/* * Something to put append a 'U' to a long constant if it's C so that * it'll be unsigned in both ANSI and traditional. */ #if defined(ASSEMBLER) # define U(num) num #else # if defined(__STDC__) # define U(num) num ## U # else # define U(num) num/**/U # endif #endif /*********************** CONFIGURATION *******************************/ #define MAXPORTS 2 /* max count of PORTS/DUART */ /* * The following define is for the utputc/utgetc Console routines * which have to work without any configuration. */ #define MVME188_DUART U(0xFFF82000) /* M68692 DUART chip */ /*********************** DEFINITIONS *********************************/ #define MISSING 0 /* flag, missing a configured DUART */ #define ON 1 /* flag for modem() */ #define OFF 0 /* flag for modem() */ #define A_PORT 0 /* flag for port a */ #define B_PORT 1 /* flag for port b */ /*********************** MACROS ***********************************/ /* * spl priority level should always be the same. */ #define SPLCLOCK spl6 /* set clock priority level */ #define SPLM681 splhi /* set ut driver priority level */ /* the access to the same command register must be delayed, because the chip has some hardware problems in this case */ #define DELAY_CR { volatile register i; for ( i=0; i<250; ++i ); } /*********************** MC68681 DEFINITIONS ************************/ #define PORTOFFSET 0x10 /* offset for port b address space */ /* mode register 1: MR1x operations */ #define RXRTS 0x80 /* enable receiver RTS */ #define PAREN 0x00 /* with parity */ #define PARDIS 0x10 /* no parity */ #define EVENPAR 0x00 /* even parity */ #define ODDPAR 0x04 /* odd parity */ #define CL5 0x00 /* 5 bits per char */ #define CL6 0x01 /* 6 bits per char */ #define CL7 0x02 /* 7 bits per char */ #define CL8 0x03 /* 8 bits per char */ #define PARMODEMASK 0x18 /* parity mode mask */ #define PARTYPEMASK 0x04 /* parity type mask */ #define CLMASK 0x03 /* character length mask */ /* mode register 2: MR2x operations */ #define TXRTS 0x20 /* enable transmitter RTS */ #define TXCTS 0x10 /* enable transmitter CTS */ #define SB2 0x0f /* 2 stop bits */ #define SB1 0x07 /* 1 stop bit */ #define SB1L5 0x00 /* 1 stop bit at 5 bits per character */ #define SBMASK 0x0f /* stop bit mask */ /* clock-select register: CSRx operations */ #define NOBAUD -1 /* 50 and 200 baud are not possible */ /* they are not in Baud register set 2 */ #define BD75 0x00 /* 75 baud */ #define BD110 0x11 /* 110 baud */ #define BD134 0x22 /* 134.5 baud */ #define BD150 0x33 /* 150 baud */ #define BD300 0x44 /* 300 baud */ #define BD600 0x55 /* 600 baud */ #define BD1200 0x66 /* 1200 baud */ #define BD1800 0xaa /* 1800 baud */ #define BD2400 0x88 /* 2400 baud */ #define BD4800 0x99 /* 4800 baud */ #define BD9600 0xbb /* 9600 baud */ #define BD19200 0xcc /* 19200 baud */ #define DEFBAUD BD9600 /* default value if baudrate is not possible */ /* channel command register: CRx operations */ #define MRRESET 0x10 /* reset mr pointer to mr1 */ #define RXRESET 0x20 /* reset receiver */ #define TXRESET 0x30 /* reset transmitter */ #define ERRRESET 0x40 /* reset error status */ #define BRKINTRESET 0x50 /* reset channel's break interrupt */ #define BRKSTART 0x60 /* start break */ #define BRKSTOP 0x70 /* stop break */ #define TXDIS 0x08 /* disable transmitter */ #define TXEN 0x04 /* enable transmitter */ #define RXDIS 0x02 /* disable receiver */ #define RXEN 0x01 /* enable receiver */ /* status register: SRx status */ #define RBRK 0x80 /* received break */ #define FRERR 0x40 /* frame error */ #define PERR 0x20 /* parity error */ #define ROVRN 0x10 /* receiver overrun error */ #define TXEMT 0x08 /* transmitter empty */ #define TXRDY 0x04 /* transmitter ready */ #define FFULL 0x02 /* receiver FIFO full */ #define RXRDY 0x01 /* receiver ready */ /* output port configuration register: OPCR operations */ #define OPSET 0x00 /* set all op lines to op function */ #define OPSETTO 0x04 /* use OP3 for timer output */ /* output port register: OP operations */ #define OPDTRB 0x20 /* DTR line output b on the VME188, 181, 141 */ #define OPDTRA 0x04 /* DTR line output a */ #define OPRTSB 0x02 /* RTS line output b */ #define OPRTSA 0x01 /* RTS line output a */ /* auxiliary control register: ACR operations */ #define BDSET1 0x00 /* baudrate generator set 1 */ #define BDSET2 0x80 /* baudrate generator set 2 */ #define CCLK1 0x60 /* timer clock: external rate. TA */ #define CCLK16 0x30 /* counter clock: x1 clk divided by 16 */ #define SLCTIM 0x7800/* timer count to get 60 Hz time slice (16.6ms ticks) */ #define IPDCDIB 0x08 /* IP3 change == DCD input on port B */ #define IPDCDIA 0x04 /* IP2 change == DCD input on port A */ /* input port change register: IPCR operations */ #define IPCRDCDB 0x80 /* IP3 change == DCD change on port B */ #define IPCRDCDA 0x40 /* IP2 change == DCD change on port A */ /* Defines for mvme335 */ #define IPDCDB 0x20 /* DCD line input b */ #define IPDCDA 0x10 /* DCD line input a */ #define IPDSRB 0x08 /* DSR line input b */ #define IPDSRA 0x04 /* DSR line input a */ #define IPCTSB 0x02 /* CTS line input b */ #define IPCTSA 0x01 /* CTS line input a */ /* interrupt status and mask register: ISR status and IMR mask */ #define IIPCHG 0x80 /* input port change */ #define IBRKB 0x40 /* delta break b */ #define IRXRDYB 0x20 /* receiver ready b */ #define ITXRDYB 0x10 /* transmitter ready b */ #define ITIMER 0x08 /* Enable timer interrupts. */ #define IBRKA 0x04 /* delta break a */ #define IRXRDYA 0x02 /* receiver ready a */ #define ITXRDYA 0x01 /* transmitter ready a */ /* interrupts from port a or b */ #define AINTPORT ( IRXRDYA | ITXRDYA ) #define BINTPORT ( IRXRDYB | ITXRDYB ) /* HW write register index for ut_wr_regs[] */ #define MR1A 0 /* mode register 1 a */ #define CSRA 1 /* clock-select register a*/ #define CRA 2 /* command register a */ #define TBA 3 /* transmitter buffer a */ #define ACR 4 /* auxialiary control register*/ #define IMR 5 /* interrupt mask register */ #define CTUR 6 /* counter/timer upper reg */ #define CTLR 7 /* counter/timer lower reg */ #define MR1B 8 /* mode register 1 b */ #define CSRB 9 /* clock-select register b*/ #define CRB 10 /* command register b */ #define TBB 11 /* transmitter buffer b */ #define IVR 12 /* interrupt vector register */ #define OPCR 13 /* output port config reg */ #define OPRSET 14 /* output port: bit set cmd */ #define OPRRESET 15 /* output port: bit reset cmd */ #define MR2A 16 /* mode register 2 a */ #define MR2B 17 /* mode register 2 b */ #define MAXREG 18 /* max count of registers */ /* * Structure of MC68681 hardware read registers. */ struct dart_rd_reg { volatile unsigned int rd_mra; /* mode register a */ volatile unsigned int rd_sra; /* status register a*/ volatile unsigned int dummy5; /* do not access */ volatile unsigned int rd_rba; /* receiver buffer a */ volatile unsigned int rd_ipcr; /* input port change register */ volatile unsigned int rd_isr; /* interrupt status register */ volatile unsigned int rd_cur; /* current MSB of counter */ volatile unsigned int rd_clr; /* current LSB of counter */ volatile unsigned int rd_mrb; /* mode register b */ volatile unsigned int rd_srb; /* status register b*/ volatile unsigned int dummyxb; /* do not access */ volatile unsigned int rd_rbb; /* receiver buffer b */ volatile unsigned int rd_ivr; /* interrupt vector register */ volatile unsigned int rd_ip; /* input port (unlatched) */ volatile unsigned int rd_ctstart; /* start-counter command */ volatile unsigned int rd_ctstop; /* stop-counter command */ }; /* * Structure of MC68681 hardware write registers. */ struct dart_wr_reg { volatile unsigned int wr_mra; /* mode register a */ volatile unsigned int wr_csra; /* clock-select register a*/ volatile unsigned int wr_cra; /* command register a */ volatile unsigned int wr_tba; /* transmitter buffer a */ volatile unsigned int wr_acr; /* auxialiary control register*/ volatile unsigned int wr_imr; /* interrupt mask register */ volatile unsigned int wr_ctur; /* counter/timer upper reg */ volatile unsigned int wr_ctlr; /* counter/timer lower reg */ volatile unsigned int wr_mrb; /* mode register b */ volatile unsigned int wr_csrb; /* clock-select register b*/ volatile unsigned int wr_crb; /* command register b */ volatile unsigned int wr_tbb; /* transmitter buffer b */ volatile unsigned int wr_ivr; /* interrupt vector register */ volatile unsigned int wr_opcr; /* output port config reg */ volatile unsigned int wr_oprset; /* output port: bit set cmd */ volatile unsigned int wr_oprreset;/* output port: bit reset cmd */ }; union dartreg { struct dart_rd_reg read; /* read registers */ struct dart_wr_reg write; /* write registers */ }; /* * Structure of MC68681 hardware port dependent read registers. */ struct dart_prd_reg { volatile unsigned int rd_mr; /* mode register */ volatile unsigned int rd_sr; /* status register */ volatile unsigned int dummy5; volatile unsigned int rd_rb; /* receiver buffer */ volatile unsigned int dummy9; volatile unsigned int dummy11; volatile unsigned int dummy13; volatile unsigned int dummy15; }; /* * Structure of MC68681 hardware port dependent write registers. */ struct dart_pwr_reg { volatile unsigned int wr_mr; /* mode register */ volatile unsigned int wr_csr; /* clock-select register */ volatile unsigned int wr_cr; /* command register */ volatile unsigned int wr_tb; /* transmitter buffer */ volatile unsigned int dummy9; volatile unsigned int dummy11; volatile unsigned int dummy13; volatile unsigned int dummy15; }; union dart_pt_io { struct dart_prd_reg read; /* read registers */ struct dart_pwr_reg write; /* write registers */ }; /* * Structure of saved registers */ struct dart_sv_reg { volatile unsigned char sv_mr1[MAXPORTS]; /* mode register 1 a */ volatile unsigned char sv_mr2[MAXPORTS]; /* mode register 2 a */ volatile unsigned char sv_csr[MAXPORTS]; /* clock-select register a*/ volatile unsigned char sv_cr[MAXPORTS]; /* command register a */ volatile unsigned char sv_acr; /* auxialiary control register*/ volatile unsigned char sv_imr; /* interrupt mask register */ volatile unsigned char sv_ivr; /* interrupt vector register */ }; /* defines for receiver and DCD scanner */ #define M681CSCAN 2 /* clock ticks for character scan */ #define M681_CHAR 01 /* character arrived flag (ut_work) */ #define M681_ACT 02 /* character in buffer flag (ut_work) */ #define M681_DCD 04 /* DCD wait flag (ut_work) */ /********************* SPECIAL IOCTL COMMAND DEFINITIONS ******************/ /* HWHAND ioctls same as in MVME331 driver */ #define MSETHWHAND (('m'<<8)+20) /* set hardware handshake */ #define MCLEARHWHAND (('m'<<8)+21) /* clear hardware handshake */ #define MGETHWHAND (('m'<<8)+22) /* get hardware handshake mode */ #define M681STATUS (('m'<<8)+40 ) /* get status of duarts */ #define M681GETSTAT (('m'<<8)+42 ) /* get statistics */ #ifdef STATISTICS struct dart_stat { int open_cnt; /* count of open calls */ int intr_cnt; /* count of interrupts */ int tx_cnt; /* count of transmitted characters */ int rx_cnt; /* count of received characters */ int brk_cnt; /* count of break events */ int rovrn_cnt; /* count of overruns */ int frerr_cnt; /* count of frame errors */ int perr_cnt; /* count of parity errors */ int rxoff_cnt; /* count of received XOFF chars */ int rxon_cnt; /* count of received XON chars */ int txoff_cnt; /* count of transmitted XOFF chars */ int txon_cnt; /* count of transmitted XON chars */ }; #endif