRI 4 /* Wired on the CPU board... */ /* * Serial port cards with zs chips on them are actually at the * NuBus interrupt level, which is lower than 4. But blocking * level 4 interrupts will block those interrupts too, so level * 4 is fine. */ /* The layout of this is hardware-dependent (padding, order). */ struct zschan { volatile u_char zc_csr; /* ctrl,status, and indirect access */ u_char zc_xxx0; u_char zc_xxx1; /* part of the other channel lives here!*/ u_char zc_xxx2; /* Yea Apple! */ volatile u_char zc_data; /* data */ u_char zc_xxx3; u_char zc_xxx4; u_char zc_xxx5; }; /* Saved PROM mappings */ static char *zsaddr[NZSC]; /* See zs_init() */ /* Flags from cninit() */ static int zs_hwflags[NZSC][2]; /* Default speed for each channel */ static int zs_defspeed[NZSC][2] = { { 9600, /* tty00 */ 9600 }, /* tty01 */ }; void *zs_conschan = 0; int zs_consunit; /* device to which the console is attached--if serial. */ dev_t mac68k_zsdev; /* Mac stuff */ volatile unsigned char *sccA = 0; int nzsc_attached = 0; /* needed as long as we have spurious * interrupt problems. */ static struct zschan *zs_get_chan_addr(int zsc_unit, int channel); void zs_init(void); int zs_cn_check_speed(int bps); static struct zschan * zs_get_chan_addr(zsc_unit, channel) int zsc_unit, channel; { char *addr; struct zschan *zc; if (zsc_unit >= NZSC) return NULL; addr = zsaddr[zsc_unit]; if (addr == NULL) return NULL; if (channel == 0) { zc = (struct zschan *)(addr +2); /* handle the fact the ports are intertwined. */ } else { zc = (struct zschan *)(addr); } return (zc); } /* Find PROM mappings (for console support). */ int zsinited = 0; /* 0 = not, 1 = inited, not attached, 2= attached */ void zs_init() { if ((zsinited == 2)&&(zsaddr[0] != (char *) sccA)) panic("Moved zs0 address after attached!"); zsaddr[0] = (char *) sccA; zsinited = 1; if (zs_conschan != 0){ /* we might have moved io under the console */ zs_conschan = zs_get_chan_addr(0, zs_consunit); /* so recalc the console port */ } } /* * Even though zsparam will set up the clock multiples, etc., we * still set them here as: 1) mice & keyboards don't use zsparam, * and 2) the console stuff uses these defaults before device * attach. */ static u_char zs_init_reg[16] = { 0, /* 0: CMD (reset, etc.) */ ZSWR1_RIE | ZSWR1_TIE | ZSWR1_SIE, 0x18 + ZSHARD_PRI, /* IVECT */ ZSWR3_RX_8 | ZSWR3_RX_ENABLE, ZSWR4_CLK_X16 | ZSWR4_ONESB | ZSWR4_EVENP, ZSWR5_TX_8 | ZSWR5_TX_ENABLE, 0, /* 6: TXSYNC/SYNCLO */ 0, /* 7: RXSYNC/SYNCHI */ 0, /* 8: alias for data port */ ZSWR9_MASTER_IE, 0, /*10: Misc. TX/RX control bits */ ZSWR11_TXCLK_BAUD | ZSWR11_RXCLK_BAUD, 14, /*12: BAUDLO (default=9600) */ 0, /*13: BAUDHI (default=9600) */ ZSWR14_BAUD_ENA, ZSWR15_BREAK_IE | ZSWR15_DCD_IE | ZSWR15_CTS_IE, }; /**************************************************************** * Autoconfig ****************************************************************/ /* Definition of the driver for autoconfig. */ static int zsc_match(struct device *, void *, void *); static void zsc_attach(struct device *, struct device *, void *); static int zsc_print(void *, const char *name); struct cfattach zsc_ca = { sizeof(struct zsc_softc), zsc_match, zsc_attach }; struct cfdriver zsc_cd = { NULL, "zsc", DV_DULL }; int zshard(void *); int zssoft(void *); /* * Is the zs chip present? */ static int zsc_match(parent, vcf, aux) struct device *parent; void *vcf; void *aux; { return 1; } /* * Attach a found zs. * * Match slave number to zs unit number, so that misconfiguration will * not set up the keyboard as ttya, etc. */ static void zsc_attach(parent, self, aux) struct device *parent; struct device *self; void *aux; { struct zsc_softc *zsc = (void *)self; struct zsc_attach_args zsc_args; volatile struct zschan *zc; struct xzs_chanstate *xcs; struct zs_chanstate *cs; int zsc_unit, channel; int s, chip, theflags; if (!zsinited) zs_init(); zsinited = 2; zsc_unit = zsc->zsc_dev.dv_unit; /* Make sure everything's inited ok. */ if (zsaddr[zsc_unit] == NULL) panic("zs_attach: zs%d not mapped", zsc_unit); chip = 0; #ifdef DEBUG printf(" chip type %d",chip); #endif printf("\n"); /* * Initialize software state for each channel. */ for (channel = 0; channel < 2; channel++) { zsc_args.channel = channel; zsc_args.hwflags = zs_hwflags[zsc_unit][channel]; xcs = &zsc->xzsc_xcs_store[channel]; cs = &xcs->xzs_cs; zsc->zsc_cs[channel] = cs; cs->cs_channel = channel; cs->cs_private = NULL; cs->cs_ops = &zsops_null; zc = zs_get_chan_addr(zsc_unit, channel); cs->cs_reg_csr = &zc->zc_csr; cs->cs_reg_data = &zc->zc_data; if (channel == 0) /* Double check interrupts are off */ zs_write_reg(cs, 9, 0); bcopy(zs_init_reg, cs->cs_creg, 16); bcopy(zs_init_reg, cs->cs_preg, 16); /* Current BAUD rate generator clock. */ cs->cs_brg_clk = ZS_STD_BRG; /* RTxC is 230400*16, so use 230400 */ cs->cs_defspeed = zs_defspeed[zsc_unit][channel]; cs->cs_defcflag = zs_def_cflag; /* Make these correspond to cs_defcflag (-crtscts) */ cs->cs_rr0_dcd = ZSRR0_DCD; cs->cs_rr0_cts = 0; cs->cs_wr5_dtr = ZSWR5_DTR; cs->cs_wr5_rts = 0; #ifdef __notyet__ cs->cs_slave_type = ZS_SLAVE_NONE; #endif /* Define BAUD rate stuff. */ xcs->cs_clocks[0].clk = ZS_STD_BRG * 16; xcs->cs_clocks[0].flags = ZSC_RTXBRG; xcs->cs_clocks[1].flags = ZSC_RTXBRG | ZSC_RTXDIV | ZSC_VARIABLE | ZSC_EXTERN; xcs->cs_clocks[2].flags = ZSC_TRXDIV | ZSC_VARIABLE; xcs->cs_clock_count = 3; if (channel == 0) { theflags = mac68k_machine.modem_flags; xcs->cs_clocks[1].clk = mac68k_machine.modem_dcd_clk; xcs->cs_clocks[2].clk = mac68k_machine.modem_cts_clk; } else { theflags = mac68k_machine.print_flags; xcs->cs_clocks[1].flags = ZSC_VARIABLE; /* * Yes, we aren't defining ANY clock source enables for * the printer's DCD clock in. The hardware won't let * us use it. But a clock will freak out the chip, so * we let you set it, telling us to bar interrupts on * the line. */ xcs->cs_clocks[1].clk = mac68k_machine.print_dcd_clk; xcs->cs_clocks[2].clk = mac68k_machine.print_cts_clk; } if (xcs->cs_clocks[1].clk) zsc_args.hwflags |= ZS_HWFLAG_NO_DCD; if (xcs->cs_clocks[2].clk) zsc_args.hwflags |= ZS_HWFLAG_NO_CTS; #ifdef DEBUG printf("zsc%d channel %d: d_speed %6d DCD clk %ld CTS clk %ld", zsc_unit, channel, cs->cs_defspeed, xcs->cs_clocks[1].clk, xcs->cs_clocks[2].clk); #endif /* Set defaults in our "extended" chanstate. */ xcs->cs_csource = 0; xcs->cs_psource = 0; xcs->cs_cclk_flag = 0; /* Nothing fancy by default */ xcs->cs_pclk_flag = 0; if (theflags & ZSMAC_RAW) { zsc_args.hwflags |= ZS_HWFLAG_RAW; #ifdef DEBUG printf(" (raw defaults)"); #endif } /* * XXX - This might be better done with a "stub" driver * (to replace zstty) that ignores LocalTalk for now. */ if (theflags & ZSMAC_LOCALTALK) { printf(" shielding from LocalTalk"); cs->cs_defspeed = 1; cs->cs_creg[ZSRR_BAUDLO] = cs->cs_preg[ZSRR_BAUDLO] = 0xff; cs->cs_creg[ZSRR_BAUDHI] = cs->cs_preg[ZSRR_BAUDHI] = 0xff; zs_write_reg(cs, ZSRR_BAUDLO, 0xff); zs_write_reg(cs, ZSRR_BAUDHI, 0xff); /* * If we might have LocalTalk, then make sure we have * the Baud rate low-enough to not do any damage. */ } /* * We used to disable chip interrupts here, but we now * do that in zscnprobe, just in case MacOS left the chip on. */ xcs->cs_chip = chip; /* Stash away a copy of the final H/W flags. */ xcs->cs_hwflags = zsc_args.hwflags; #ifdef DEBUG printf("\n"); #endif /* * Look for a child driver for this channel. * The child attach will setup the hardware. */ if (!config_found(self, (void *)&zsc_args, zsc_print)) { /* No sub-driver. Just reset it. */ u_char reset = (channel == 0) ? ZSWR9_A_RESET : ZSWR9_B_RESET; s = splzs(); zs_write_reg(cs, 9, reset); splx(s); } } if (current_mac_model->class == MACH_CLASSAV) { add_psc_lev4_intr(PSCINTR_SCCA, zshard, zsc); add_psc_lev4_intr(PSCINTR_SCCB, zshard, zsc); } else { intr_establish(zshard, zsc, ZSHARD_PRI, self->dv_xname); } /* XXX - Now safe to install interrupt handlers. */ /* * Set the master interrupt enable and interrupt vector. * (common to both channels, do it on A) */ cs = zsc->zsc_cs[0]; s = splzs(); /* interrupt vector */ zs_write_reg(cs, 2, zs_init_reg[2]); /* master interrupt control (enable) */ zs_write_reg(cs, 9, zs_init_reg[9]); nzsc_attached++; splx(s); } static int zsc_print(aux, name) void *aux; const char *name; { struct zsc_attach_args *args = aux; if (name != NULL) printf("%s: ", name); if (args->channel != -1) printf(" channel %d", args->channel); return UNCONF; } int zsmdioctl(cs, cmd, data) struct zs_chanstate *cs; u_long cmd; caddr_t data; { switch (cmd) { default: return (-1); } return (0); } void zsmd_setclock(cs) struct zs_chanstate *cs; { struct xzs_chanstate *xcs = (void *)cs; if (cs->cs_channel != 0) return; /* * If the new clock has the external bit set, then select the * external source. */ via_set_modem((xcs->cs_pclk_flag & ZSC_EXTERN) ? 1 : 0); } static int zssoftpending; /* * Do the minimum work to pull data off of the chip and queue it up * for later processing. */ int zshard(arg) void *arg; { struct zsc_softc *zsc = (struct zsc_softc *)arg; int rval; if (zsc == NULL) return 0; rval = 0; rval |= zsc_intr_hard(zsc); if ((zsc->zsc_cs[0]->cs_softreq) || (zsc->zsc_cs[1]->cs_softreq)) { /* zsc_req_softint(zsc); */ /* We are at splzs here, so no need to lock. */ if (zssoftpending == 0) { zssoftpending = 1; setsoftserial(); } } return (rval); } /* * Similar scheme as for zshard (look at all of them) */ int zssoft(arg) void *arg; { register struct zsc_softc *zsc; register int unit; /* This is not the only ISR on this IPL. */ if (zssoftpending == 0) return (0); /* * The soft intr. bit will be set by zshard only if * the variable zssoftpending is zero. */ zssoftpending = 0; for (unit = 0; unit < zsc_cd.cd_ndevs; ++unit) { zsc = zsc_cd.cd_devs[unit]; if (zsc == NULL) continue; (void) zsc_intr_soft(zsc); } return (1); } #ifndef ZS_TOLERANCE #define ZS_TOLERANCE 51 /* 5% in tenths of a %, plus 1 so that exactly 5% will be ok. */ #endif /* * check out a rate for acceptability from the internal clock * source. Used in console config to validate a requested * default speed. Placed here so that all the speed checking code is * in one place. * * != 0 means ok. */ int zs_cn_check_speed(bps) int bps; /* target rate */ { int tc, rate; tc = BPS_TO_TCONST(ZS_STD_BRG, bps); if (tc < 0) return 0; rate = TCONST_TO_BPS(ZS_STD_BRG, tc); if (ZS_TOLERANCE > abs(((rate - bps)*1000)/bps)) return 1; else return 0; } /* * Search through the signal sources in the channel, and * pick the best one for the baud rate requested. Return * a -1 if not achievable in tolerance. Otherwise return 0 * and fill in the values. * * This routine draws inspiration from the Atari port's zs.c * driver in NetBSD 1.1 which did the same type of source switching. * Tolerance code inspired by comspeed routine in isa/com.c. * * By Bill Studenmund, 1996-05-12 */ int zs_set_speed(cs, bps) struct zs_chanstate *cs; int bps; /* bits per second */ { struct xzs_chanstate *xcs = (void *) cs; int i, tc, tc0 = 0, tc1, s, sf = 0; int src, rate0, rate1, err, tol; if (bps == 0) return (0); src = -1; /* no valid source yet */ tol = ZS_TOLERANCE; /* * Step through all the sources and see which one matches * the best. A source has to match BETTER than tol to be chosen. * Thus if two sources give the same error, the first one will be * chosen. Also, allow for the possability that one source might run * both the BRG and the direct divider (i.e. RTxC). */ for (i=0; i < xcs->cs_clock_count; i++) { if (xcs->cs_clocks[i].clk <= 0) continue; /* skip non-existant or bad clocks */ if (xcs->cs_clocks[i].flags & ZSC_BRG) { /* check out BRG at /16 */ tc1 = BPS_TO_TCONST(xcs->cs_clocks[i].clk >> 4, bps); if (tc1 >= 0) { rate1 = TCONST_TO_BPS(xcs->cs_clocks[i].clk >> 4, tc1); err = abs(((rate1 - bps)*1000)/bps); if (err < tol) { tol = err; src = i; sf = xcs->cs_clocks[i].flags & ~ZSC_DIV; tc0 = tc1; rate0 = rate1; } } } if (xcs->cs_clocks[i].flags & ZSC_DIV) { /* * Check out either /1, /16, /32, or /64 * Note: for /1, you'd better be using a synchronized * clock! */ int b0 = xcs->cs_clocks[i].clk, e0 = abs(b0-bps); int b1 = b0 >> 4, e1 = abs(b1-bps); int b2 = b1 >> 1, e2 = abs(b2-bps); int b3 = b2 >> 1, e3 = abs(b3-bps); if (e0 < e1 && e0 < e2 && e0 < e3) { err = e0; rate1 = b0; tc1 = ZSWR4_CLK_X1; } else if (e0 > e1 && e1 < e2 && e1 < e3) { err = e1; rate1 = b1; tc1 = ZSWR4_CLK_X16; } else if (e0 > e2 && e1 > e2 && e2 < e3) { err = e2; rate1 = b2; tc1 = ZSWR4_CLK_X32; } else { err = e3; rate1 = b3; tc1 = ZSWR4_CLK_X64; } err = (err * 1000)/bps; if (err < tol) { tol = err; src = i; sf = xcs->cs_clocks[i].flags & ~ZSC_BRG; tc0 = tc1; rate0 = rate1; } } } #ifdef ZSMACDEBUG zsprintf("Checking for rate %d. Found source #%d.\n",bps, src); #endif if (src == -1) return (EINVAL); /* no can do */ /* * The M.I. layer likes to keep cs_brg_clk current, even though * we are the only ones who should be touching the BRG's rate. * * Note: we are assuming that any ZSC_EXTERN signal source comes in * on the RTxC pin. Correct for the mac68k obio zsc. */ if (sf & ZSC_EXTERN) cs->cs_brg_clk = xcs->cs_clocks[i].clk >> 4; else cs->cs_brg_clk = ZS_STD_BRG; /* * Now we have a source, so set it up. */ s = splzs(); xcs->cs_psource = src; xcs->cs_pclk_flag = sf; bps = rate0; if (sf & ZSC_BRG) { cs->cs_preg[4] = ZSWR4_CLK_X16; cs->cs_preg[11]= ZSWR11_RXCLK_BAUD | ZSWR11_TXCLK_BAUD; if (sf & ZSC_PCLK) { cs->cs_preg[14] = ZSWR14_BAUD_ENA | ZSWR14_BAUD_FROM_PCLK; } else { cs->cs_preg[14] = ZSWR14_BAUD_ENA; } tc = tc0; } else { cs->cs_preg[4] = tc0; if (sf & ZSC_RTXDIV) { cs->cs_preg[11] = ZSWR11_RXCLK_RTXC | ZSWR11_TXCLK_RTXC; } else { cs->cs_preg[11] = ZSWR11_RXCLK_TRXC | ZSWR11_TXCLK_TRXC; } cs->cs_preg[14]= 0; tc = 0xffff; } /* Set the BAUD rate divisor. */ cs->cs_preg[12] = tc; cs->cs_preg[13] = tc >> 8; splx(s); #ifdef ZSMACDEBUG zsprintf("Rate is %7d, tc is %7d, source no. %2d, flags %4x\n", \ bps, tc, src, sf); zsprintf("Registers are: 4 %x, 11 %x, 14 %x\n\n", cs->cs_preg[4], cs->cs_preg[11], cs->cs_preg[14]); #endif cs->cs_preg[5] |= ZSWR5_RTS; /* Make sure the drivers are on! */ /* Caller will stuff the pending registers. */ return (0); } int zs_set_modes(cs, cflag) struct zs_chanstate *cs; int cflag; /* bits per second */ { struct xzs_chanstate *xcs = (void*)cs; int s; /* * Make sure we don't enable hfc on a signal line we're ignoring. * As we enable CTS interrupts only if we have CRTSCTS or CDTRCTS, * this code also effectivly turns off ZSWR15_CTS_IE. * * Also, disable DCD interrupts if we've been told to ignore * the DCD pin. Happens on mac68k because the input line for * DCD can also be used as a clock input. (Just set CLOCAL.) * * If someone tries to turn an invalid flow mode on, Just Say No * (Suggested by gwr) */ #if 0 if ((cflag & CDTRCTS) && (cflag & (CRTSCTS | MDMBUF))) return (EINVAL); #endif if (xcs->cs_hwflags & ZS_HWFLAG_NO_DCD) { if (cflag & MDMBUF) return (EINVAL); cflag |= CLOCAL; } #if 0 if ((xcs->cs_hwflags & ZS_HWFLAG_NO_CTS) && (cflag & (CRTSCTS | CDTRCTS))) return (EINVAL); #endif /* * Output hardware flow control on the chip is horrendous: * if carrier detect drops, the receiver is disabled, and if * CTS drops, the transmitter is stoped IN MID CHARACTER! * Therefore, NEVER set the HFC bit, and instead use the * status interrupt to detect CTS changes. */ s = splzs(); if ((cflag & (CLOCAL | MDMBUF)) != 0) cs->cs_rr0_dcd = 0; else cs->cs_rr0_dcd = ZSRR0_DCD; /* * The mac hardware only has one output, DTR (HSKo in Mac * parlance). In HFC mode, we use it for the functions * typically served by RTS and DTR on other ports, so we * have to fake the upper layer out some. * * CRTSCTS we use CTS as an input which tells us when to shut up. * We make no effort to shut up the other side of the connection. * DTR is used to hang up the modem. * * In CDTRCTS, we use CTS to tell us to stop, but we use DTR to * shut up the other side. */ if ((cflag & CRTSCTS) != 0){ cs->cs_wr5_dtr = ZSWR5_DTR; cs->cs_wr5_rts = 0; cs->cs_rr0_cts = ZSRR0_CTS; #if 0 } else if ((cflag & CDTRCTS) != 0) { cs->cs_wr5_dtr = 0; cs->cs_wr5_rts = ZSWR5_DTR; cs->cs_rr0_cts = ZSRR0_CTS; #endif } else if ((cflag & MDMBUF) != 0) { cs->cs_wr5_dtr = 0; cs->cs_wr5_rts = ZSWR5_DTR; cs->cs_rr0_cts = ZSRR0_DCD; } else { cs->cs_wr5_dtr = ZSWR5_DTR; cs->cs_wr5_rts = 0; cs->cs_rr0_cts = 0; } splx(s); /* Caller will stuff the pending registers. */ return(0); } /* * Read or write the chip with suitable delays. * MacII hardware has the delay built in. * No need for extra delay. :-) However, some clock-chiped * macs, or zsc's on serial add-on boards might need it. */ #define ZS_DELAY() u_char zs_read_reg(cs, reg) struct zs_chanstate *cs; u_char reg; { u_char val; *cs->cs_reg_csr = reg; ZS_DELAY(); val = *cs->cs_reg_csr; ZS_DELAY(); return val; } void zs_write_reg(cs, reg, val) struct zs_chanstate *cs; u_char reg, val; { *cs->cs_reg_csr = reg; ZS_DELAY(); *cs->cs_reg_csr = val; ZS_DELAY(); } u_char zs_read_csr(cs) struct zs_chanstate *cs; { u_char val; val = *cs->cs_reg_csr; ZS_DELAY(); /* make up for the fact CTS is wired backwards */ val ^= ZSRR0_CTS; return val; } void zs_write_csr(cs, val) struct zs_chanstate *cs; register u_char val; { /* Note, the csr does not write CTS... */ *cs->cs_reg_csr = val; ZS_DELAY(); } u_char zs_read_data(cs) struct zs_chanstate *cs; { register u_char val; val = *cs->cs_reg_data; ZS_DELAY(); return val; } void zs_write_data(cs, val) struct zs_chanstate *cs; u_char val; { *cs->cs_reg_data = val; ZS_DELAY(); } /**************************************************************** * Console support functions (mac68k specific!) * Note: this code is allowed to know about the layout of * the chip registers, and uses that to keep things simple. * XXX - I think I like the mvme167 code better. -gwr * XXX - Well :-P :-) -wrs ****************************************************************/ #define zscnpollc nullcnpollc cons_decl(zs); static void zs_putc(register volatile struct zschan *, int); static int zs_getc(register volatile struct zschan *); static void zscnsetup(void); extern int zsopen( dev_t dev, int flags, int mode, struct proc *p); /* * Console functions. */ /* * This code modled after the zs_setparam routine in zskgdb * It sets the console unit to a known state so we can output * correctly. */ static void zscnsetup() { struct xzs_chanstate xcs; struct zs_chanstate *cs; struct zschan *zc; int tconst, s; /* Setup temporary chanstate. */ bzero((caddr_t)&xcs, sizeof(xcs)); cs = &xcs.xzs_cs; zc = zs_conschan; cs->cs_reg_csr = &zc->zc_csr; cs->cs_reg_data = &zc->zc_data; cs->cs_channel = zs_consunit; cs->cs_brg_clk = ZS_STD_BRG; bcopy(zs_init_reg, cs->cs_preg, 16); cs->cs_preg[5] |= ZSWR5_DTR | ZSWR5_RTS; cs->cs_preg[15] = ZSWR15_BREAK_IE; tconst = BPS_TO_TCONST(cs->cs_brg_clk, zs_defspeed[0][zs_consunit]); cs->cs_preg[12] = tconst; cs->cs_preg[13] = tconst >> 8; /* can't use zs_set_speed as we haven't set up the * signal sources, and it's not worth it for now */ /* * As zs_loadchannelregs doesn't touch reg 9 (interrupt control), * we won't accidentally turn on interrupts below */ s = splhigh(); zs_loadchannelregs(cs); splx(s); } /* * zscnprobe is the routine which gets called as the kernel is trying to * figure out where the console should be. Each io driver which might * be the console (as defined in mac68k/conf.c) gets probed. The probe * fills in the consdev structure. Important parts are the device #, * and the console priority. Values are CN_DEAD (don't touch me), * CN_NORMAL (I'm here, but elsewhere might be better), CN_INTERNAL * (the video, better than CN_NORMAL), and CN_REMOTE (pick me!) * * As the mac's a bit different, we do extra work here. We mainly check * to see if we have serial echo going on. Also chould check for default * speeds. */ void zscnprobe(struct consdev * cp) { extern u_long IOBase; int maj, unit, i; for (maj = 0; maj < nchrdev; maj++) { if (cdevsw[maj].d_open == zsopen) { break; } } if (maj != nchrdev) { cp->cn_pri = CN_NORMAL; /* Lower than CN_INTERNAL */ if (mac68k_machine.serial_console != 0) { cp->cn_pri = CN_REMOTE; /* Higher than CN_INTERNAL */ mac68k_machine.serial_boot_echo =0; } unit = (mac68k_machine.serial_console == 1) ? 0 : 1; zs_consunit = unit; zs_conschan = (struct zschan *) -1; /* dummy flag for zs_init() */ mac68k_zsdev = cp->cn_dev = makedev(maj, unit); } if (mac68k_machine.serial_boot_echo) { /* * at this point, we know that we don't have a serial * console, but are doing echo */ zs_conschan = (struct zschan *) -1; /* dummy flag for zs_init() */ zs_consunit = 1; /* printer port */ } if ((i = mac68k_machine.modem_d_speed) > 0) { if (zs_cn_check_speed(i)) zs_defspeed[0][0] = i; } if ((i = mac68k_machine.print_d_speed) > 0) { if (zs_cn_check_speed(i)) zs_defspeed[0][1] = i; } mac68k_set_io_offsets(IOBase); zs_init(); /* * zsinit will set up the addresses of the scc. It will also, if * zs_conschan != 0, calculate the new address of the conschan for * unit zs_consunit. So if we are (or think we are) going to use the * chip for console I/O, we just set up the internal addresses for it. * * Now turn off interrupts for the chip. Note: this code piece is the * only vestage of the NetBSD 1.0 ser driver. :-) */ unit = sccA[2]; /* reset reg. access */ unit = sccA[0]; sccA[2] = 9; sccA[2] = 0; /* write 0 to reg. 9, clearing MIE */ sccA[2] = ZSWR0_CLR_INTR; unit = sccA[2]; /* reset any pending ints. */ sccA[0] = ZSWR0_CLR_INTR; unit = sccA[0]; if (mac68k_machine.serial_boot_echo) zscnsetup(); } void zscninit(struct consdev * cp) { zs_hwflags[0][zs_consunit] = ZS_HWFLAG_CONSOLE; /* * zsinit will set up the addresses of the scc. It will also, if * zs_conschan != 0, calculate the new address of the conschan for * unit zs_consunit. So zs_init implicitly sets zs_conschan to the right * number. :-) */ zscnsetup(); } /* * Polled input char. */ static int zs_getc(zc) register volatile struct zschan *zc; { register int s, c, rr0; s = splhigh(); /* Wait for a character to arrive. */ do { rr0 = zc->zc_csr; ZS_DELAY(); } while ((rr0 & ZSRR0_RX_READY) == 0); c = zc->zc_data; ZS_DELAY(); splx(s); return (c); } /* * Polled output char. */ static void zs_putc(zc, c) register volatile struct zschan *zc; int c; { register int s, rr0; register long wait = 0; s = splhigh(); /* Wait for transmitter to become ready. */ do { rr0 = zc->zc_csr; ZS_DELAY(); } while (((rr0 & ZSRR0_TX_READY) == 0) && (wait++ < 1000000)); if ((rr0 & ZSRR0_TX_READY) != 0) { zc->zc_data = c; ZS_DELAY(); } splx(s); } /* * Polled console input putchar. */ int zscngetc(dev) dev_t dev; { register volatile struct zschan *zc = zs_conschan; register int c; c = zs_getc(zc); return (c); } /* * Polled console output putchar. */ void zscnputc(dev, c) dev_t dev; int c; { register volatile struct zschan *zc = zs_conschan; zs_putc(zc, c); } /* * Handle user request to enter kernel debugger. */ void zs_abort(cs) struct zs_chanstate *cs; { volatile struct zschan *zc = zs_conschan; int rr0; register long wait = 0; /* Wait for end of break to avoid PROM abort. */ do { rr0 = zc->zc_csr; ZS_DELAY(); } while ((rr0 & ZSRR0_BREAK) && (wait++ < ZSABORT_DELAY)); if (wait > ZSABORT_DELAY) return; /* XXX */ #ifdef DDB if (db_console) Debugger(); #endif }