/* $OpenBSD: sshreg.h,v 1.2 2001/03/07 23:57:47 miod Exp $ */ /* * Copyright (c) 1990 The Regents of the University of California. * All rights reserved. * * This code is derived from software contributed to Berkeley by * Van Jacobson of Lawrence Berkeley Laboratory. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by the University of * California, Berkeley and its contributors. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * @(#)sshreg.h 7.3 (Berkeley) 2/5/91 */ /* * NCR 53C710 SCSI interface hardware description. * * From the Mach scsi driver for the 53C700 */ typedef struct { /*00*/ volatile unsigned char ssh_sien; /* rw: SCSI Interrupt Enable */ /*01*/ volatile unsigned char ssh_sdid; /* rw: SCSI Destination ID */ /*02*/ volatile unsigned char ssh_scntl1; /* rw: SCSI control reg 1 */ /*03*/ volatile unsigned char ssh_scntl0; /* rw: SCSI control reg 0 */ /*04*/ volatile unsigned char ssh_socl; /* rw: SCSI Output Control Latch */ /*05*/ volatile unsigned char ssh_sodl; /* rw: SCSI Output Data Latch */ /*06*/ volatile unsigned char ssh_sxfer; /* rw: SCSI Transfer reg */ /*07*/ volatile unsigned char ssh_scid; /* rw: SCSI Chip ID reg */ /*08*/ volatile unsigned char ssh_sbcl; /* ro: SCSI Bus Control Lines */ /*09*/ volatile unsigned char ssh_sbdl; /* ro: SCSI Bus Data Lines */ /*0a*/ volatile unsigned char ssh_sidl; /* ro: SCSI Input Data Latch */ /*0b*/ volatile unsigned char ssh_sfbr; /* ro: SCSI First Byte Received */ /*0c*/ volatile unsigned char ssh_sstat2; /* ro: SCSI status reg 2 */ /*0d*/ volatile unsigned char ssh_sstat1; /* ro: SCSI status reg 1 */ /*0e*/ volatile unsigned char ssh_sstat0; /* ro: SCSI status reg 0 */ /*0f*/ volatile unsigned char ssh_dstat; /* ro: DMA status */ /*10*/ volatile unsigned long ssh_dsa; /* rw: Data Structure Address */ /*14*/ volatile unsigned char ssh_ctest3; /* ro: Chip test register 3 */ /*15*/ volatile unsigned char ssh_ctest2; /* ro: Chip test register 2 */ /*16*/ volatile unsigned char ssh_ctest1; /* ro: Chip test register 1 */ /*17*/ volatile unsigned char ssh_ctest0; /* ro: Chip test register 0 */ /*18*/ volatile unsigned char ssh_ctest7; /* rw: Chip test register 7 */ /*19*/ volatile unsigned char ssh_ctest6; /* rw: Chip test register 6 */ /*1a*/ volatile unsigned char ssh_ctest5; /* rw: Chip test register 5 */ /*1b*/ volatile unsigned char ssh_ctest4; /* rw: Chip test register 4 */ /*1c*/ volatile unsigned long ssh_temp; /* rw: Temporary Stack reg */ /*20*/ volatile unsigned char ssh_lcrc; /* rw: LCRC value */ /*21*/ volatile unsigned char ssh_ctest8; /* rw: Chip test register 8 */ /*22*/ volatile unsigned char ssh_istat; /* rw: Interrupt Status reg */ /*23*/ volatile unsigned char ssh_dfifo; /* rw: DMA FIFO */ /*24*/ volatile unsigned char ssh_dcmd; /* rw: DMA Command Register */ /*25*/ volatile unsigned char ssh_dbc2; /* rw: DMA Byte Counter reg */ /*26*/ volatile unsigned char ssh_dbc1; /*27*/ volatile unsigned char ssh_dbc0; /*28*/ volatile unsigned long ssh_dnad; /* rw: DMA Next Address */ /*2c*/ volatile unsigned long ssh_dsp; /* rw: DMA SCRIPTS Pointer reg */ /*30*/ volatile unsigned long ssh_dsps; /* rw: DMA SCRIPTS Pointer Save reg */ /*34*/ volatile unsigned long ssh_scratch; /* rw: Scratch Register */ /*38*/ volatile unsigned char ssh_dcntl; /* rw: DMA Control reg */ /*39*/ volatile unsigned char ssh_dwt; /* rw: DMA Watchdog Timer */ /*3a*/ volatile unsigned char ssh_dien; /* rw: DMA Interrupt Enable */ /*3b*/ volatile unsigned char ssh_dmode; /* rw: DMA Mode reg */ /*3c*/ volatile unsigned long ssh_adder; } ssh_regmap_t; typedef volatile ssh_regmap_t *ssh_regmap_p; /* * Register defines */ /* Scsi control register 0 (scntl0) */ #define SSH_SCNTL0_ARB 0xc0 /* Arbitration mode */ # define SSH_ARB_SIMPLE 0x00 # define SSH_ARB_FULL 0xc0 #define SSH_SCNTL0_START 0x20 /* Start Sequence */ #define SSH_SCNTL0_WATN 0x10 /* (Select) With ATN */ #define SSH_SCNTL0_EPC 0x08 /* Enable Parity Checking */ #define SSH_SCNTL0_EPG 0x04 /* Enable Parity Generation */ #define SSH_SCNTL0_AAP 0x02 /* Assert ATN on Parity Error */ #define SSH_SCNTL0_TRG 0x01 /* Target Mode */ /* Scsi control register 1 (scntl1) */ #define SSH_SCNTL1_EXC 0x80 /* Extra Clock Cycle of data setup */ #define SSH_SCNTL1_ADB 0x40 /* Assert Data Bus */ #define SSH_SCNTL1_ESR 0x20 /* Enable Selection/Reselection */ #define SSH_SCNTL1_CON 0x10 /* Connected */ #define SSH_SCNTL1_RST 0x08 /* Assert RST */ #define SSH_SCNTL1_AESP 0x04 /* Assert even SCSI parity */ #define SSH_SCNTL1_RES0 0x02 /* Reserved */ #define SSH_SCNTL1_RES1 0x01 /* Reserved */ /* Scsi interrupt enable register (sien) */ #define SSH_SIEN_M_A 0x80 /* Phase Mismatch or ATN active */ #define SSH_SIEN_FCMP 0x40 /* Function Complete */ #define SSH_SIEN_STO 0x20 /* (Re)Selection timeout */ #define SSH_SIEN_SEL 0x10 /* (Re)Selected */ #define SSH_SIEN_SGE 0x08 /* SCSI Gross Error */ #define SSH_SIEN_UDC 0x04 /* Unexpected Disconnect */ #define SSH_SIEN_RST 0x02 /* RST asserted */ #define SSH_SIEN_PAR 0x01 /* Parity Error */ /* Scsi chip ID (scid) */ #define SSH_SCID_VALUE(i) (1< asserted */ #define SSH_ACK 0x40 #define SSH_BSY 0x20 #define SSH_SEL 0x10 #define SSH_ATN 0x08 #define SSH_MSG 0x04 #define SSH_CD 0x02 #define SSH_IO 0x01 #define SSH_PHASE(socl) SCSI_PHASE(socl) /* Scsi first byte received register (sfbr) */ /* Scsi input data latch register (sidl) */ /* Scsi bus data lines register (sbdl) */ /* Scsi bus control lines register (sbcl). Same as socl */ /* DMA status register (dstat) */ #define SSH_DSTAT_DFE 0x80 /* DMA FIFO empty */ #define SSH_DSTAT_RES 0x40 #define SSH_DSTAT_BF 0x20 /* Bus fault */ #define SSH_DSTAT_ABRT 0x10 /* Aborted */ #define SSH_DSTAT_SSI 0x08 /* SCRIPT Single Step */ #define SSH_DSTAT_SIR 0x04 /* SCRIPT Interrupt Instruction */ #define SSH_DSTAT_WTD 0x02 /* Watchdog Timeout Detected */ #define SSH_DSTAT_IID 0x01 /* Invalid Instruction Detected */ /* Scsi status register 0 (sstat0) */ #define SSH_SSTAT0_M_A 0x80 /* Phase Mismatch or ATN active */ #define SSH_SSTAT0_FCMP 0x40 /* Function Complete */ #define SSH_SSTAT0_STO 0x20 /* (Re)Selection timeout */ #define SSH_SSTAT0_SEL 0x10 /* (Re)Selected */ #define SSH_SSTAT0_SGE 0x08 /* SCSI Gross Error */ #define SSH_SSTAT0_UDC 0x04 /* Unexpected Disconnect */ #define SSH_SSTAT0_RST 0x02 /* RST asserted */ #define SSH_SSTAT0_PAR 0x01 /* Parity Error */ /* Scsi status register 1 (sstat1) */ #define SSH_SSTAT1_ILF 0x80 /* Input latch (sidl) full */ #define SSH_SSTAT1_ORF 0x40 /* output reg (sodr) full */ #define SSH_SSTAT1_OLF 0x20 /* output latch (sodl) full */ #define SSH_SSTAT1_AIP 0x10 /* Arbitration in progress */ #define SSH_SSTAT1_LOA 0x08 /* Lost arbitration */ #define SSH_SSTAT1_WOA 0x04 /* Won arbitration */ #define SSH_SSTAT1_RST 0x02 /* SCSI RST current value */ #define SSH_SSTAT1_SDP 0x01 /* SCSI SDP current value */ /* Scsi status register 2 (sstat2) */ #define SSH_SSTAT2_FF 0xf0 /* SCSI FIFO flags (bytecount) */ # define SSH_SCSI_FIFO_DEEP 8 #define SSH_SSTAT2_SDP 0x08 /* Latched (on REQ) SCSI SDP */ #define SSH_SSTAT2_MSG 0x04 /* Latched SCSI phase */ #define SSH_SSTAT2_CD 0x02 #define SSH_SSTAT2_IO 0x01 /* Chip test register 0 (ctest0) */ #define SSH_CTEST0_RES0 0x80 #define SSH_CTEST0_BTD 0x40 /* Byte-to-byte Timer Disable */ #define SSH_CTEST0_GRP 0x20 /* Generate Receive Parity for Passthrough */ #define SSH_CTEST0_EAN 0x10 /* Enable Active Negation */ #define SSH_CTEST0_HSC 0x08 /* Halt SCSI clock */ #define SSH_CTEST0_ERF 0x04 /* Extend REQ/ACK Filtering */ #define SSH_CTEST0_RES1 0x02 #define SSH_CTEST0_DDIR 0x01 /* Xfer direction (1-> from SCSI bus) */ /* Chip test register 1 (ctest1) */ #define SSH_CTEST1_FMT 0xf0 /* Byte empty in DMA FIFO bottom (high->byte3) */ #define SSH_CTEST1_FFL 0x0f /* Byte full in DMA FIFO top, same */ /* Chip test register 2 (ctest2) */ #define SSH_CTEST2_RES 0x80 #define SSH_CTEST2_SIGP 0x40 /* Signal process */ #define SSH_CTEST2_SOFF 0x20 /* Synch Offset compare (1-> zero Init, max Tgt */ #define SSH_CTEST2_SFP 0x10 /* SCSI FIFO Parity */ #define SSH_CTEST2_DFP 0x08 /* DMA FIFO Parity */ #define SSH_CTEST2_TEOP 0x04 /* True EOP (a-la 5380) */ #define SSH_CTEST2_DREQ 0x02 /* DREQ status */ #define SSH_CTEST2_DACK 0x01 /* DACK status */ /* Chip test register 3 (ctest3) read-only, top of SCSI FIFO */ /* Chip test register 4 (ctest4) */ #define SSH_CTEST4_MUX 0x80 /* Host bus multiplex mode */ #define SSH_CTEST4_ZMOD 0x40 /* High-impedance outputs */ #define SSH_CTEST4_SZM 0x20 /* ditto, SCSI "outputs" */ #define SSH_CTEST4_SLBE 0x10 /* SCSI loobpack enable */ #define SSH_CTEST4_SFWR 0x08 /* SCSI FIFO write enable (from sodl) */ #define SSH_CTEST4_FBL 0x07 /* DMA FIFO Byte Lane select (from ctest6) 4->0, .. 7->3 */ /* Chip test register 5 (ctest5) */ #define SSH_CTEST5_ADCK 0x80 /* Clock Address Incrementor */ #define SSH_CTEST5_BBCK 0x40 /* Clock Byte counter */ #define SSH_CTEST5_ROFF 0x20 /* Reset SCSI offset */ #define SSH_CTEST5_MASR 0x10 /* Master set/reset pulses (of bits 3-0) */ #define SSH_CTEST5_DDIR 0x08 /* (re)set internal DMA direction */ #define SSH_CTEST5_EOP 0x04 /* (re)set internal EOP */ #define SSH_CTEST5_DREQ 0x02 /* (re)set internal REQ */ #define SSH_CTEST5_DACK 0x01 /* (re)set internal ACK */ /* Chip test register 6 (ctest6) DMA FIFO access */ /* Chip test register 7 (ctest7) */ #define SSH_CTEST7_CDIS 0x80 /* Cache burst disable */ #define SSH_CTEST7_SC1 0x40 /* Snoop control 1 */ #define SSH_CTEST7_SC0 0x20 /* Snoop contorl 0 */ #define SSH_CTEST7_INHIBIT (0 << 5) #define SSH_CTEST7_SNOOP (1 << 5) #define SSH_CTEST7_INVAL (2 << 5) #define SSH_CTEST7_RESV (3 << 5) #define SSH_CTEST7_STD 0x10 /* Selection timeout disable */ #define SSH_CTEST7_DFP 0x08 /* DMA FIFO parity bit */ #define SSH_CTEST7_EVP 0x04 /* Even parity (to host bus) */ #define SSH_CTEST7_TT1 0x02 /* Transfer type bit */ #define SSH_CTEST7_DIFF 0x01 /* Differential mode */ /* DMA FIFO register (dfifo) */ #define SSH_DFIFO_RES 0x80 #define SSH_DFIFO_BO 0x7f /* FIFO byte offset counter */ /* Interrupt status register (istat) */ #define SSH_ISTAT_ABRT 0x80 /* Abort operation */ #define SSH_ISTAT_RST 0x40 /* Software reset */ #define SSH_ISTAT_SIGP 0x20 /* Signal process */ #define SSH_ISTAT_RES 0x10 #define SSH_ISTAT_CON 0x08 /* Connected */ #define SSH_ISTAT_RES1 0x04 #define SSH_ISTAT_SIP 0x02 /* SCSI Interrupt pending */ #define SSH_ISTAT_DIP 0x01 /* DMA Interrupt pending */ /* Chip test register 8 (ctest8) */ #define SSH_CTEST8_V 0xf0 /* Chip revision level */ #define SSH_CTEST8_FLF 0x08 /* Flush DMA FIFO */ #define SSH_CTEST8_CLF 0x04 /* Clear DMA and SCSI FIFOs */ #define SSH_CTEST8_FM 0x02 /* Fetch pin mode */ #define SSH_CTEST8_SM 0x01 /* Snoop pins mode */ /* DMA Mode register (dmode) */ #define SSH_DMODE_BL_MASK 0xc0 /* 0->1 1->2 2->4 3->8 */ #define SSH_DMODE_FC 0x30 /* Function code */ #define SSH_DMODE_PD 0x08 /* Program/data */ #define SSH_DMODE_FAM 0x04 /* Fixed address mode */ #define SSH_DMODE_U0 0x02 /* User programmable transfer type */ #define SSH_DMODE_MAN 0x01 /* Manual start mode */ /* DMA interrupt enable register (dien) */ #define SSH_DIEN_RES 0xc0 #define SSH_DIEN_BF 0x20 /* On Bus Fault */ #define SSH_DIEN_ABRT 0x10 /* On Abort */ #define SSH_DIEN_SSI 0x08 /* On SCRIPTS sstep */ #define SSH_DIEN_SIR 0x04 /* On SCRIPTS intr instruction */ #define SSH_DIEN_WTD 0x02 /* On watchdog timeout */ #define SSH_DIEN_IID 0x01 /* On illegal instruction detected */ /* DMA control register (dcntl) */ #define SSH_DCNTL_CF_MASK 0xc0 /* Clock frequency dividers: 0 --> 37.51..50.00 Mhz, div=2 1 --> 25.01..37.50 Mhz, div=1.5 2 --> 16.67..25.00 Mhz, div=1 3 --> 50.01..66.67 Mhz, div=3 */ #define SSH_DCNTL_EA 0x20 /* Enable ack */ #define SSH_DCNTL_SSM 0x10 /* Single step mode */ #define SSH_DCNTL_LLM 0x08 /* Enable SCSI Low-level mode */ #define SSH_DCNTL_STD 0x04 /* Start DMA operation */ #define SSH_DCNTL_FA 0x02 /* Fast arbitration */ #define SSH_DCNTL_COM 0x01 /* 53C700 compatibility */